User's Manual
Table Of Contents
- TABLE OF CONTENTS
- 1 GETTING STARTED 1
- 2 MECHANICAL SPECIFICATIONS 4
- 3 POWER AND ELECTRICAL INTERFACE 14
- Power from the MUX32 bus and from an ex ter nal power sup ply 26
- 3.9 LED In di ca tors 27
- 4 SERIAL AND BUS COMMUNICATIONS 29
- 5 MENU CONFIGURATION 34
- 6 RFID INTERFACE 41
- 6.1 In tro duc tion 41
- 6.2 ABx Er ror Codes 44
- 6.3 Anticollision Com mands 47
- 6.4 ABx Stan dard Pro to col 49
- ABxS Com mand 4 (04H): Fill Tag 49
- ABxS Com mand 5 (05H): Block Read 51
- ABxS Com mand 6 (06H): Block Write 53
- ABxS Com mand 7 (07H): Read Tag Se rial Num ber 55
- ABxS Com mand 8 (08H): Tag Search 56
- ABxS Com mand D (0DH): Con tin u ous Block Read 57
- ABxS Com mand 10 (10H): Set Out put 60
- ABxS Com mand 11 (11H): In put Sta tus 62
- ABxS Com mand 84 (84H): Fill Tag All 64
- ABxS Com mand 85 (85H): Block Read All 66
- ABxS Com mand 86 (86H): Block Write All 68
- ABxS Com mand 87 (87H): Read Tag SN All 70
- ABxS Com mand 88 (88H): Tag Search All 72
- ABxS Com mand 89 (89H): EAS Set/Re set All 73
- ABxS Com mand 8A (8AH): EAS Start/Stop 75
- ABxS Com mand 8D (8DH): Con tin u ous Read All 77
- ABxS Com mand 8E (8EH): Mem ory Lock All 79
- ABxS Com mand 94 (94H): SN Fill 81
- ABxS Com mand 95 (95H): SN Block Read 83
- ABxS Com mand 96 (96H): SN Block Write 85
- ABxS Com mand 97 (97H): SN Block Read All 87
- 6.5 ABx Fast Pro to col 89
- ABx Com mand Packet Struc ture: 89
- Com mand/Re sponse Size 90
- Checksum 91
- ABxF Com mand 4 (04H): Fill Tag 92
- ABxF Com mand 5 (05H): Block Read 94
- ABxF Com mand 6 (06H): Block Write 96
- ABxF Com mand 7 (07H): Read Tag Se rial Num ber 98
- ABxF Com mand 8 (08H): Tag Search 100
- ABxF Com mand D (0DH): Con tin u ous Block Read 101
- ABxF Com mand 10 (10H): Set Out put 104
- ABxF Com mand 11 (11H): In put Sta tus 106
- ABxF Com mand 84 (84H): Fill All 108
- ABxF Com mand 85 (85H): Block Read All 110
- ABxF Com mand 86 (86H): Block Write All 112
- ABxF Com mand 87 (87H): Read Tag SN All 114
- ABxF Com mand 88 (88H): Tag Search All 116
- ABxF Com mand 89 (89H): EAS Set/Re set All 118
- ABxF Com mand 8A (8AH): EAS Start/Stop 120
- ABxF Com mand 8D (8DH): Con tin u ous Read All 123
- ABxF Com mand 8E (8EH): Mem ory Lock All 126
- ABxF Com mand 94 (94H): SN Fill 128
- ABxF Com mand 95 (95H): SN Block Read 130
- ABxF Com mand 96 (96H): SN Block Write 132
- ABxF Com mand 97 (97H): SN Block Read All 134
- 6.6 ABx ASCII Pro to col 138
fore downloading another version of software, display and record the current
configuration settings. Then download the new software version. Set switch
5 (on the main board) on and apply power to initialize the configuration pa
-
rameters to their default states. When the LEDs stop flashing, turn Switch 5
to Off and press the reset switch. Enter the Configuration Menu and re-enter
any non-default configuration parameters.
When you select 3 from the Main Menu, the LRP820 will prompt you to
begin the download.
*** Download DSP Firmware***
Press a key to start Downloading
After you have pressed a key, the LRP820 will display:
Send the Intel Hex file. Downloading now.
Send the new firmware via your terminal emulation program in ASCII text
or Hexadecimal format. The firmware will be automatically transferred to
the DSP Flash Memory. Wait 10 seconds after the download is complete
before resetting the LRP820.
Record: 750
Download OK
File Transfer to DSP
Blocco 24/24
DSP Flash Programming...
New Firmware Transferred to DSP
WARNING:
Do not download INTERFACE BOARD firmware to the main board.
IMPORTANT:
It is not necessary to download firmware into the unit unless instructed to do
so by Escort Memory Systems technical support personnel.
5.5 Exit to Operating Mode
This option is available if you wish to use temporary, unsaved, configuration
parameters. The unsaved options you have selected will be used until the
LRP820 is reset and the saved parameters are restored.
Copyright © 2000 Escort Memory Systems
40 LRP820-Series Long-Range Passive Reader/Writer