23456789012345678901234567890121234567890123456789012345678901212345678901234 123456789012345678901234567890121234567890123456789012345678901212345678901234 123456789012345678901234567890121234567890123456789012345678901212345678901234 123456789012345678901234567890121234567890123456789012345678901212345678901234 123456789012345678901234567890121234567890123456789012345678901212345678901234 123456789012345678901234567890121234567890123456789012345678901212345678901234 12345678901234567890123456789012123456
Flipper-48HR Part Drawing Description P1 Top Platform P2 Left Leg 48” Half-round Conference Table Part Qty 1 EA P8 Drawing Description Crossbrace Qty 1 EA 1 EA Hardware List P3 P4 P5 Right Leg (with Spring) Metal Stability Panel A 9/16” Socket Screw 4 EA A1 1-3/8” Socket Screw 2 EA B 1-7/8” Socket Screw 4 EA C Plastic Grommet 1 EA D 2” Locking Caster 4 EA E Allen Wrench 1 EA Caster Wrench 1 EA 1 EA 1 EA Welded Rod Assembly 1 EA P6 Left Side Handle 1 EA F P7 R
Flipper-48HR Assembly Diagram READ THROUGH INSTRUCTIONS FROM BEGINNING TO END BEFORE STARTING TO ASSEMBLE UNIT. 1.) Identify and Separate all the Parts and Hardware. 2.) Slide the Right Side Handle (P7) Through the Right Leg (P-3) and into the Welded Rod (P5) as shown in illustration #1. Rotate Right Side Handle (P7) until holes are aligned (See illustration#1). Secure using 1 Screw (A). 3.) Slide the Left Side Handle (P6) Through the Left Leg (P-2) and into the Welded Rod (P5) as shown in illustration #1.
.) Attach Metal Stability Panel (P4) and Crossbrace (P-8) to the Right Leg (P-3) and Left Leg (P2) using 2 Screws (A) and 2 Screws (A1) as shown in illustration #2. Illustration #2 P3 P2 P4 A1 P8 (A) Screw M6 X 9/16” For Scale only A (A1) Screw M6 X 1-3/8” For Scale only 5.) Insert Spring on Right Leg (P3) into the notch in Welded Rod (P5) as shown in illustration # 3.
6.) Place the Top Platform (P1) with the insert nuts facing up. Attach Right Leg (P-3) and Left Leg (P2) using 4 each (B) screws as shown in illustration #4. (Finger tighten only) 7.) Attach 4 each (D) Locking Casters to the front and back of the Right Leg (P-3) and Left Leg (P2). Tighten Casters using Caster Wrench (F). (Tighten all screws using Allen Wrench (E).
Grommet(D) installation Illustration #5 8.) To install Grommet (C), separate parts and press Grommet Sleeve in rectangular openings in Top Platform (P1) as shown in illustration #5. Grommet (C) 9.) Snap 2 plastic Caps over top of Sleeve as shown in illustration #5. Cap Cap Sleeve Cap P1 Cap Sleeve C Important The Balt product you have purchased is guaranteed against material and workmanship defects. This guarantee extends 1 year from date of purchase.
89773 Flipper-48HR 48” Half-round Conference Table For more information 1-800-749-2258 48 24 29½ 28 19 Shipping Information 3.9 Cubic Feet 48 lbs.