Operating instructions

P44987 Revision “B“ Page 5 of 10
Notes:
Apply Item 34 (Grease) to:
Item 4 (Cut off Cam)
Item 3 (Cutter Knife) at contact point with item 1 (Tool Head)
Item 27 (Spring) Before installation
Apply Item 35 (Grease) to:
Item 7 (Tension Screw) Threads and at Grooved end
Item 2 (Cutter Blade) Counter-bore only, after item 14 (Bearing Tip) has been
installed.
Tighten the following:
Item 24 (#10-32 Screw) to 60 – 70 in-lbs.
Item 23 (1/4-28 Screw) to 90 – 110 in-lbs.
Adjust Item 25 (Plunger) for positive detent action when item 6 (Handle) is
actuated.
35 C23187 .03 Lubricant, Black Moly, Hi-Temp (cc)
34 I16387 .05 Lubricant, Super Lube w/ Teflon (cc)
33 S19787 .01 Adhesive, Bonding, #415 (cc)
32 M07987 2 Threaded Insert, #10-32
31 M08087 4 Rivet, Blind, .125 X .328 Long
30 J64387 2 Pin, Spring, 3/16 X 5/8 Long
29 M08187 4 Washer, .128 ID X .238 OD
28 M01487 1 Pin, Dowel, ¼ Dia X 1.50 Long
27 A53587 2 Spring, Compression, .300 X 1.00 Long
26 A33887 1 Spring, Compression, .180 X .813 Long
25 M02487 2 Screw, Spring Plunger, ¼-20
24 M06187 4 Screw, Socket Head Cap, #10-32 X 3/8”
23 J67287 4 Screw, Socket Head Cap, ¼ X ½”
22 M05787 2 Screw, Socket Head Cap, ¼ X 1”
21 M05687 1 Grip, Textured, Gray
20 M07587 2 Wear Plate, Fin.
19 M07487 1 Body, Right, Finished, UL9000
18 M07387 1 Body, Left, Finished, UL9000
17 M04387 1 Tripper Bracket, Cast/Fin.
16 M02287 1 Tip, Load Bearing, Fin.
15 M06587 1 Ball, ¼” Diameter
14 M05387 1 Bearing Tip, Fin.
13 M01388 2 Pin, .187 Dia X 1.50 Long, Fin.
12 M00287 1 Roller, Cut-off, Fin.
11 M02387 1 Plate, Release, cast/fin.
10 M09187 1 Gripper Guide, UL2000
9 M01787 1 Plate, Back, Cast/Fin.
8 M08887 1 Gripper, UL2000
7 M00987 1 Tension Screw, Fin.
6 M04687 1 Handle, Cut-off, finished
5 M09087 1 Tension Block, Mach., UL2000
4 M08987 1 Cam, Cut-off, UL9000
3 M00687 1 Cutter Knife, UL001
2 M00787 1 Cutter Blade, UL001
1 M00587 1 Tool Head, Fin. UL9000
Ite
m
Part Numbe
r
Quan. Descriptio
n
UL9010 Electric Ultra-Lok Tool
Assembly Instructions