ZM Series Monitors User Manual ENGLISH bandg.
Preface As Navico is continuously improving this product, we retain the right to make changes to the product at any time which may not be reflected in this version of the manual. Please contact your nearest distributor if you require any further assistance. It is the owner’s sole responsibility to install and use the equipment in a manner that will not cause accidents, personal injury or property damage. The user of this product is solely responsible for observing safe boating practices.
About this manual This manual is a reference guide for installing and operating the B&G Series monitors. The manual does not cover basic background information about how equipment such as radars, echosounders and AIS work. Important text that requires special attention from the reader is emphasized as follows: ¼¼ Note: Used to draw the reader’s attention to a comment or some important information.
Contents 6 Introduction 6 Items included 7 Display installation 7 7 8 11 Cutout template Fixing options Flush mounting the display VESA mounting the display 12 Connecting the display 12 12 12 13 14 14 14 15 15 15 Rear connections HDMI cable Cable retention Connecting power Connecting touch control Serial connection USB connection Connecting NMEA 2000 Connecting HDMI cable Typical installation 16 Operating the display 16 16 16 18 18 18 First time operation Shortcut functions OSD menu Updating
1 Introduction The B&G ZM Series monitors offer a low profile, high brightness solution for displaying video from a variety of sources. This includes two models; the ZM16”, and ZM19” Touch monitors. These models are suited for both indoor and outdoor use. Both monitors accept video via HDMI, DVI-I and composite inputs.
2 Display installation It is recommended that the unit be powered and connected to a video source to assist in selecting a suitable mounting location, prior to irreversible modification of the vessel’s helm station. When planning the display location, the following points should be considered to ensure safe, comfortable and reliable operation: • Convenience - the mounting location should be easily accessible to allow operation of the controls and should enable easy viewing of the display.
Flush mounting the display ¼¼ Note: The following guidelines and warnings apply: Important drill bit size selection information Soft materials e.g. Plywood 1.9 - 2.3 mm (5/64") Hard materials e.g. GRP, Acrylic, hardwoods 2.3 - 2.5 mm (3/32") Max 5.5 mm (0.22”) Front mount screw recommendations 1. Fit the supplied M4 machine screws, washers, and plastic spacers to each of the four threaded fittings on the back case of screen. Hand tighten only. 2. 1 X4 2 3 x2 200 .0 117.5 mm (4.63") 111.
5. 6. 7. Place the display in the dash hole. Place the guide tool on the glass of the display. Slide the tool across so the drill bit hole guide lines up with the center of a screw location hole on the case of the display. Drill the pilot hole. 8. ¼¼ Note: Before drilling the rest of the pilot holes it is recommended to secure the display with at least one screw to allow for movement in the dash cutout. 9. Insert one of the supplied screws in to the screw guide and tighten using a hand screw driver.
15. With bracket making contact with back of monitor, slide bracket down till it engages with a click and is held in place. 18. Hand tighten wing nuts against the back of the mounting brackets to lock the wing screw in place. Hold wing screw stationary if it turns while adjusting the wingnut. CLICK 16. 17. 19. 10 | Wind in the wing screw, until stoppers make firm contact with rear of dashboard material. Check front of unit, ensuring that unit’s bezel is making even contact with the dash surface.
VESA mounting the display A VESA bracket adaptor is available as an optional part for all display sizes, allowing a variety of wall and free standing bracket mounting options. The fasteners for attachment to the display are included with the bracket. Monitors mounted using a Vesa bracket have IPX2 rating, and should be mounted in an area sheltered from rain and sea spray. ¼¼ Note: The monitor should not be tilted forward by more than 15 degrees, as this compromises the IPX2 rating.
3 Connecting the display The ZM series monitors largely use industry standard cables, which can be purchased preterminated in a variety of lengths. The following chapter provides additional detail where cables require field termination by the installer. Rear connections 1 No.
With the cable and plug fitted in place, secure the cable to the retention bracket using a cable tie. Do not secure in such a way that it applies strain to the cable, or causes the plug or socket to be bent out of alignment. Connecting power 1234 1 2 3 4 5 + - 6 No.
Connecting touch control The touch screen ZM series monitors can provide touch control to the Zeus2 Processor as well as Windows 7 and Windows 8 PCs. Connection can be made via serial data for Zeus2 Processor or USB for PC systems. Serial connection The ZM series monitors must always be connected to Zeus2 Processor via serial. Make all connections with power turned off. 1234 Zeus2 Processor serial cable No.
Connecting NMEA 2000 When connected to a compatible processor such as the Zeus2 Processor, the display should also be connected to the NMEA 2000 network. This enables the monitors home key to bring up the home screen. NMEA 2000 is also used for applying software updates from the processor to the display. ¼¼ Note: If the monitor is connected to the NMEA 2000 network and the monitor has its key beeps turned on, it will sound for any network alarm when the focus is on that screen.
4 Operating the display The display is configured and controlled using the row of touch sensitive buttons along the lower edge of the monitor frame. All buttons are backlit - only the power button is illuminated when the monitor is turned off. 1. 2. 3. 4. 5. 6. 7. Power: long press turns display on/off.
Option Sub option Setting Scaling HDMI-1 1:1, FILL, ASPECT Sets input image to true size, fill available screen area, or to fill screen vertically or horizontally but maintain correct aspect ratio DVI-2 VID-3 VID-4 Function Option Sub option Range Description Colour Temperature User, 6500K, Allows the user to select colour temperature. 9300K The 6500K setting makes the display colour warmer (slight red tint). The 9300K setting makes the display colour cooler (slight blue tint).
Option Sub option Range Description Slave, Master In slave mode monitor will turn on if 12/24V is detected on the yellow wire.
ZM16: 383mm ZM19: 461mm ZM16: 400mm ZM19: 478mm ZM19: 278mm ZM19: 305mm MAX 25.4 mm (1.00") ZM16: 233mm ZM16: 260mm 5 Dimensional drawings 8 mm (0.31") 66.0 mm (2.60") MAX 88.0 mm (3.
6 Troubleshooting tips Issue Possible Cause No picture - red LED ON LED on continuously indicates no (compatible) video is available on currently selected source. Confirm that the correct video input is selected. Check that the video signal cable is properly connected to the display. Test cable with ‘known good‘ equipment. Check display settings of the video source - ensure the resolution is supported by the display. Ensure brightness is turned up to a suitable level.
7 Cleaning and maintenance If the display requires cleaning, use a damp soft cloth (e.g. microfiber) with a mild, nonabrasive glass cleaner. Ensure cloth is regularly washed or replaced. ¼¼ Note: Do not use paper products as they may scratch the surface. To minimize the risk of abrasion, allow the screen to air dry. ¼¼ Note: Never use acidic, ammonia based, or abrasive cleaning products to clean the display. These products will damage special coatings on the glass.
Replacing the filters Where displays are installed in an unsealed enclosure, air intake filters should be inspected yearly, and replaced if noticeably fouled. If vessel is subject to major works involving spray painting or sanding, it is recommended that the monitor either be removed, or completely covered in a clean fabric drop cloth. ¼¼ Note: ZM16 and ZM19 models require three filter elements. The filter accessory kit includes five elements.
8 General specifications LCD display 15.6” TFT Active Matrix Panel Weight (monitor only): ZM16T = 3.60 kg ZM19T = 4.60 kg 18.
9 Accessories Part description Part number ZM16 bezel trim, silver and black (4 pieces) 000-11620-001 ZM19 bezel trim, silver and black (4 pieces) 000-11621-001 ZM16 Vesa bracket 000-11615-001 ZM19 Vesa bracket 000-11616-001 Cable retention bracket (all models), includes 4 cable ties, screws 000-11614-001 ZM16/19 rear mounting kit 000-11618-001 ZM16/19 dash seal kit (6 pieces) 000-11619-001 ZM16/19 inlet filters (5 pack) 000-11623-001 ZM16/19 inlet filter cover 000-11624-001 HDMI cable
0980 *988-10693-002*