Beo4 Guide
Contents Using your Beo4 remote control, 3 Beo4 buttons in detail, 4 • Daily and advanced operation with Beo4 buttons Customise Beo4, 5 • Add an extra ‘button’ • Move extra ‘buttons’ • Remove an extra ‘button’ • Set up Beo4 • Beo4 zones (ZONE?) • Beo4 options (OPTION?) • Beo4 configuration (VIDEO?) • Beo4 modes (MODE?) • Reset your Beo4 (RESET?) Conversion, 12 Maintenance, 13 • Cleaning Beo4 • Changing the batteries Version 2.
Using your Beo4 remote control 4 5 1 2 6 3 LIST 0 MENU STOP BACK Daily operations are carried out by pressing a single button on Beo4, or by pressing a few buttons in a logical and straightforward sequence. But the Beo4 remote control incorporates more functions than just the actual buttons. Extra sources can be switched on, and additional functions can be obtained via the display. “Buttons” for these functions can be brought up on the Beo4 display via the LIST button.
Beo4 buttons in detail … Move your mouse around this illustration for information about the Beo4 buttons.
Customise Beo4 … The Beo4 buttons give direct remote control of a large number of functions, and the Beo4 display gives you access to even more functions. Whenever a source is displayed on Beo4 (TV, RADIO, etc.), you can press the LIST button and bring up extra functions in the display to help you operate that source, just as if you were bringing up extra buttons. You can also switch on extra equipment connected to your television.
>> Customise Beo4 … Add an extra ‘button’ to Beo4, either to the preset position or to a specific position. 3 Add an extra ‘button’ When you add a new function to the Beo4 list, you can bring up this new ‘button’ in the Beo4 display. > > > > > > > > > Press and hold the standby button down. Press LIST to get access to the Beo4 setup function. Let go of both buttons. ADD? appears in the display.
>> Customise Beo4 … 3 Move extra ‘buttons’, either to the top of the list or to a specific position. Move extra ‘buttons’ You can rearrange the order in which the extra ‘buttons’ appear when you press LIST. > > > > > > > > > > Press and hold the standby button down. Press LIST to get access to the Beo4 setup function. Let go of both buttons. ADD? appears in the display. Press LIST or to display MOVE? on Beo4.
>> Customise Beo4 … Remove an extra ‘button’ You can remove any of the extra ‘buttons’ that are available when you press LIST. > > > > > > Press and hold the standby button down. Press LIST to get access to the Beo4 setup function. Let go of both buttons. ADD? appears in the display. Press LIST or to display REMOVE? on Beo4. Press the centre button and use to select AV?, LIGHT? or CNTROL? Press the centre button to bring up the list of extra ‘buttons’. The first ‘button’ appears in the display.
>> Customise Beo4 … Set up Beo4 If you buy a new Beo4 you can set it up for your television. > > > > > > > > Press and hold the standby button down. Press LIST to get access to the Beo4 setup function. Let go of both buttons. ADD? appears in the display. Press LIST or to display ZONE?, CONFIG? or MODE? on Beo4. Press the centre button to select the setup you want. Press or to display the setting you want on Beo4. Press the centre button to store the configuration.
>> Customise Beo4 … Beo4 options (OPTION?) Appears when you access the Beo4 setup mode. Enables you to preprogram a Bang & Olufsen system setup. V.OPT Video options A.OPT Audio options L.OPT Link options For further information, refer to the guide enclosed with your product. Beo4 configuration (VIDEO?) For selecting a dedicated video product setup for Beo4. VIDEO 5 Supports, for example, video products for the American and European markets.
>> Customise Beo4 … Beo4 modes (MODE?) MODE 1 When a Beo4 remote control is in MODE 1, the navigation button is used for menu operation, and menu and source operation are separated. MODE 1 should be used if: – all your televisions in your video setup contain the ‘REMOTE CONTROL’ or ’BEO4 SETTING’ menu and are set to ‘NAVIGATION BUTTON’. When operating recent televisions without the REMOTE CONTROL/BEO4 SETTING menu, Beo4 must be set to MODE 1.
Conversion … New functions on Beo4 (type 1710) Move your mouse over the highlighted buttons.
Maintenance … CAUTION! Do not expose batteries to excessive heat such as sunshine, fire or the like! 2 1 3 2 1 Cleaning the Beo4 … Wipe the Beo4 remote control with a soft, lint-free, wet cloth which is wrung firmly. Changing the batteries When BATTERY appears in the Beo4 display, it is time to change the batteries in the remote control. The Beo4 requires three batteries (placed under the lid on the back). We recommend that you use 1.5 volt (size AAA) Alkaline batteries only.