owners manual with installation instructions ® TransCommand FORD E4OD/4R100 AUTOMATIC TRANSMISSION EQUIPPED VEHICLES THIS MANUAL IS FOR USE WITH system 62560 & 62570 gale banks engineering 546 duggan avenue • azusa, ca 91702 (626) 969-9600 • fax (626) 334-1743 www.bankspower.com ©2010 gale banks engineering 08/20/10 p.n. 96370 v.3.
Also Available from Banks Power for ‘94-03 Ford 7.3L ‘94-03 Ford 7.
Banks Git-Kit Systems 94-97 (P/N 48550) 99-03 (P/N 47401, 47511-47514) Contains: - Monster Exhaust - Big Hoss Module Banks Stinger Systems 94-97 Contains: - Ram-Air Intake Filter - Monster Exhaust - Big Hoss Module - TransCommand 99-03 Contains: - Ram-Air Intake Filter - Monster Exhaust - Big Hoss Module - Big Head Wastegate Actuator Banks Stinger-Plus Systems 94-97 (P/N 48553-48554, 48559-48560) Contains: - Ram-Air Intake Filter - Monster Exhaust - Big Hoss Module - TransCommand - Quick Turbo Assembly Ban
! Attention TransCommand Owner ® Congratulations on your decision to protect your investment and get the most from your truck or RV! This note has been included to provide you with information concerning the Banks TransCommand on your vehicle. While the Ford E4OD and 4R100 transmissions offer a smooth and comfortable shift, in many cases a more positive shift is necessary.
BILL OF MATERIALS TransCommand Part # Description 62559 62557 62519 62512 91137 91111 91848 62001 62003 96503 96390 96391 MODULE, TransCommand E40D MODULE, TransCommand 4R100 HARNESS, Wire with connector shell and wedge PLUG, Bypass Connector 8 pin BOLT, 1/ ” 28 x 5/ ” Hex 4 8 NUT, 1/ ” 28 Nylock 4 SCREW, Sheet Metal, #14 x 5/ ” Hex WSHR head 8 TIE, Cable, 5” Black TIE, Cable, 15” Black WARRANTY STATEMENT Product Registration Card Product Registration Card 5 System 62560 1 -1 1 2 2 2 3 2 1 1 -- Sys
General Installation Practices For ease of installation of your Banks TransCommand®, familiarize yourself with the procedure by reading the entire manual before starting work. When raising the vehicle, support it on properly weight-rated safety stands, ramps or a commercial hoist. Follow the manufacturer’s safety precautions. Take care to balance the vehicle to prevent it from slipping or falling.
installation procedure Raise the front of vehicle on ramps, jack stands, or a lift if available. DO NOT WORK UNDER ANY VEHICLE SUPPORTED ONLY BY A JACK! 1. NOTE: On vehicles equipped with an E40D, this plug is located behind the small metal shield. Using an 8mm wrench, unbolt this shield to reveal the plug. On vehicles equipped with a 4R100, it may be necessary to unbolt the exhaust heat shielding and slide it out of the way to access the plug. (There is no small metal shield.
FIGURE 3 FRONT VIEW 1994 & EARLIER FRONT VIEW 1995 & LATER NOTE: PINS 1-6 ARE CLOSEST TO TRANSMISSION. PINS 6, 9 & 10 ARE EMPTY. FIGURE 4 A. Insert the red wire with the female socket into pin 1 location of the connector. The locking tang should click into place when the female socket is fully seated. B. Insert the brown wire with the female socket into pin 11. C. Insert the yellow wire with the female socket into pin 12. wedge from front of the connector.
FIGURE 5 Route TransCommand ™ harness along the transmission crossmember and under the frame as shown in Figure 1. Plug the TransCommand ™ wiring harness into the pigtail connector on the TransCommand™. Note: Pin No. 4 hole is not used. 12. 16. Insert the thin end of the supplied red plastic wedge into the front of the connector. Inspect the new connector assembly by double checking the wire colors and pulling on the wires from the rear of the connector to be sure they are fully seated. 13. 14.
TROUBLESHOOTING TIPS Over 90% of problems that occur with TransCommands are related to wiring problems. SYMPTOMS • Normal shifts (no increased pressure) • Very hard shifts • Blinking OD light (which doubles as a check engine light) • The “limp-home” mode (The limp-home mode gives a two speed transmission: second gear in low or second and third gear in drive. The vehicle must be manually shifted from low to drive.) POSSIBLE SOLUTIONS 1.
