Product Description

ManualsBrandsBanlaw ManualsElectronicsHV Dry Break Wireless Swivel Module

RODUCT

ATA

HEET

ANLAW

ECURE

ILL

REAK

UTO

IRELESS

WIVEL

BRT

WSMA

BRT

WSMA

Doc ID: PRH-FMG-76 Version: 0.38

Page 1 of 15

Please ensure you have the latest version of this document.

Thank you for purchasing this high quality Banlaw product. Please read through and understand

the information in this Product Data Sheet (PDS) BEFORE installation or operation of the product

to avoid potential health, safety and environment (HS&E) risks or property damage.

1 PRODUCT DESCRIPTION

figure 1 Banlaw SecureFill Dry Break Auto ID Wireless Swivel (BRT34WSA)

The Banlaw SecureFill Dry-Break Auto ID Wireless Swivel, hereafter referred to as the Wireless Swivel,

represents an innovative evolution of the Banlaw Dry Break “Auto ID” system. The use of wireless

technology provides the same fuel security as the wired FuelTrack Dry-Break Auto ID system with up

to twice the range of the wired Auto ID system.

The Wireless Swivel acts as a conventional swivel and an interface to the ID tag in the attached receiver. The

tag ID is communicated from the Wireless Swivel to the ResTrack System via the Wireless Controller HID. The

use of contact-based identification greatly improves reliability while maintaining security. The Wireless

Swivel is only compatible with Banlaw auto-ID Nozzles, Receivers, and the ResTrack Resource Management

System.

The Wireless Swivel is screwed into the nozzle and provides a rotating mechanical connection between the

hose and the nozzle. The Wireless Swivel detects the ID tag in the receiver and communicates the unique Tag

ID to the ResTrack System via the wireless gateway. The Contact-based identification between the swivel and

the Auto ID receiver greatly improves reliability and security and is fully compatible with previous generation

Banlaw Auto ID nozzles.

The Electronics module (BRTWSM) on the swivel assembly can be replaced when necessary. The Wireless

Swivel is designed for Ultra-low power consumption for extended battery life.

Two LED’s (green & red) on the Wireless Swivel communicate system status to the operator.

The Wireless swivel is compliant with design requirements for Explosive Atmospheres (Hazardous Zones -

ATEX).

Summary of content (15 pages)

PAGE 1
PRODUCT DATA SHEET BANLAW SECUREFILL DRY BREAK AUTO ID WIRELESS SWIVEL BRT33WSMA, BRT34WSMA Thank you for purchasing this high quality Banlaw product. Please read through and understand the information in this Product Data Sheet (PDS) BEFORE installation or operation of the product to avoid potential health, safety and environment (HS&E) risks or property damage.
PAGE 2
BANLAW PRODUCT DATA SHEET Doc ID: PRH-FMG-76 Version: 0.38 Please ensure you have the latest version of this document.
PAGE 3
BANLAW PRODUCT DATA SHEET PRODUCT NAME Operation 1.1 The Wireless Swivel operates continuously and when not in use enters a sleep mode to conserve battery power. An internal accelerometer senses movement and wakes the swivel. The status of the Wireless Swivel can be determined from the two status LEDs visible through the LED status window, see Figure 2 below. Magnet Reset Zone LED Status Window Figure 2 Location of LED status window and magnet reset zone.
PAGE 4
BANLAW PRODUCT DATA SHEET PRODUCT NAME Figure 2). Reset can be verified by viewing the status LEDs. 2 IMPORTANT RESTRICTIONS ON THE USE OF THIS PRODUCT The safe installation and operation of this Banlaw Wireless Swivel rely on the completion of an assessment of the systems suitability for the intended application. This assessment is best achieved through the cooperation of the end-user and Banlaw.
PAGE 5
BANLAW PRODUCT DATA SHEET 3 PRODUCT NAME LOW FREQUENCY RECEIVER AND TRANSMITTER REGULATORY INFORMATION US - FCC Warning Statement FCC ID : 2A28Y-BRTWSMA This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
PAGE 6
BANLAW PRODUCT DATA SHEET PRODUCT NAME Australia and New Zealand Conformance Statement This product conforms to Australia and New Zealand Radio Requirements. Doc ID: PRH-FMG-76 Version: 0.38 Please ensure you have the latest version of this document.
PAGE 7
BANLAW PRODUCT DATA SHEET 4 PRODUCT NAME SPECIFICATIONS Product Name Display Weight RF Frequency Internal Sensors SecureFill Dry Break Auto ID Wireless Swivel 2 status LEDs 1.25 Kg 433 MHZ Accelerometer Magneto resistive sensor (magnetic reset switch) 25 meters (depending on site) 3.6 V Approx. 2 years depending on use -40°C
PAGE 8
BANLAW PRODUCT DATA SHEET 5 PRODUCT NAME CONFIGURATION The Wireless Swivel requires no configuration prior to installation. 5.1 Wireless Swivel - Advanced Controller Registration Step Attach the Wireless Swivel to a FuelTrack nozzle. The LED should blink red. (This indicates the swivel is powered) Figure Attach the nozzle to the receiver (see Blue arrow). The LED will blink green. If the LED is still red actuate the nozzle handle. (This connects the swivel to the nozzle Auto ID button).
PAGE 9
BANLAW PRODUCT DATA SHEET Step Enter a “Super User” Pin number. Select “Done” then “Next”. PRODUCT NAME Figure Select the nozzle that the Wireless Swivel is to control. In this case it will be nozzle 1. Select “Next” The Wireless Swivel’s serial number is shown on the list. Select that serial number and click next to complete the process. Note: If the required number is not displayed refer to the troubleshooting guide. Note: The serial number is marked on the Wireless Swivel.
PAGE 10
BANLAW PRODUCT DATA SHEET Step PRODUCT NAME Figure Apply the “XpressSystemConfig.ini” configuration changes by using the command “ update=B@NlAw,a”. Example “Xpress update=B@NlAw,a” command using Hercules through and port 1004. Xpress will automatically reset after sending the command. Functional Verification Connect Dry-Break nozzle fitted with wireless swivel to a receiver and verify the Xpress detects the receiver ID as shown in the figures.
PAGE 11
BANLAW PRODUCT DATA SHEET Step 6 PRODUCT NAME Figure INSTALLATION GUIDE Prior to commencing the installation conduct a Health Safety and Environment (HS&E, WHS) risk assessment (e.g. SWMS or JHA). For a typical installation, particular attention is drawn to the following areas: • Isolation and bleeding of residual fuel pressure. • Appropriate personal protective equipment (PPE). • Use of appropriate tools and equipment. • Use of trained, qualified and competent personnel.
PAGE 12
BANLAW PRODUCT DATA SHEET PRODUCT NAME Figure 4: Probe extending from the Wireless Swivel. Figure 5: Banlaw FuelTrack nozzle inlet, showing internal data probe contact. Due to the numerous requirements that apply to a Banlaw product, the client shall liaise with Banlaw prior to the use of the product within an application that is deemed to be “uncommon”. The majority of Banlaw clients should already be familiar with Banlaw products, and the applications for which each product/system are suited.
PAGE 13
BANLAW PRODUCT DATA SHEET 7 PRODUCT NAME MAINTENANCE It is typically a legal responsibility of the person(s) who have identified the hazard to isolate the system whose use is likely to result in an unacceptable risk to health, safety and environment. Complete the applicable procedure for the proper and positive isolation of the system and inform worksite management immediately. The scope of this section is restricted to recommended service and maintenance requirements for the Wireless Swivel.
PAGE 14
BANLAW PRODUCT DATA SHEET 8 PRODUCT NAME TROUBLESHOOTING If the Wireless Swivel stops transmitting vehicle’s information, please follow the below troubleshooting guide. ISSUE POSSIBLE SOLUTION(S) No LED activity 1. Wireless Swivel is asleep, move assembly and observe red LED flashes at 1.5 times / second. If there is still no LED activity, then proceed to step 2. No LED activity after 2. If the Wireless Swivel fails to activate after movement, reset movement the Wireless Swivel using a magnet. 3.
PAGE 15
BANLAW PRODUCT DATA SHEET 9 PRODUCT NAME OPTIONAL ACCESSORIES & SPARE PARTS Item/Description Banlaw Part Number Electronics module BRTWSMA Banlaw does not recommend nor endorse the use of non-genuine replacement (spare) parts. The use of spare parts not endorsed by the product OEM is likely to void a product warranty and may jeopardise the safety, performance/function, reliability, and regulatory certifications/approvals of the product.