Cut Sheet

ManualsBrandsBanner Engineering ManualsControl & AutomationMirror/Sensor Stand, 66" Tall

Datasheet

MSA Series Stands for optical safety system sensors or corner mirrors

• Easy to assemble

• Available in

ﬁve pole heights

• Solidly supports emitter, receiver or corner mirror

• Strong extruded and anodized aluminum poles

• Dual-channel design for accurate sensor/mirror adjustment

MSA Series Stands

• Provides mounting T-slots with 20 mm dimension between slots

• Base included. Available without a base by adding the sufﬁx NB to the model

number (for example, MSA-S42-1NB).

Stand Model Pole Height Useable Stand Height Overall Stand Height

MSA-S24-1 610 mm (24 in) 483 mm (19 in) 616 mm (24.25 in)

MSA-S42-1 1067 mm (42 in) 940 mm (37 in) 1073 mm (42.25 in)

MSA-S66-1 1676 mm (66 in) 1550 mm (61 in) 1682 mm (66.25 in)

MSA-S84-1 2134 mm (84 in) 2007 mm (79 in) 2140 mm (84.25 in)

MSA-S105-1 2667 mm (105 in) 2667 mm (100 in) 2673 mm (105.25 in)

(4) M10 Bolt

Pole

40 mm

(1.58") Square

Mounting

Channel

Spacing

20 mm

(0.79")

Useable

Stand

Height

127 mm

(5.0")

Base Plate Thickness

6.4 mm (0.25")

Overview

Banner MSA Series stands are designed speciﬁcally for use with Banner optical safety system emitters and receivers, and corner

mirrors. The poles are constructed of strong, lightweight extruded aluminum, and have a dual-channel design that allows easy and

accurate height adjustment using the supplied “T” nuts.

Each stand includes two major parts:

• Welded steel base

• Aluminum pole: 609.6 mm (24 in), 1066.8 mm (42 in), 1676.4 mm (66 in), 2133.6 mm (84 in), or 2667.0 mm (105 in) long

Hardware is included for attaching the various EZ-SCREEN families or an MSM corner mirror to the pole. The SGS Grids, EZ-

SCREEN points and SSM Series mirrors require the EZA-MBK-2 adapter bracket. A post level is included with each stand for

accurate installation.

MSA Series Stand

Original Document

43687 Rev. D

12 March 2019

43687

Summary of content (4 pages)

PAGE 1
MSA Series Stand Datasheet MSA Series Stands for optical safety system sensors or corner mirrors • Easy to assemble • Available in five pole heights • Solidly supports emitter, receiver or corner mirror • Strong extruded and anodized aluminum poles • Dual-channel design for accurate sensor/mirror adjustment MSA Series Stands • • Mounting Channel Spacing 20 mm (0.79") Provides mounting T-slots with 20 mm dimension between slots Base included.
PAGE 2
MSA Series Stand The pole is held securely in its base by four bolts (included). The base bolts to a flat surface with user-supplied 5/16" or M8 hardware. The base plate has four threaded holes for leveling bolts. The mounting design allows the sensor or mirror to easily slide up or down the pole and then lock into position by tightening four screws.
PAGE 3
MSA Series Stand 2. Assemble the brackets and hardware as shown in the appropriate figure. Figure 2. Adapter bracket-to-stand mounting, shown ready for mounting of SSM series mirror Figure 3. MSM Series mirror to stand mounting Stand Pole M4 Screw and “T” nut Bracket Stand Pole M4 Screw and "T" Nut (8 supplied with stand; use as needed) Bracket (2 supplied with sensor) 2x M5 Screw (supplied with sensor) LP Light Screen EZ-SCREEN 14/30 (or standard) (emitter/receiver) Figure 4.
PAGE 4
MSA Series Stand 3. Loosely mount the bracket assemblies to the pole using the M4 screws and “T” nuts supplied with the stand. Note that all figures show the bracket assembly pointed out (away from the sensor or mirror). One or both of the bracket assemblies may be reversed to point in, if necessary. However, access to the mounting screws becomes less convenient and mirror rotation is limited when a bracket assembly is pointed in. 4.