Cut Sheet

Specicaons
Supply Voltage and Current
Q60BB6LAF models: 10 to 30 V dc (10% maximum ripple) at less than 50 mA
exclusive of load
Q60VR3LAF Universal models: 12 to 250 V dc or 24 to 250 V ac, 50/60 Hz
Input power: 1.5 W maximum
Supply Protecon Circuitry
Protected against reverse polarity and transient voltages
The dc wiring for model Q60VR3 is without regard to polarity
Output Conguraon
Q60BB6LAF models: Bipolar; one NPN (current sinking) and one PNP (current
sourcing) open-collector transistor
Q60VR3LAF cabled model: E/M Relay (SPDT), normally closed and normally
open contacts
Q60VR3LAFQ1 (QD) model: E/M Relay (SPST), normally open contact
Output Rang—Q60BB6LAF models
150 mA maximum each output @ 25 °C
O-state leakage current: < 5 μA @ 30 V dc
Output saturaon NPN: < 200 mV @ 10 mA and < 1 V @150 mA
Output saturaon PNP: < 1 V at 10 mA; < 1.5 V at 150 mA
Output Rang—Q60VR3LAF Universal models
Minimum voltage and current: 5 V dc, 10 mA
Mechanical life of relay: 50,000,000 operaons
Electrical life of relay at full resisve load: 100,000 operaons
Maximum switching power (resisve load):
Cabled models: 1250 VA, 150 W
QD models: 750 VA, 90 W
Maximum switching voltage (resisve load):
Cabled models: 250 V ac, 125 V dc
QD models: 250 V ac, 125 V dc
Maximum switching current (resisve load):
Cabled models: 5 A @ 250 V ac, 5 A @ 30 V dc derated to 200 mA @ 125 V
dc
QD models: 3 A @ 250 V ac, 3 A @ 30 V dc derated to 200 mA @ 125 V dc
Output Protecon Circuitry
Q60BB6LAF models: Protected against connuous overload or short circuit of
outputs
All models: Protected against false pulse on power-up
Note: 1 second maximum delay at power up
(outputs do not conduct during this me)
Output Response Time
Q60BB6LAF models: 2 milliseconds ON and OFF
Q60VR3LAF Universal models: 15 milliseconds ON and OFF
Repeatability
500 microseconds
Sensing Hysteresis
See Figure 11 on page 5
Laser Characteriscs
Spot Size:
approximately 4 × 2 mm throughout range (collimated beam)
Angle of Divergence: 5 milliradians
Note: Contact Banner Engineering for a custom
laser spot size.
Adjustments
Sloed, geared, 2-turn, cuto range adjustment screw (mechanical stops on
both ends of travel)
2 momentary push buons: ON Delay (+) and OFF Delay (–); DC models also
have a remote program wire
ON Delay select: 8 ms to 16 seconds
OFF Delay select: 8 ms to 16 seconds
LO/DO select
Push buon lockout for security
Laser Enable/Disable (remote wire only)
Construcon
Housing: ABS polycarbonate blend
Lens: Acrylic
Environmental Rang
IEC IP67; NEMA 6
Connecons
Q60BB6LAF models: 2 m (6.5 ) or 9 m (30 )
aached cable, 5-pin Euro-style
integral QD, or 5-pin Euro-style 150 mm (6 in) QD
Q60VR3LAF Universal models: 2 m (6.5 ) or 9 m (30 ) aached cable, or 5-
pin Micro-style 150 mm (6 in) QD
Operang Condions
Temperature:
Q60BB6LAF models: −10 °C to +50 °C (+14 °F to +122 °F)
Q60VR3LAF Universal models: −10 °C to +45 °C (+14 °F to +113 °F)
90% at +50 °C maximum relave humidity (non-condensing)
Required Overcurrent Protecon
WARNING: Electrical connecons must be made
by
qualied personnel in accordance with local
and naonal electrical codes and regulaons.
Overcurrent protecon is required to be provided by end product applicaon
per the supplied table.
Overcurrent protecon may be provided with external fusing or via Current
Liming, Class 2 Power Supply.
Supply wiring leads < 24 AWG shall not be spliced.
For
addional product support, go to www.bannerengineering.com.
Supply Wiring (AWG) Required Overcurrent Protecon (Amps)
20 5.0
22 3.0
24 2.0
26 1.0
28 0.8
30 0.5
Cercaons
Q60LAF Series Laser Adjustable-Field Sensors
P/N 114348 Rev. A www.bannerengineering.com - Tel: [phone]