Cut Sheet

ManualsBrandsBanner Engineering ManualsBackground Rejection SensorsSelf-Contain Adjust-Field, 70095

Datasheet

Self-Contained Adjustable-Field Sensors

• Adjustable-eld background suppression sensor detects objects within a dened

sensing eld, while ignoring objects located beyond the sensing eld

cuto

• Two-turn, logarithmic adjustment of sensing eld cuto point from 0.2 m to 1 m (7.9

in to 3.3 ); allows easy seng of cuto point at long range

• Rotang pointer indicates relave

cuto point seng

• Easy

push-buon or remote programming of light/dark operate and output ming;

connuous status indicators verify all sengs at a glance

• Output ON and/or OFF delays adjustable from 8 milliseconds to 16 seconds

• Powerful, highly collimated visible red sensing beam

• Tough ABS/polycarbonate blend housing is rated IEC IP67; NEMA 6

10 to 30 V dc Models (Q60BB6AFV):

• Powered by 10 to 30 V dc; bipolar (one NPN and one PNP) outputs

• Available with integral cable or rotang Euro-style quick-disconnect ng

Universal Voltage Models (Q60VR3AFV):

•

12 to 250 V dc or 24 to 250 V ac, 50/60 Hz

• Available with integral cable or rotang Micro-style quick-disconnect ng

WARNING: Not To Be Used for Personnel Protecon

Never use this device as a sensing device for personnel

protecon. Doing so could lead to serious injury or

death. This device does not include the self-checking redundant circuitry necessary to allow its use in personnel

safety applicaons. A sensor failure or malfuncon can cause either an energized or de-energized sensor output

condion.

Models

Models Minimum Range Cuto Point Cable

Supply Voltage Output Type

Q60BB6AFV1000

65 mm to 130 mm (2.5 in

to 5 in) depending on

cuto point seng

Adjustable:

200 mm to 1000 mm (8 in

to 40 in)

5-wire 2 m (6.5 )

10 V dc to 30 V dc Bipolar NPN/PNP

Q60BB6AFV1000Q 5-pin Euro-style QD

Q60VR3AFV1000 5-wire 2 m (6.5 )

Universal Voltage

12 V dc to 250 V dc

24 V ac to 250 V ac

E/M Relay (SPDT),

normally closed and

normally open contacts

Q60VR3AFV1000Q1 4-pin Micro-style QD

E/M Relay (SPST),

normally open contact

Overview

The A60AFV sensor is a full-featured adjustable-eld sensor. These adjustable-eld sensors are able to detect objects of relavely low

reecvity, while ignoring other objects in the background (beyond the cuto point). The cuto distance is mechanically adjustable,

using the 2-turn adjustment screw on the top of the sensor. A rotang pointer indicates the relave

cuto posion. The indicator moves

clockwise to show increasing distance.

Two push buons (ON Delay and OFF Delay) are used to set the output delay opons, to toggle between light and dark operate modes

and to lock out the push buons for security purposes. These funcons also may be accomplished using the remote wire (available on

some models).

Seven LED indicators show, during RUN mode, the sensor conguraon and operang status. During Delay Conguraon, 5 of the LEDs

combine to form a single light bar that indicates relave ON or OFF delay me.

Note: When an object approaches from the side, the most reliable sensing usually occurs when the line of approach

is parallel to the sensing axis.

To order the 9 m (30 ) PVC cable model, add the sux "W/30" to the cabled model number. For example, Q60BB6AFV1000 W/30. Models with a quick

disconnect require a mang cordset.

Q60AFV Series Sensors with Visible Red Emier

Original Document

69622 Rev. C

10 February 2017

69622

Summary of content (11 pages)

PAGE 1
Q60AFV Series Sensors with Visible Red Emitter Datasheet Self-Contained Adjustable-Field Sensors • • • • • • • Adjustable-field background suppression sensor detects objects within a defined sensing field, while ignoring objects located beyond the sensing field cutoff Two-turn, logarithmic adjustment of sensing field cutoff point from 0.2 m to 1 m (7.9 in to 3.
PAGE 2
Q60AFV Series Sensors with Visible Red Emitter Features and Indicators Note: Outputs are active during on/off timing selection mode.
PAGE 3
Q60AFV Series Sensors with Visible Red Emitter Installation Wiring Diagrams Q60BB6xx(Q) Q60VR3xx Cabled and QD Models, 10 to 30 V dc Cabled Model, 24 to 250 V ac (50/60Hz) or 12 to 250 V dc 1 3 2 4 1 + 10-30V dc – 3 2 C 4 Load 5 N.C. 5 Load Key 24 - 250V ac or 12 - 250V dc N.O. 1 = Brown 2 = White 3 = Blue 4 = Black 5 = Gray Remote Program Q60VR3xxQ1 QD Model, 24 to 250 V ac (50/60Hz) or 12 to 250 V dc Key 1 24-250V ac or 12-250V dc* 2 3 N.O.
PAGE 4
Q60AFV Series Sensors with Visible Red Emitter Sensing Reliability For highest sensitivity, the sensor-to-object distance should be such that the object will be sensed at or near the point of maximum excess gain. The excess gain curves show excess gain versus sensing distance for 200 mm and 1 m cutoffs. Maximum excess gain for a 200 mm cutoff occurs at a lens-to-object distance of about 150 mm, and for a 1 m cutoff, at about 400 mm. The background must be placed beyond the cutoff distance.
PAGE 5
Q60AFV Series Sensors with Visible Red Emitter The percentage of deviation indicates a change in the cutoff point for either 18% gray or 6% black targets, relative to the cutoff point set for a 90% reflective white test card. Minimum Range with a 6% Black Card (mm) For example, the cutoff point decreases 4% for a 6% reflectance black target when the cutoff point is adjusted for 1000 mm (40 in) using a 90% reflectance white test card.
PAGE 6
Q60AFV Series Sensors with Visible Red Emitter Increase or Decrease the ON Delay T = 40 – 800 ms Press and Hold > 800 ms unless otherwise noted Increase the ON Delay—4-second time-out Enter ON Delay Setup Enable Delay Increment Single-Click Push Button ON DELAY + >800 ms Rapid Decrement Press and Hold Single-Click ON + DELAY – DELAY OFF ON DELAY + – OFF DELAY + T >800 ms T T T >800 ms – Step Decrement ON T >800 ms DELAY T >800 ms DELAY – OFF DELAY Remote Input N/A Press
PAGE 7
Q60AFV Series Sensors with Visible Red Emitter LO/DO Toggle Remote Input >4 sec. Lock the Push Buttons For security, the push buttons can be locked out using either the remote line or the push buttons themselves. Push Button Lockout Toggle Concurrent Quad-Click ON DELAY – + P/N 69622 Rev. C DELAY Remote Input OFF Push Button T T T T T T T >800 ms www.bannerengineering.
PAGE 8
Q60AFV Series Sensors with Visible Red Emitter Specifications Supply Voltage and Current Q60BB6AFV models: 10 to 30 V dc (10% maximum ripple) at less than 50 mA exclusive of load Q60VR3AFV Universal models: 12 to 250 V dc or 24 to 250 V ac, 50/60 Hz Supply Protection Circuitry Protected against reverse polarity and transient voltages The dc wiring for model Q60VR3 is without regard to polarity Output Configuration Q60BB6AFV models: Bipolar; one NPN (current sinking) and one PNP (current sourcing) open-coll
PAGE 9
Q60AFV Series Sensors with Visible Red Emitter Dimensions 15.2 mm (0.60") 4.0 mm (0.16") 4.9 mm (0.19") – DELAY OFF LO SIG + ON DO RANGE 25.0 mm (0.98") DELAY 60.0 mm (2.36") 52.0 mm (2.05") 4.0 mm (0.16") 2x ø4.2 mm (0.17") 14.0 mm (0.55") Q60BB6AFV200 75.0 mm (2.95") 52.0 mm (2.05") bn 67.0 mm (2.64") bu wh bk Q60BB6AFV200Q bn + 10-30V dc – + 10-30V dc – bu wh Load bk Load gy gy Remote Teach Load Load Remote Teach M3 hardware is included 17.0 mm (0.67") 77.6 mm (3.
PAGE 10
Q60AFV Series Sensors with Visible Red Emitter Accessories Cordsets 4-Pin Micro-Style Cordsets Model Length MQAC-406 1.83 m (6 ft) MQAC-415 4.57 m (15 ft) Style Dimensions Pinout (Female) 42 Typ. Straight MQAC-430 1/2-20 UNF-28 ø 14.5 9.14 m (30 ft) MQAC-406RA 1.83 m (6 ft) MQAC-415RA 4.57 m (15 ft) 2 32 Typ 9.14 m (30 ft) 4 1 1 = Red/Black 2 = Red/White 3 = Red 4 = Green 28 Typ Right-Angle MQAC-430RA 3 1/2-20 UNF-28 ø 14.
PAGE 11
Q60AFV Series Sensors with Visible Red Emitter Banner Engineering Corp. Limited Warranty Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period.