Cut Sheet

ManualsBrandsBanner Engineering ManualsControl & AutomationLong Range Laser Sensor Receiver, 18M

Datasheet

Polarized Retroreflective Laser Sensors

• Visible class 1 laser with small, effective beam size

• Excellent optical performance throughout sensing range, even

close up

• Easy push-button SET options: Maximum Excess Gain or Low-

Contrast SET, depending on model, plus Manual Adjust

• Easy-to-read operating status indicators, with 8-segment bar

graph display

• Bipolar discrete outputs, PNP and NPN

• Selectable 30 millisecond OFF-delay

• Models available with 2 m or 9 m (6.5 ft or 30 ft) cable or integral

quick-disconnect

• Tough ABS housing rated IEC IP67; NEMA 6

• Compact housing, mounting versatility – popular 30 mm threaded

nose or side-mount

Excellent for applications where high sensing power and small beam size are important. Operates over sensing ranges

typically accomplished only by conventional opposed-mode photoelectrics; uses a special filter to polarize the emitted light,

filtering out unwanted reflections from shiny objects.

WARNING: Not To Be Used for Personnel Protection

Never use this device as a sensing device for personnel protection. Doing so could lead to

serious injury or death. This device does not include the self-checking redundant circuitry necessary

to allow its use in personnel safety applications. A sensor failure or malfunction can cause either an

energized or de-energized sensor output condition.

Models

Model

Range and Use Spot Size at

Focus

Cable

Supply Output

Type

QS30LLP 0.2 m to 18 m (0.67 ft to

60 ft) Maximum Excess

Gain SET for Long-Range

Applications

Approx. 4 mm at

10 m (0.16 in at 33

ft)

2 m (6.5 ft) 5-wire Cable

10 V dc

to 30 V

Bipolar

NPN / PNP

QS30LLPQ Integral 5-pin Euro-style QD

QS30LLPC 0.2 m to 18 m (0.67 ft to

60 ft) Low-Contrast SET

for Small Object Detection

2 m (6.5 ft) 5-wire Cable

QS30LLPCQ Integral 5-pin Euro-style QD

Overview

QS30LLP and QS30LLPC Series sensors are easy-to-use, high-performance laser sensors whose many configuration

options make them suitable for demanding applications. Each sensor features two identically configured outputs, one each

NPN and PNP.

The compact housing has a large, easy-to-see bar graph display plus bright LEDs for easy configuration and status

monitoring during operation. The sensor can be side-mounted, using integral mounting holes, or front-mounted, via the 30

mm threaded barrel.

MODEL QS30LLP(Q) is configured using the Maximum Excess Gain SET procedure. It is useful for long-range applications

and high variations in contrast, such as beam-break applications where the target objects are larger than the beam. See

Maximum Excess Gain SET - Model QS30LLP on page 4 for more information.

To order the 9 m (30 ft) cable models, add the suffix “W/30” to the model number of any cabled sensor (for example, QS30LLP W/30). A model with a QD

connector requires a mating cable.

WORLD-BEAM QS30 LLP and LLPC

Original Document

112355 Rev. E

15 December 2016

112355

Summary of content (11 pages)

PAGE 1
WORLD-BEAM QS30 LLP and LLPC Datasheet Polarized Retroreflective Laser Sensors • • • • • • • • • Visible class 1 laser with small, effective beam size Excellent optical performance throughout sensing range, even close up Easy push-button SET options: Maximum Excess Gain or LowContrast SET, depending on model, plus Manual Adjust Easy-to-read operating status indicators, with 8-segment bar graph display Bipolar discrete outputs, PNP and NPN Selectable 30 millisecond OFF-delay Models available with 2 m or 9
PAGE 2
WORLD-BEAM QS30 LLP and LLPC MODEL QS30LLPC(Q) is configured using the Low-Contrast SET procedure. It is useful for small object detection and other applications with small variations in contrast, such as yarn- or thread-break applications. See Low-Contrast SET Model QS30LLPC on page 5 for more information.
PAGE 3
WORLD-BEAM QS30 LLP and LLPC Ø = Misalignment Angle Y Y = X(tan Ø) Sensing Distance = X Figure 3. Beam Displacement per degree of misalignment Sensor-to-Target Distance (X) Beam Displacement (Y) for 1º of Misalignment 1.
PAGE 4
WORLD-BEAM QS30 LLP and LLPC Wiring Diagrams Cabled Models brown blue white black gray QD Models brown + 10-30 V dc – Load Load + 10-30 V dc – blue white 150 mA maximum load Load black Load gray Remote TEACH 150 mA maximum load Remote TEACH Note: The pink wire is not used. Sensor Configuration Configure the sensor using the SET and SETUP modes. After SET mode has defined the sensing parameters, use SETUP mode to add an OFF-delay or change the light/dark operate status.
PAGE 5
WORLD-BEAM QS30 LLP and LLPC gain, pressing “–” once lowers the gain to 6X, exhibited by LED #8 ON. Pressing it twice more results in approximately 5X excess gain, exhibited by LED #7 ON. Holding the “+” button for 2 seconds results in a return to maximum gain (20X), exhibited by LEDs #7 and 8 flashing.
PAGE 6
WORLD-BEAM QS30 LLP and LLPC Set Switchpoint Method Push Button Action Result a. Align sensor to the reflector. Green Power LED: OFF Amber Output LED: ON b. Press and hold "+" > 2 seconds.
PAGE 7
WORLD-BEAM QS30 LLP and LLPC Method Action Result Green Power LED turns OFF Push Button4 Press and hold both push buttons > 2 seconds — GAIN + 2. Select SETUP Options. Method Action Result DO, No Delay DO 30 ms Delay — Push Button Click either push button to toggle through the four possible setting combinations. + — + — + or LO, 30 ms Delay — LO, No Delay + 3. Return to RUN Mode.
PAGE 8
WORLD-BEAM QS30 LLP and LLPC Specifications Supply Voltage and Current 10 V dc to 30 V dc (10% maximum ripple at 10% duty cycle) at 35 mA maximum current, exclusive of load Sensing Beam Visible red LED, 650 nm Laser Classification Class 1 Adjustments 2 push buttons and remote wire Easy push-button configuration Manually adjust (+/-) thresholds (push buttons only) LO/DO and OFF-delay configuration options Push-buttons lockout (from remote wire only) Factory Defaults: Beam Size at Aperture Approximately 3
PAGE 9
WORLD-BEAM QS30 LLP and LLPC Dimensions Cabled Models QD Models 35.0 mm (1.38") 22.0 mm (0.87") 32.5 mm (1.28") 1.3 mm (0.05") 12.5 mm (0.49") 3.5 mm (0.14") 8 7 6 5.0 mm (0.20") 44.0 mm (1.73") 33.0 mm (1.30") 5 4 3 2 1 M30 x 1.5 Thread max. torque 6 Nm (53 in lbs) with included 30 mm mounting nut 2 x ø3.3 mm (0.125") max. torque 0.7 Nm (6 in lbs) 13.0 mm (0.51") Hardware Included: (2) M3 × 0.
PAGE 10
WORLD-BEAM QS30 LLP and LLPC Accessories Quick-Disconnect Cables 5-Pin Threaded M12/Euro-Style Cordsets—Single Ended Model Length MQDC1-501.5 Style Dimensions 0.50 m (1.5 ft) MQDC1-506 1.83 m (6 ft) MQDC1-515 4.57 m (15 ft) MQDC1-530 9.14 m (30 ft) MQDC1-506RA MQDC1-515RA 44 Typ. Straight M12 x 1 ø 14.5 2 1 3 1.83 m (6 ft) 4 32 Typ. [1.26"] 4.57 m (15 ft) 30 Typ. [1.18"] Right-Angle MQDC1-530RA Pinout (Female) 9.
PAGE 11
WORLD-BEAM QS30 LLP and LLPC Brackets SMB30SC • Swivel bracket with 30 mm mounting hole for sensor • Black reinforced thermoplastic polyester • Stainless steel mounting and swivel locking hardware included 67 B 58 29 SMBQS30L • Right-angle bracket for cable sensor models • Clearance for M4 (#8) hardware • ± 12° tilt adjustment • 14-ga. stainless steel A Hole center spacing: A=ø 50.8 Hole size: A=ø 7.0, B=ø 30.0 Hole center spacing: A to B=35.0 Hole size: A=ø 4.3, B=ø 4.25x16.