Cut Sheet

Specifications
Supply Voltage and Current
10 V dc to 30 V dc (10% maximum ripple at 10% duty cycle) at 35 mA
maximum current, exclusive of load
Sensing Beam
Visible red LED, 650 nm
Laser Classification
Class 1
Beam Size at Aperture
Approximately 3 mm
Supply Protection Circuitry
Protected against reverse polarity, overvoltage, and transient voltages
Delay at Power-Up
1 second maximum; outputs do not conduct during this time
Output Configuration
Solid-state bipolar (SPDT): 1 current sourcing (PNP) and 1 current
sinking (NPN)
Output Rating
150 mA maximum load
Off-state leakage current: < 10 µA at 30 V dc
ON-state saturation voltage:
NPN: less than 1.0 V at 150 mA load
PNP: less than 2.0 V at 150 mA load
Output Protection Circuitry
Protected against output short-circuit, continuous overload, transient
overvoltages, and false pulse on power-up
Output Response
500 microseconds
Repeatability
70 microseconds
Required Overcurrent Protection
WARNING:
Electrical connections must be
made by qualified personnel in accordance
with local and national electrical codes and
regulations.
Overcurrent protection is required to be provided by end product
application per the supplied table.
Overcurrent protection may be provided with external fusing or via
Current Limiting, Class 2 Power Supply.
Supply wiring leads < 24 AWG shall not be spliced.
For additional product support, go to www.bannerengineering.com.
Supply Wiring (AWG)
Required Overcurrent Protection (Amps)
20 5.0
22 3.0
24 2.0
26 1.0
28 0.8
30 0.5
Adjustments
2 push buttons and remote wire
Easy push-button configuration
Manually adjust (+/-) thresholds (push buttons only)
LO/DO and OFF-delay configuration options
Push-buttons lockout (from remote wire only)
Factory Defaults:
No Delay
Dark Operate
Push buttons enabled
Indicators
Green LED: Power ON
Amber LED: Output conducting
8-Segment Red Bar Graph
SETUP mode:
LED 3 (clock): Flashes Red when delay is selected
LED 2 (DO): Flashes Red when Dark Operate is selected
LED 1 (LO): Flashes Red when Light Operate is selected
RUN mode: Signal Strength (excess gain), relative to switchpoint
Model QS30LLP Model QS30LLPC
LED 8: >6X LED 8: >2X
LED 7: 5-6X LED 7: 1.5-2X
LED 6: 4-5X LED 6: 1-1.5X
LED 5: 3-4X LED 5: 0.8X
LED 4: 2-3X LED 4: 0.6X
LED 3: 1-2X LED 3: 0.4X
LED 2: 0.5-1X LED 2: 0.2X
LED 1: 0-0.5X LED 1: 0X
Sensor calibration failure: Alternating even-numbered and odd-
numbered LEDs flash
Construction
ABS housing, acrylic lens cover
Environmental Rating
IEC IP67; NEMA 6
Connections
5-conductor 2 m (6.5 ft) PVC cable, 9 m (30 ft) PVC cable, or 5-pin
integral M12/Euro-style male quick-disconnect fitting
Operating Conditions
−10 °C to +50 °C (+14 °F to +122 °F)
95% at +50 °C maximum relative humidity (non-condensing)
Vibration and Mechanical Shock
All models meet Mil Std. 202F requirements. Method 201A (vibration:
10 Hz to 60 Hz max., double amplitude 0.06 inch, maximum
acceleration 10G). Also meets IEC 947-5-2 requirements: 30G 11 ms
duration, half sine wave.
Certifications
WORLD-BEAM QS30 LLP and LLPC
8 www.bannerengineering.com - Tel: [phone] P/N 112355 Rev. E