Instruction Manual
Table Of Contents
- Contents
- 1 The Sure Cross® Wireless Network
- 2 Features
- 3 Setting Up Your Wireless Network
- 3.1 Mixing Performance and Non-Performance (150 mW) Radios in the Same Network
- 3.2 Apply Power to the Gateway or Node
- 3.3 Bind Radios to Form Networks
- 3.4 LED Behavior for the Gateways
- 3.5 LED Behavior for the Nodes
- 3.6 Conducting a Site Survey (Gateway and Nodes)
- 4 Installing Your Sure Cross® Radios
- 5 Advanced Setup Options
- 5.1 DX80 Menu Structure
- 5.2 Web-based Configuration for the GatewayPro on DX83
- 5.3 Binding Mode: What does it do?
- 5.4 Setting the Network ID in Extended Addressing Mode
- 5.5 Manually Assign a Binding Code to a Gateway
- 5.6 Manually Assign a Binding Code to a Node
- 5.7 Setting the Maximum System Devices
- 5.8 Storage and Sleep Modes
- 5.9 Modbus Holding Registers
- 5.10 Modbus Communication Parameters
- 5.11 Default Output Conditions
- 5.12 Defining the Units
- 6 Product Support and Maintenance
- Index
Host
1
2
3
4
5
1. Ethernet crossover cable using the Modbus/TCP or
EtherNet/IP communication protocol
2. Power connection
3. DX83 Ethernet Bridge
4. Splitter cable CSRB-M1250M125.47M125.73 using
Modbus RTU
5. Gateway
Typically, the Modbus RTU connection at a GatewayPro is not used because the GatewayPro contains a master and slave
device. The Modbus RTU factory default settings for a standard Gateway are: 19200 baud; 8 data bits; No stop bits; 1 parity
bit; Modbus Slave ID 1.
5.2.1 Accessing the Web-based
Configuration Screens
The configuration Web pages are served from the DX83 Ethernet Bridge or GatewayPro and are accessed using any
Internet browser.
Before accessing the Web-based configuration screens, configure the browser for a direct connection to the Internet. If you
are experiencing problems connecting, verify the browser is not set to use a proxy server. Use a crossover Ethernet cable
when connecting directly from a host computer to the DX83 Ethernet Bridge or GatewayPro; use a standard Ethernet cable
when connecting through a switch or Ethernet hub.
The factory default IP address for the DX83 Ethernet Bridge or GatewayPro is: 192.168.0.1 To change the default IP
address, set up the host PC with an IP address different from the Ethernet Bridge or GatewayPro IP addresses. (Refer to
Banner document p/n 133116 for detailed instructions on setting up the host computer’s network IP address.) For example,
change the PC host IP address to: 192.168.0.2. To access the
configuration screens, follow these steps.
1. Open a Web browser and log into the Ethernet Bridge or GatewayPro by typing the IP address in the browser
location window: http://192.168.0.1.
The Web home page for the Ethernet Bridge or GatewayPro displays.
2. Click on any tab at the top of page to log into the
configuration software.
3. Enter system as the user name and admin as the password.
After making your changes and saving the
file, close the browser to log out of the configuration system.
5.2.2 Changing the IP Address
Use the page tabs at the top of the page to select the hierarchical path: System > Setup > Network . To change the IP
address, type in the new IP address and click the Change IP button. The IP address change activates when the Ethernet
Bridge or GatewayPro reboots (cycles power).
Sure Cross
®
Performance DX80 Wireless I/O Networks
38 www.bannerengineering.com - Tel: + 1 888 373 6767