Owner manual

ManualsBrandsBanner ManualsSensorsD11 Series

D11 Series

Low cost self-contained sensors for use with plastic fiber optics

Printed in USA P/N 44277L7A

• Low cost, 10 to 30V dc self-contained sensors for use with all Banner

plastic fiber optics

• Compact 11 mm-wide housing designed for DIN rail mounting; can also

be mounted to any surface using the supplied mounting bracket

• Choice of NPN (sinking) or PNP (sourcing) complementary outputs -

one normally open and one normally closed; 150 mA output load rating

• Normally-closed output may be wired as a diagnostic alarm to alert

personnel to marginal sensing conditions

†

• Fast, 500 microsecond (0.5 millisecond) output response

• LED status indications for Power On, Output Overload, Fiber Alignment,

and Marginal Gain Conditions

• Choose models with integral 2 m (6.5 ft) cable or pico-style quick

disconnect (QD) connector; 9 m (30 ft) cables are also available

†

U.S. Patent #5087838

Features

D11 Series

Models

Range Cable

Supply

Voltage

Output

Type

Range Specifications

D11SN6FP

D11SN6FPQ

Range

varies

sensing

mode

and fiber

optics

used

2 m (6.5 ft)

4-pin Pico QD

10-30V dc

Comple-

mentary

NPN

(sinking)

D11SP6FP

D11SP6FPQ

2 m (6.5 ft)

4-pin Pico QD

Comple-

mentary

PNP

(sourcing)

Notes:

1) 9 m (30 ft) cables are available by adding suffix "W/30" to the model number of any cabled sensor (e.g. D11SN6FP W/30).

2) A model with a QD connector requires an optional mating cable.

100

10 mm

0.4 in

100 mm

4.0 in

1000 mm

40 in

1.0 mm

0.04 in

1000

DISTANCE

D11 Series

Opposed Mode

Plastic Fibers

PIT46U

Fibers

PIT26U

Fibers

Diffuse mode performance based on 90% reflectance white test card

100

1.0 mm

0.04 in

10 mm

0.4 in

100 mm

4 in

0.1 mm

0.004 in

1000

DISTANCE

D11 Series

Diffuse Mode

Plastic Fibers

PBT46U

Fiber

PBT26U

Fiber

Summary of content (4 pages)

PAGE 1
D11 Series Low cost self-contained sensors for use with plastic fiber optics Features • Low cost, 10 to 30V dc self-contained sensors for use with all Banner plastic fiber optics • Compact 11 mm-wide housing designed for DIN rail mounting; can also be mounted to any surface using the supplied mounting bracket • Choice of NPN (sinking) or PNP (sourcing) complementary outputs one normally open and one normally closed; 150 mA output load rating • Normally-closed output may be wired as a diagnostic alarm to al
PAGE 2
D11 Series DC Product Specifications Required Fiber Optic Cable PI or PB Series plastic fibers Sensing Beam Visible red, 680 nm Supply Voltage and Current 10 to 30V dc at 25 mA (exclusive of load current) Supply Protection Circuitry Protected against reverse polarity and transient voltages Output Configuration Complementary: one normally open (N.O.) and the other normally closed (N.C.); N.C.
PAGE 3
D11 Series Hookup Diagrams Sensors with NPN (Sinking) Outputs Sensors with PNP (Sourcing) Outputs Standard Hookup bu bn bk wh Standard Hookup bn bu bk wh - 10-30V dc + Load Load Alarm Hookup + 10-30V dc - Load Load Alarm Hookup bn bu bk wh bu bn bk wh - 10-30V dc + Load Alarm + 10-30V dc - Load Alarm Note: Connections are the same for either an integral cable or QD cable.
PAGE 4
D11 Series Dimensions Plastic Fiber Installation: Slide Up to Release Fibers Cabled models Sensitivity Adjustment Power Indicator Output Indicator Cut fiber ends per instructions included with the fibers. Slide the fiber gripper up (open). For 0.25 mm or 0.5 mm diameter fibers, insert the adapter (shown below) into the ports as far as it will go. 2. All fibers: Insert the prepared plastic fiber sensor ends gently into the ports as far as they will go. 3. Slide the fiber gripper back down to lock.