Owner manual

ManualsBrandsBanner ManualsSensorsD11 Series

D11 Expert Series – 5V dc Models

Low cost teach-mode sensors for use with plastic fiber optics

Printed in USA P/N 46487

D11E Series – 5V dc Models

Models

Range Cable

Supply

Voltage

Output

Type

Maximum Range Specifications

D11EN72FP

D11EN72FPQ

Range

varies

sensing

mode

and fiber

optics

used

2 m (6.5 ft)

4-pin Pico QD

4.5-5.5V dc

NPN

(sinking)

TTL

Compatible

D11EP72FP

D11EP72FPQ

2 m (6.5 ft)

4-pin Pico QD

PNP

(sourcing)

Notes:

1) 9 m (30 ft) cables are available by adding suffix "W/30" to the model number of any cabled sensor (e.g. D11EN72FP W/30).

2) A model with a QD connector requires an optional mating cable (see page 6).

Diffuse mode performance based on 90% reflectance white test card

• Low cost, 5V dc self-contained TEACH mode sensors for use with all

Banner plastic fiber optics

• Compact 11 mm-wide housing designed for DIN rail mounting; can also

be mounted to any surface using the supplied mounting bracket

• Easy push button TEACH mode programming automatically adjusts

sensitivity to optimal setting

• Designed for high-performance, even in low-contrast sensing applications

• Fast, 200 microsecond (0.2 millisecond) output response; a 40

millisecond output pulse stretcher may be programmed, when needed

• Choose models with NPN (sinking) or PNP (sourcing) output

• Output may be programmed for either light or dark operate

• Separate input for remote programming by external switch, process

controller, etc.

• LED status indications for power "On", output state, received signal

strength, and sensing contrast

• Choose models with integral 2 m (6.5 ft) cable or pico-style quick

disconnect (QD) connector; 9 m (30 ft) cables are also available

PIT46U fibers, opposed mode: 180 mm (7.1 in)*

PIT26U fibers, opposed mode: 50 mm (2.0 in)

PBT46U fiber, diffuse mode: 50 mm (2.0 in)

PBT26U fiber, diffuse mode: 10 mm (0.4 in)

* Opposed mode range may be extended using optional

lenses (see Banner Products Catalog for available lenses).

Summary of content (8 pages)

PAGE 1
D11 Expert Series – 5V dc Models Low cost teach-mode sensors for use with plastic fiber optics • Low cost, 5V dc self-contained TEACH mode sensors for use with all Banner plastic fiber optics • Compact 11 mm-wide housing designed for DIN rail mounting; can also be mounted to any surface using the supplied mounting bracket • Easy push button TEACH mode programming automatically adjusts sensitivity to optimal setting • Designed for high-performance, even in low-contrast sensing applications • Fast, 200 micro
PAGE 2
D11E Series RUN Mode Normal operation of the D11 Expert is called the "RUN mode".
PAGE 3
D11E Series Contrast Indication When the push button is clicked to teach the second sensing condition, the three LED indicators flash simultaneously to indicate relative sensing contrast. Contrast is the difference in light level between the two sensing conditions. Higher contrast allows higher sensitivity level, and resulting higher excess gain. A high contrast level is directly related to sensing reliability, and forgivingness to subtle changes in sensing conditions.
PAGE 4
D11E Series Output Pulse Stretcher A 40 millisecond pulse stretcher (OFF-delay) may be enabled for applications where a very short sensing event might be missed due to the response of the load or input connected to the sensor output.
PAGE 5
D11E Series DC Product Specifications Required Fiber Optic Cable PI or PB Series plastic fibers Sensing Beam Visible red, 680 nm Supply Voltage and Current 5V dc (±10%) at less than 45 mA, exclusive of load Output Configuration One (SPST) NPN (sinking) or PNP (sourcing) open-collector transistor, depending on model; Programmable for light or dark operate Output Rating 150 mA maximum; Off-state leakage current: <5 microamps at 30V dc; On-state saturation voltage: <0.8V at 80 mA dc; <1.
PAGE 6
D11E Series Hookup Diagrams Sensors with NPN (Sinking) Outputs Sensors with PNP (Sourcing) Outputs Cabled Hookup bn bu bk wh Cabled Hookup bn bu bk wh + 5V dc - Load Remote programming switch (normally open) - Load Remote programming switch (normally open) Quick disconnect Hookup bn bu bk wh + 5V dc Quick disconnect Hookup bn bu bk wh + 5V dc - Load Remote programming switch (normally open) + 5V dc - Load Remote programming switch (normally open) Quick Disconnect (QD) Cables The follo
PAGE 7
D11E Series Dimensions Cabled models Plastic Fiber Installation: Slide Up to Release Fibers 35.0 mm (1.38 in) Programming Push Button Power Indicator Output Indicator Signal Strength Indicator Cut fiber ends per instructions included with the fibers. Slide the fiber gripper up (open). For 0.25 mm or 0.5 mm diameter fibers, insert the adapter (shown below) into the ports as far as it will go. 2. All fibers: Insert the prepared plastic fiber sensor ends gently into the ports as far as they will go. 3.
PAGE 8
D11E Series Remote Programming The white wire of the D11E may be connected to a remote switch for the following sensor programming functions: 1) Disable or enable the push button 2) TEACH mode programming of sensitivity 3) Enable or disable the 40-millisecond pulse stretcher. A remote programming switch is connected between the white wire and dc common (see hookup diagrams on page 6).