Instruction Manual

ManualsBrandsBANNER ManualsConverterBANNER R45C Analog to IO-Link Device Converter

Table Of Contents

Instruction Manual

• Compact IO-Link device to analog converter that outputs an analog value, voltage or

current, as presented by the IO-Link master

• The converter also connects to an analog source, voltage or current, and outputs the

value to the IO-Link master and as a representative PFM output

• 4-pin M12 male quick-disconnect connector supports IO-Link

• Two 4-pin M12 female quick-disconnect connectors that each support analog inputs

and outputs

• Rugged over-molded design meets IP65, IP67, and IP68

• Connects directly to a sensor or anywhere in-line for ease of use

Models

Housing

R45

C = Converter

Q = Integral M12 quick disconnect

Connector

Female 1

II = Analog 1 Current In/Current Out

UU = Analog 1 Voltage In/Voltage Out

Male

C II

Female 2

II = Analog 2 Current In/Current Out

UU = Analog 2 Voltage In/Voltage Out

IIK

Function

- -

K = IO-Link

Note: Available models are analog current in/out, and analog voltage in/out.

Overview

Analog In

When an analog input value is received by this converter, the numerical representational value is sent to an IO-Link Master via Process Data In (PDI).

PDI Analog Ranges:

• Voltage = 0 mV to 10,000 mV

• Current = 4,000 µA to 20,000 µA

Analog Out

This converter also allows for the user to output an analog value by sending the numerical analog value from the IO-Link Master via Process Data

Out (PDO).

PDO Analog Ranges:

• Voltage = 0 mV to 11,000 mV

• Current = 0 µA to 24,000 µA

PDO Outside Valid Range (POVR)

If the PDO value sent to this converter is outside of the PDO Analog Range value, then the actual analog output value will be set to the one of the

three selectable POVR levels after a 2 second delay:

• Low (default): 0 V or 3.5 mA

• High: 10.5 V or 20.5 mA

• Hold: Level retains previous value indeﬁnitely

Note: If a connected IO-Link sensor is changed back to SIO mode, then the previous value will be held.

PFM Out

Enables a PFM representation of an analog input as an output.

PFM Input Source Channel

Selects the analog input value from Port 1 or Port 2 as the PFM output source.

Pulse Frequency Conﬁguration

Sets the near and far frequency values.

R45C IO-Link to Dual Analog Input-Output

Converter

Original Document

228480 Rev. A

14 December 2022

228480

Summary of content (5 pages)

PAGE 1
R45C IO-Link to Dual Analog Input-Output Converter Instruction Manual • • • • • • Compact IO-Link device to analog converter that outputs an analog value, voltage or current, as presented by the IO-Link master The converter also connects to an analog source, voltage or current, and outputs the value to the IO-Link master and as a representative PFM output 4-pin M12 male quick-disconnect connector supports IO-Link Two 4-pin M12 female quick-disconnect connectors that each support analog inputs and outputs R
PAGE 2
R45C IO-Link to Dual Analog Input-Output Converter Status Indicators The R45C IO-Link to Dual Analog Input-Output Converter has four amber LED indicators on both sides for IO-Link and analog communications to allow for installation needs and still provide adequate indication visibility. There is also a green LED indicator on both sides of the converter, which signals the device's power status. Figure 1.
PAGE 3
R45C IO-Link to Dual Analog Input-Output Converter CAUTION: Do not overtighten the R45C's mounting screw during installation. Overtightening can affect the performance of the R45C.
PAGE 4
R45C IO-Link to Dual Analog Input-Output Converter Accuracy 0.5% Indicators Green: Power Amber: IO-Link communications Amber: Analog input value present Amber: Analog output value in range Vibration and Mechanical Shock Meets IEC 60068-2-6 requirements (Vibration: 10 Hz to 55 Hz, 0.
PAGE 5
R45C IO-Link to Dual Analog Input-Output Converter Banner Engineering Corp Limited Warranty Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period.