User Manual

ManualsBrandsBanner ManualsEquipmentSureCross DX80 Wireless Networks

Configurable Node with discrete inputs and discrete outputs

For additional information, updated

documentation, and accessories, re-

fer to Banner Engineering's website,

www.bannerengineering.com/sure-

cross.

The SureCross® wireless system is a radio frequency network with integrated I/O that can oper-

ate in most environments and eliminate the need for wiring runs. Wireless networks are formed

around a Gateway, which acts as the wireless network master device, and one or more Nodes.

• Wireless industrial I/O device with four selectable discrete inputs and four sourcing discrete

outputs

• 10 to 30V dc power input

• DIP switches for user configuration

• Frequency Hopping Spread Spectrum (FHSS) technology and Time Division Multiple Access

(TDMA) control architecture ensure reliable data delivery within the unlicensed Industrial, Sci-

entific, and Medical (ISM) band

• Transceivers provide bidirectional communication between the Gateway and Node, including

fully acknowledged data transmission

• Lost RF links are detected and relevant outputs set to user-defined conditions

Models Frequency Antenna I/O

DX80N9X6S4P4

900 MHz ISM Band

External

Inputs: Four selectable discrete

Outputs: Four sourcing discrete

DX80N9X6W4P4 Internal

WARNING: Not To Be Used for Personnel Protection

Never use this device as a sensing device for personnel protection. Doing so could lead to serious

injury or death. This device does not include the self-checking redundant circuitry necessary to allow its

use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de-

energized sensor output condition.

SureCross User Configuration Tool

The User Configuration Tool (UCT) offers an easy way to link I/O points in your wire-

less network, view I/O register values graphically, and set system communication pa-

rameters when a host system is not part of the wireless network.

The UCT requires a special USB to RS-485 (model number BWA-UCT-900 for 1 Watt

radios, BWA-HW-006 can be used for all other radios) converter cable to pass infor-

mation between your computer and the Gateway. Download the most recent revi-

sions of the UCT software from Banner Engineering's website: http://www.banneren-

gineering.com/wireless.

Setting Up Your Wireless Network

To set up and install your wireless network, follow these steps:

1. Configure the DIP switches of all devices.

2. Connect the sensors to the SureCross devices.

3. Apply power to all devices.

4. Form the wireless network by binding the Nodes to the Gateway. If the binding instructions are not included in the datasheet, refer to

the product manual for binding instructions.

5. Observe the LED behavior to verify the devices are communicating with each other.

6. Conduct a site survey between the Gateway and Nodes. If the site survey instructions are not included in this datasheet, refer to the

product manual for detailed site survey instructions.

SureCross DX80 Node

P/N 131293 Rev. F 5/21/2013

0 131293 0

Summary of content (7 pages)

PAGE 1
SureCross DX80 Node Configurable Node with discrete inputs and discrete outputs The SureCross® wireless system is a radio frequency network with integrated I/O that can operate in most environments and eliminate the need for wiring runs. Wireless networks are formed around a Gateway, which acts as the wireless network master device, and one or more Nodes.
PAGE 2
SureCross DX80 Node 7. Install your wireless sensor network components. If installation instructions are not included in this datasheet, refer to the product manual for detailed installation instructions. For additional information, including installation and setup, weatherproofing, device menu maps, troubleshooting, and a list of accessories, refer to one of the following product manuals.
PAGE 3
SureCross DX80 Node Address Mode The SureCross wireless devices may use one of two types of addressing modes: rotary dial addressing or extended addressing. In rotary dial address mode, the left rotary dial establishes the network ID and the right rotary dial sets the device ID. The wireless network is restricted to a maximum of 16 devices. Extended address mode uses a security code to "bind" Nodes to a specific Gateway.
PAGE 4
SureCross DX80 Node Wiring Diagrams for Discrete Inputs Connecting dc power to the communication pins will cause permanent damage. For the DX8x...C models, PWR in the wiring diagram refers to V+ on the wiring board and GND in the wiring diagram refers to V- on the wiring board. Discrete Input Wiring for PNP Sensors Discrete Input Wiring for NPN Sensors PWR 10-30V dc DIx DIx GND dc common Wiring Diagrams for Discrete Outputs Connecting dc power to the communication pins will cause permanent damage.
PAGE 5
SureCross DX80 Node I/O # Modbus Holding Register I/O Type I/O Range Holding Register Representation Min. Value Max. Value Min. (Dec.) Max. (Dec.) Terminal Block Labels Gateway Any Node 9 9 9 + (Node# × 16) Discrete OUT 1 0 1 0 1 DO1 10 10 10 + (Node# × 16) Discrete OUT 2 0 1 0 1 DO2 11 11 11 + (Node# × 16) Discrete OUT 3 0 1 0 1 DO3 12 12 12 + (Node# × 16) Discrete OUT 4 0 1 0 1 DO4 ...
PAGE 6
SureCross DX80 Node Inputs and Outputs Discrete Input OFF Condition PNP: Less than 5V NPN: Greater than 2V or open Discrete Output Rating (PNP) 100 mA max current at 30V dc ON-State Saturation: Less than 3V at 100 mA OFF-state Leakage: Less than 10 μA Output State Following Timeout De-energized (OFF) Environmental and Certifications Rating IEC IP67; NEMA 6; (See UL section below for any applicable UL specifications) Operating Conditions Temperature: −40 to +85 °C (Electronics); −20 to +80 °C (LCD) Humidi
PAGE 7
SureCross DX80 Node Banner Engineering Corp Limited Warranty Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period.