Instruction Manual

ManualsBrandsBanner ManualsEquipmentSureCross DX80 Wireless Networks

Printed in USA 08/09 P/N 129318 rev. D

SureCross™ DX80K Wireless Conﬁgured

FlexPower™ Kit

Discrete inputs from a Gateway to 1 Node with switched power output

WARNING . . .

Not To Be Used for Personnel Protection

Never use these products for personnel protection. Doing so could lead to serious injury or death.

These products do NOT include the self-checking redundant circuitry necessary to allow their use in personnel safety applications. A

failure or malfunction can cause either an energized or de-energized output condition. Consult your current Banner Safety Products

catalog for safety products that meet OSHA, ANSI, and IEC standards for personnel protection.

Model Frequency Power I/O Mapping I/O Devices

DX80K9M3PE1 900 MHz ISM Band

+10 to 30V dc (Gateway)

3.6V dc Battery (Node)

Conﬁgured

(See hookup

diagram)

Discrete In (Sinking)

Discrete Out (Sourcing)

1 Gateway, 1 Node, 1

DX81 Battery Module

DX80K2M3PE1 2.4 GHz ISM Band

Models

Features

The SureCross™ DX80 is a radio frequency network system built around a Gateway and one

or more Nodes. Conﬁgured kits are packaged in a box with the preset Gateway, Node(s),

accessories, and hardware to get up and running quickly.

Kit contains 10 to 30V dc powered Gateway, • FlexPower™ Node, and DX81 FlexPower

supply module for powering Node and switched power output of discrete sensor

Gateway input-to-output mapping connects the Node’s discrete (sinking) inputs with the •

Gateway’s two discrete (sourcing) outputs

Proprietary radio optimized for effective power management•

Frequency Hopping Spread Spectrum (FHSS) technology and Time Division Multiple •

Access (TDMA) control architecture combine to ensure reliable data delivery within the

unlicensed Industrial, Scientiﬁc, and Medical (ISM) bands

Transceivers provide two-way communication between the Gateway and Node, including •

fully acknowledged data transmission

Site Survey analyzes the network’s signal strength and reliability•

Lost RF links are detected and relevant outputs set to predeﬁned conditions•

For additional information and a complete list of accessories, including FCC approved

antennas, please refer to Banner Engineering’s website, www.bannerengineering.com/

surecross.

Summary of content (8 pages)

PAGE 1
SureCross™ DX80K Wireless Configured FlexPower™ Kit Discrete inputs from a Gateway to 1 Node with switched power output Features The SureCross™ DX80 is a radio frequency network system built around a Gateway and one or more Nodes. Configured kits are packaged in a box with the preset Gateway, Node(s), accessories, and hardware to get up and running quickly.
PAGE 2
SureCross™ DX80K Wireless Configured FlexPower™ Kit PWR PWR Hookup Diagrams DI1 DI2 GND GND DO1 DO2 DO4 DO3 GND GND DI3 SP3 SP4 PWRPWR GND GND GND GND A1+ A2+ DI4 DO2 DO1 DI2 A1− A2− MINI-BEAM® Power DI1 SP1 SP2 Configured input/output mapping I/O Point Terminal Block Label DX80 Gateway DX80 Node Terminal Block Label I/O Point 9 DO1 Discrete OUT 1 Discrete IN 1 DI1 1 10 DO2 Discrete OUT 2 Discrete IN 2 DI2 2 MINI-BEAM®* These are the I/O points as displayed on the dev
PAGE 3
SureCross™ DX80K Wireless Configured FlexPower™ Kit FlexPower Device Configuration Cycle Power After making any changes to the DIP switch positions, cycle power to the device to activate the changes. For devices with batteries integrated into the housing, remove the battery for one minute to cycle power to the device. Do not change the position of any DIP switch other than DIP switches 1 and 2. This kit is configured at the factory.
PAGE 4
SureCross™ DX80K Wireless Configured FlexPower™ Kit Discrete Configuration The discrete configuration matches the switch power outputs (SP1, SP2) with the discrete inputs. The analog inputs are disabled. The discrete configuration is selected when switch 2 is in the ON position. Two sinking discrete outputs are active for this configuration.
PAGE 5
SureCross™ DX80K Wireless Configured FlexPower™ Kit Rotary Dial Positions Rotary Dial Addressing Mode When using Rotary Dial Addressing Mode, the Gateway’s and Node’s rotary dials are in the correct position. The left rotary dial establishes the Network ID and the right dials establish the Device ID. When using multiple networks within range of each other, set each network to a different Network ID using the left rotary dial.
PAGE 6
SureCross™ DX80K Wireless Configured FlexPower™ Kit Specifications Many parameters are configurable. The values in the tables represent factory defaults unless otherwise noted. Radio Range* 900 MHz: Up to 4.8 kilometers (3 miles) 2.4 GHz: Up to 3.2 kilometers (2 miles) Transmit Power 900 MHz: 21 dBm Conducted 2.4 GHz: 18 dBm Conducted, ≤ 20 dBm EIRP Spread Spectrum Technology FHSS (Frequency Hopping Spread Spectrum) Antenna Connector Ext. Reverse Polarity SMA, 50 Ohms Antenna Max.
PAGE 7
SureCross™ DX80K Wireless Configured FlexPower™ Kit Outputs * Discrete Outputs (Gateway) Two Sourcing Discrete Output Rating 100 mA max current at 30V dc ON-State Saturation: Less than 3V at 100 mA OFF-state Leakage: Less than 10 µA Discrete Output ON Condition Supply minus 2V Discrete Output OFF Condition Less than 2V Maximum End-to-end Latency* 200 milliseconds Output State Following Timeout De-energized (OFF) From the sample point and with a good RF signal.
PAGE 8
SureCross™ DX80K Wireless Configured FlexPower™ Kit For more information: Contact your local Banner representative or Banner Corporate Offices around the world. Corporate Headquarters Banner Engineering Corp. 9714 Tenth Ave. North Mpls., MN 55441 Tel: 763-544-3164 www.bannerengineering.com sensors@bannerengineering.com Asia ─ China Banner Engineering China Shanghai Rep Office Rm. G/H/I, 28th Flr. Cross Region Plaza No. 899, Lingling Road Shanghai 200030 CHINA Tel: 86-21-54894500 Fax: 86-21-54894511 www.