Owner's manual

ManualsBrandsBanner ManualsEquipmentSureCross DX80 Wireless Networks

Configurable FlexPower Node with a 1-wire serial interface

IP67 Base

2.4 GHz

IP20 Base

900 MHz

For additional information, up-

dated documentation, and ac-

cessories, refer to Banner Engi-

neering's website, www.banner-

engineering.com/surecross.

The SureCross® wireless system is a radio frequency network with integrated I/O that can operate in

most environments and eliminate the need for wiring runs. Wireless networks are formed around a

Gateway, which acts as the wireless network master device, and one or more Nodes.

• Wireless industrial I/O device with a 1-wire serial interface to handle up to two 1-wire serial sens-

ing devices

• FlexPower® power options allows for +10 to 30V dc, solar, and battery power sources for low

power applications.

• DIP switches for user configuration

• Two switch power outputs provide sensor actuation voltage of 3.6V dc (battery powered) or 4.3V

dc (10 to 30V dc powered)

• Frequency Hopping Spread Spectrum (FHSS) technology and Time Division Multiple Access

(TDMA) control architecture ensure reliable data delivery within the unlicensed Industrial, Scientif-

ic, and Medical (ISM) band

• Transceivers provide bidirectional communication between the Gateway and Node, including fully

acknowledged data transmission

• Lost RF links are detected and relevant outputs set to user-defined conditions

• The DX80...C models are certified for use in Class I, Division 2, Group A, B, C, D; Zone 2 (Cate-

gory 3G) Hazardous Locations when properly installed in accordance with the National Electrical

Code, the Canadian Electrical Code, or applicable local codes/regulations (see Specifications)

Models

Frequency Environmental Rating I/O

DX80N9X2S2S 900 MHz ISM Band

IP67, NEMA 6

Inputs: 1-Wire serial interface for up to

two 1-wire serial sensing devices

dc Power Outputs: Two

DX80N2X2S2S 2.4 GHz ISM Band

DX80N9X2S2SC 900 MHz ISM Band IP20, NEMA 1

Class I, Division 2, Group A, B, C, D Hazardous

Locations (see Specifications)

DX80N2X2S2SC 2.4 GHz ISM Band

Internal antenna models are also available. For more information, contact your local Banner Engineering Corp. representative.

WARNING: Not To Be Used for Personnel Protection

Never use this device as a sensing device for personnel protection. Doing so could lead to serious

injury or death. This device does not include the self-checking redundant circuitry necessary to allow its

use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de-

energized sensor output condition.

SureCross User Configuration Tool

The User Configuration Tool (UCT) offers an easy way to link I/O points in your wire-

less network, view I/O register values graphically, and set system communication pa-

rameters when a host system is not part of the wireless network.

The UCT requires a special USB to RS-485 (model number BWA-UCT-900 for 1 Watt

radios, BWA-HW-006 can be used for all other radios) converter cable to pass infor-

mation between your computer and the Gateway. Download the most recent revi-

sions of the UCT software from Banner Engineering's website: http://www.banneren-

gineering.com/wireless.

Setting Up Your Wireless Network

To set up and install your wireless network, follow these steps:

1. Configure the DIP switches of all devices.

SureCross DX80 FlexPower Serial Interface Node

P/N 136971 Rev. G 6/20/2013

0 136971 1

Summary of content (8 pages)

PAGE 1
SureCross DX80 FlexPower Serial Interface Node Configurable FlexPower Node with a 1-wire serial interface The SureCross® wireless system is a radio frequency network with integrated I/O that can operate in most environments and eliminate the need for wiring runs. Wireless networks are formed around a Gateway, which acts as the wireless network master device, and one or more Nodes.
PAGE 2
SureCross DX80 FlexPower Serial Interface Node 2. Connect the sensors to the SureCross devices. 3. Apply power to all devices. 4. Form the wireless network by binding the Nodes to the Gateway. If the binding instructions are not included in the datasheet, refer to the product manual for binding instructions. 5. Observe the LED behavior to verify the devices are communicating with each other. 6. Conduct a site survey between the Gateway and Nodes.
PAGE 3
SureCross DX80 FlexPower Serial Interface Node Switches Device Settings 1 2 3 4 5 6 7 8 Sensor 1: 6 inputs, 6 outputs (Primary and secondary I/O 1-3) OFF ON ON Sensor 1 & 2: 3 inputs, 0 outputs (Primary inputs 1-3) ON OFF OFF Sensors 1 & 2: 1 input, 0 outputs (Primary input 1), and Discrete IN 1 through 4** ON OFF ON Sensors 1 & 2: 2 inputs, 0 outputs (Primary inputs 1-2), Discrete IN 1, and Discrete IN 2** ON ON OFF Sensors 1 & 2: 3 inputs, 3 outputs (Primary I/O 1-3) ON ON ON
PAGE 4
SureCross DX80 FlexPower Serial Interface Node Sample and Report Rates The sample interval, or rate, defines how often the SureCross device samples the input. For battery-powered applications, setting a slower rate extends the battery life. The report rate defines how often the Node communicates the I/O status to the Gateway. Change of state reporting sets the system to report only when the value crosses the threshold setting.
PAGE 5
SureCross DX80 FlexPower Serial Interface Node Terminal Block (IP20 Housing) For the DX8x...C models, PWR in the wiring diagram refers to V+ on the wiring board and GND in the wiring diagram refers to V- on the wiring board. Ignore alternate labeling referring to other models that use this board. FlexPower Discrete Models FlexPower Serial Interface Models FlexPower Counter Models B+. 3.6 to 5.5V dc (for battery powered models only). B+. 3.6 to 5.5V dc (for battery powered models only). CMx.
PAGE 6
SureCross DX80 FlexPower Serial Interface Node I/O Point Modbus Holding Register I/O Type Gateway Any Node 2 2 2 + (Node# × 16) Serial device 1, primary input 2; OR Discrete IN 3 0h01 3 3 3 + (Node# × 16) Serial device 1, primary input 3; OR Discrete IN 1 0h02 4 4 4 + (Node# × 16) Serial device 1, secondary input 1; OR Serial device 2, primary input 1 0h03* 0h00 5 5 5 + (Node# × 16) Serial device 1, secondary input 2; OR Serial device 2, primary input 2; OR Discrete IN 4 0h04* 0h01
PAGE 7
SureCross DX80 FlexPower Serial Interface Node Radio and General Spread Spectrum Technology Interface FHSS (Frequency Hopping Spread Spectrum) Indicators: Two bi-color LEDs Link Timeout Buttons: Two Gateway: Configurable via User Configuration Tool Display: Six character LCD (UCT) software Wiring Access Node: Defined by Gateway Four PG-7, One 1/2-inch NPT, One 5-pin Euro-style Radio range is with the 2 dB antenna that ships with the product.
PAGE 8
SureCross DX80 FlexPower Serial Interface Node • BWA-HW-011: IP20 Screw Terminal Headers (2 pack) (Included only with the IP20 DX80...C models) Sensors with a Serial Interface The following sensors are designed to be used with the FlexPower Node with Serial Interface. Sensors Part No. Model No. Description 79610 M12FTH1Q Temperature and Humidity Sensor, ±2% Accuracy 1-wire serial interface 81050 M12FTH2Q Temperature and Humidity Sensor, ±3.