Manual

ManualsBrandsBanner ManualsEquipmentSureCross DX80 Wireless Networks

Printed in USA 08/09 P/N 136441 rev. B

SureCross™ DX80K Wireless Conﬁgured Kit

Analog (0–10V) I/O between Gateway and 1 Node

WARNING . . .

Not To Be Used for Personnel Protection

Never use these products for personnel protection. Doing so could lead to serious injury or death.

These products do NOT include the self-checking redundant circuitry necessary to allow their use in personnel safety applications. A

failure or malfunction can cause either an energized or de-energized output condition. Consult your current Banner Safety Products

catalog for safety products that meet OSHA, ANSI, and IEC standards for personnel protection.

Features

The SureCross™ DX80 is a radio frequency network system built around a Gateway and one

or more Nodes. Conﬁgured kits are packaged in a box with the preset Gateway, Node(s),

accessories, and hardware to get up and running quickly.

Gateway input-to-output mapping provides four analog (0–10V dc) inputs and four analog •

(0–10V dc) outputs on the Gateway mapped to four analog (0–10V dc) inputs and four

analog (0–10V dc) outputs on the Node

+10 to 30V dc power•

Proprietary radio optimized for effective power management•

Frequency Hopping Spread Spectrum (FHSS) technology and Time Division Multiple •

Access (TDMA) control architecture combine to ensure reliable data delivery within the

unlicensed Industrial, Scientiﬁc, and Medical (ISM) bands

Transceivers provide two-way communication between the Gateway and Node, including •

fully acknowledged data transmission

Site Survey analyzes the network’s signal strength and reliability•

Lost RF links are detected and relevant outputs set to predeﬁned conditions•

For additional information and a complete list of accessories, including FCC approved

antennas, refer to Banner Engineering’s website, www.bannerengineering.com/surecross.

Model Power Frequency I/O

DX80K9M6AV1

+10 to 30V dc

900 MHz ISM Band

Analog Inputs: Four 0–10V dc

Analog Outputs: Four 0–10V dc

DX80K2M6AV1

2.4 GHz ISM Band

Models

Summary of content (8 pages)

PAGE 1
SureCross™ DX80K Wireless Configured Kit Analog (0–10V) I/O between Gateway and 1 Node Features The SureCross™ DX80 is a radio frequency network system built around a Gateway and one or more Nodes. Configured kits are packaged in a box with the preset Gateway, Node(s), accessories, and hardware to get up and running quickly.
PAGE 2
SureCross™ DX80K Wireless Configured Kit Hookup Diagrams I/O Point Terminal Block Label DX80 Gateway DX80 Node Terminal Block Label 1 AI1 Analog IN 1 Analog OUT 1 AO1 9 2 AI2 Analog IN 2 Analog OUT 2 AO2 10 3 AI3 Analog IN 3 Analog OUT 3 AO3 11 4 AI4 Analog IN 4 Analog OUT 4 AO4 12 9 AO1 Analog OUT 1 Analog IN 1 AI1 1 AO2 Analog OUT 2 Analog IN 2 AI2 2 11 AO3 Analog OUT 3 Analog IN 3 AI3 3 12 AO4 Analog OUT 4 Analog IN 4 AI4 4 5-pin Euro-style Hookup (RS-4
PAGE 3
SureCross™ DX80K Wireless Configured Kit Device Configuration Cycle Power After making any changes to the DIP switch positions, cycle power to the device to activate the changes. For devices with batteries integrated into the housing, remove the battery for one minute to cycle power to the device. Device Settings Rotary Switch Address Mode Extended Address Mode 1 Switches 2 3 4 OFF* Do not change the position of any DIP switch other than DIP switch 1. This kit is configured at the factory.
PAGE 4
SureCross™ DX80K Wireless Configured Kit Rotary Dial Positions Rotary Dial Addressing Mode When using Rotary Dial Addressing Mode, the Gateway’s and Node’s rotary dials are in the correct position. The left rotary dial establishes the Network ID and the right dials establish the Device ID. When using multiple networks within range of each other, set each network to a different Network ID using the left rotary dial.
PAGE 5
SureCross™ DX80K Wireless Configured Kit Specifications Many parameters are configurable. The values in the tables represent factory defaults unless otherwise noted. Radio Range* 900 MHz: Up to 4.8 kilometers (3 miles) 2.4 GHz: Up to 3.2 kilometers (2 miles) Transmit Power 900 MHz: 21 dBm Conducted 2.4 GHz: 18 dBm Conducted, ≤ 20 dBm EIRP Spread Spectrum Technology FHSS (Frequency Hopping Spread Spectrum) Antenna Connector Ext. Reverse Polarity SMA, 50 Ohms Antenna Max. Tightening Torque 0.
PAGE 6
SureCross™ DX80K Wireless Configured Kit Environmental * ** Environmental Rating* IEC IP67; NEMA 6 Operating Temperature** −40 to +85° C (Electronics); −20 to +80° C (LCD) Operating Humidity 95% max. relative (non-condensing) Radiated Immunity 10 V/m, 80-2700 MHz (EN61000-6-2) Shock and Vibration IEC 68-2-6 and IEC 68-2-7 Shock: 30g, 11 millisecond half sine wave, 18 shocks Vibration: 0.
PAGE 7
SureCross™ DX80K Wireless Configured Kit Notes Banner Engineering Corp. • Minneapolis, MN U.S.A www.bannerengineering.com • Tel: 763.544.3164 P/N 136441 rev.
PAGE 8
SureCross™ DX80K Wireless Configured Kit For more information: Contact your local Banner representative or Banner Corporate Offices around the world. Corporate Headquarters Banner Engineering Corp. 9714 Tenth Ave. North Mpls., MN 55441 Tel: 763-544-3164 www.bannerengineering.com sensors@bannerengineering.com Asia ─ China Banner Engineering China Shanghai Rep Office Rm. G/H/I, 28th Flr. Cross Region Plaza No. 899, Lingling Road Shanghai 200030 CHINA Tel: 86-21-54894500 Fax: 86-21-54894511 www.