Manual

ManualsBrandsBanner ManualsEquipmentSureCross DX80 Wireless Networks

GatewayPro models for protocol conversion or web-based configuration

2.4 GHz

900 MHz

The SureCross® wireless system is a radio frequency network with integrated I/O that can

operate in most environments and eliminate the need for wiring runs. Wireless networks are

formed around a Gateway, which acts as the wireless network master device, and one or

more Nodes.

• 10 to 30V dc power input

• Modbus serial interface and Ethernet interface

• Site Survey analyzes the network’s signal strength and reliability and displays the results

on the Gateway's LCD

• Frequency Hopping Spread Spectrum (FHSS) technology and Time Division Multiple Ac-

cess (TDMA) control architecture ensure reliable data delivery within the unlicensed Indus-

trial, Scientific, and Medical (ISM) band

• Transceivers provide bidirectional communication between the Gateway and Node, includ-

ing fully acknowledged data transmission

For additional information, updated documentation, and accessories, refer to Banner Engi-

neering's website, www.bannerengineering.com/surecross.

Models Feature Frequency Antenna

DX80P9T6S

Modbus/TCP or EtherNet/IP communication

protocol

900 MHz ISM Band

External

DX80P9T6W Internal

DX80P2T6S

2.4 GHz ISM Band

External

DX80P2T6W Internal

DX80P9A6S

Modbus/TCP protocol, Configuration capabil-

ity using the Web Configurator

900 MHz ISM Band

External

DX80P9A6W Internal

DX80P2A6S

2.4 GHz ISM Band

External

DX80P2A6W Internal

WARNING: Not To Be Used for Personnel Protection

Never use this device as a sensing device for personnel protection. Doing so could lead to serious

injury or death. This device does not include the self-checking redundant circuitry necessary to allow its

use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de-

energized sensor output condition.

The SureCross® DX80 Wireless Network

Gateway

Node

FlexPower Node

and Battery Supply Module

The SureCross® DX80 wireless I/O network provides reliable moni-

toring without wiring or conduit installation. The SureCross wireless

network operates independently or in conjunction with a host system,

PLC, and/or PC software.

Each wireless network system consists of one Gateway and one or

more Nodes. Devices ship with factory-defined discrete, analog, or a

mix of discrete and analog inputs and outputs.

The SureCross® DX80 network is a deterministic system—the net-

work identifies when the radio signal is lost and drives relevant out-

SureCross DX80 GatewayPro

P/N 131933 Rev. F 5/23/2013

0 131933 1

Summary of content (7 pages)

PAGE 1
SureCross DX80 GatewayPro GatewayPro models for protocol conversion or web-based configuration The SureCross® wireless system is a radio frequency network with integrated I/O that can operate in most environments and eliminate the need for wiring runs. Wireless networks are formed around a Gateway, which acts as the wireless network master device, and one or more Nodes.
PAGE 2
SureCross DX80 GatewayPro puts to user-defined conditions. After the radio signal is reacquired, the network returns to normal operation. SureCross® DX80 Gateways and Nodes A Gateway is the master device within each radio network. Every wireless network must have one Gateway, which schedules communication traffic and controls the I/O configuration for the network, and one or more Nodes.
PAGE 3
SureCross DX80 GatewayPro Setting Up Your Wireless Network To set up and install your wireless network, follow these steps: 1. 2. 3. 4. Configure the DIP switches of all devices. Connect the sensors to the SureCross devices. Apply power to all devices. Form the wireless network by binding the Nodes to the Gateway. If the binding instructions are not included in the datasheet, refer to the product manual for binding instructions. 5.
PAGE 4
SureCross DX80 GatewayPro DIP Switch Settings Switches Device Settings 1 2 Rotary dial address mode OFF* Extended address mode ON 3 4 * Default configuration Address Mode The SureCross wireless devices may use one of two types of addressing modes: rotary dial addressing or extended addressing. In rotary dial address mode, the left rotary dial establishes the network ID and the right rotary dial sets the device ID. The wireless network is restricted to a maximum of 16 devices.
PAGE 5
SureCross DX80 GatewayPro LED 1 LED 2 (flashing red) Gateway Status Device Error (flashing red) Modbus Communication Active (flashing yellow) Modbus Communication Error (flashing red) For Gateway and Ethernet Bridge systems, active Modbus communication refers to the communication between the Gateway and the Ethernet Bridge. For GatewayPro systems, the Modbus communication LEDs refer to the communication internal to the GatewayPro.
PAGE 6
SureCross DX80 GatewayPro Radio and General 900 MHz Compliance (150 mW Radios) Housing FCC ID TGUDX80 - This device complies with FCC Polycarbonate housing and rotary dial cover; polyester Part 15, Subpart C, 15.247 labels; EDPM rubber cover gasket; nitrile rubber, nonsulphur cured button covers IC: 7044A-DX8009 Weight: 0.26 kg (0.57 lbs) 2.4 GHz Compliance Mounting: #10 or M5 (SS M5 hardware included) FCC ID UE300DX80-2400 - This device complies with FCC Part 15, Subpart C, 15.247 Max.
PAGE 7
SureCross DX80 GatewayPro Ethernet Cables Part No. Model No. Description 77669 BWA-E2M Ethernet cable, RSCD RJ45 440, 2M 78469 BWA-E8M Ethernet cable, RSCD RJ45 440, 8M 78467 BWA-EX2M Ethernet cable, crossover, RSCD RJ45CR 440, 2M Use a crossover cable to connect the DX80 GatewayPro or DX83 Ethernet Bridge to a host system without using an Ethernet switchbox or hub. When using a switchbox or hub, use a straight cable. Warnings Antenna Installations.