Owner's manual

ManualsBrandsBanner ManualsEquipmentSureCross DX80 Wireless Networks

Configurable Node with an integrated battery, 1 selectable counter input, 1 selectable discrete input, and 1 discrete NMOS output

The SureCross® wireless system is a radio frequency network with integrated I/O that can operate in

most environments and eliminate the need for wiring runs. Wireless networks are formed around a

Gateway, which acts as the wireless network master device, and one or more Nodes.

• Wireless industrial I/O device with one selectable discrete input, one selectable counter input

(rate or event; sinking, sourcing, or self-energized), and one NMOS discrete output

• User selectable 10 kHz event counter or 25 kHz rate counter

• FlexPower® technology driven by one lithium primary battery integrated into the housing

• DIP switches for user configuration

• Frequency Hopping Spread Spectrum (FHSS) technology and Time Division Multiple Access

(TDMA) control architecture ensure reliable data delivery within the unlicensed Industrial, Scien-

tific, and Medical (ISM) band

• Transceivers provide bidirectional communication between the Gateway and Node, including

fully acknowledged data transmission

• Lost RF links are detected and relevant outputs set to user-defined conditions

For additional information, updated documentation, and accessories, refer to Banner Engineering's website, www.bannerengineer-

ing.com/surecross.

Models Frequency Environmental Rat-

ing

I/O

DX80N9X1S2A1 900 MHz ISM Band

IP67, NEMA 6

Inputs: One selectable discrete, one selectable counter

Outputs: One NMOS sinking discrete

DX80N2X1S2A1 2.4 GHz ISM Band

Internal antenna models are also available. For more information, contact your local Banner Engineering Corp. representative.

WARNING: Not To Be Used for Personnel Protection

Never use this device as a sensing device for personnel protection. Doing so could lead to serious

injury or death. This device does not include the self-checking redundant circuitry necessary to allow its

use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de-

energized sensor output condition.

SureCross User Configuration Tool

The User Configuration Tool (UCT) offers an easy way to link I/O points in your wire-

less network, view I/O register values graphically, and set system communication pa-

rameters when a host system is not part of the wireless network.

The UCT requires a special USB to RS-485 (model number BWA-UCT-900 for 1 Watt

radios, BWA-HW-006 can be used for all other radios) converter cable to pass infor-

mation between your computer and the Gateway. Download the most recent revi-

sions of the UCT software from Banner Engineering's website: http://www.banneren-

gineering.com/wireless.

Setting Up Your Wireless Network

To set up and install your wireless network, follow these steps:

1. Configure the DIP switches of all devices.

2. Connect the sensors to the SureCross devices.

3. Apply power to all devices.

SureCross DX80 FlexPower Counter Node

P/N 136972 Rev. F 5/22/2013

0 136972 0

Summary of content (9 pages)

PAGE 1
SureCross DX80 FlexPower Counter Node Configurable Node with an integrated battery, 1 selectable counter input, 1 selectable discrete input, and 1 discrete NMOS output The SureCross® wireless system is a radio frequency network with integrated I/O that can operate in most environments and eliminate the need for wiring runs. Wireless networks are formed around a Gateway, which acts as the wireless network master device, and one or more Nodes.
PAGE 2
SureCross DX80 FlexPower Counter Node 4. Form the wireless network by binding the Nodes to the Gateway. If the binding instructions are not included in the datasheet, refer to the product manual for binding instructions. 5. Observe the LED behavior to verify the devices are communicating with each other. 6. Conduct a site survey between the Gateway and Nodes. If the site survey instructions are not included in this datasheet, refer to the product manual for detailed site survey instructions. 7.
PAGE 3
SureCross DX80 FlexPower Counter Node Switches Device Settings 1 2 3 4 5 6 7 8 Report Rate 1 second ON * Default configuration Address Mode The SureCross wireless devices may use one of two types of addressing modes: rotary dial addressing or extended addressing. In rotary dial address mode, the left rotary dial establishes the network ID and the right rotary dial sets the device ID. The wireless network is restricted to a maximum of 16 devices.
PAGE 4
SureCross DX80 FlexPower Counter Node Debounce. Debounce establishes how to examine a signal’s transitions. The factory default setting is to activate the input filtering to compensate for unclean state transitions. To turn off the input filtering, set the switch to the ON position. Device switches Inputs. Counter switches 6 and 7 define the inputs as self-energized, sinking (NPN), or sourcing (PNP). A self-energized input does not require pull-up or pull-down devices for proper operation.
PAGE 5
SureCross DX80 FlexPower Counter Node Modbus Register Table I/O Point 1 Modbus Holding Register Gateway Nodes 1 1 + (Node# × 16) I/O Type Holding Register Representation I/O Range Min. Max. Min. (Dec.) Max. (Dec.) Discrete IN 1 0 1 0 1 ...
PAGE 6
SureCross DX80 FlexPower Counter Node Node Reg 15 0x8F 2 Node Reg 16 D3D9 Node Reg 7 0x8F 2 The counter has been preset to 20,567,001 (0x0139 D3D9) Preset Using the Node’s Menu System To manually enter a counter preset, follow the LCD menu flow using the diagram shown. 1. Single click button 1 to move across the top level menus. Click button 1 until the display shows IOCFG. 2. Click button 2 to enter the I/O Configuration submenu structure. 3. Single click button 1 to move across the I/O points.
PAGE 7
SureCross DX80 FlexPower Counter Node To replace the lithium "D" cell battery in any integrated housing model, follow these steps. 1. Remove the four screws mounting the face plate to the housing and remove the face plate. 2. Remove the discharged battery and replace with a new battery. Only use a 3.6V lithium battery from Xeno, model number XL-205F. 3. Verify the battery’s positive and negative terminals align to the positive and negative terminals of the battery holder mounted within the case.
PAGE 8
SureCross DX80 FlexPower Counter Node Inputs and Outputs Counter Inputs Threshold: 1.5V or 0.25V (Sinking or sourcing selected inputs require the 1.5V threshold setting) Debouce: DIP Switch Selectable. Enable debounce to filter a noisy input signal that may lead to false triggers.
PAGE 9
SureCross DX80 FlexPower Counter Node Violating Warnings. The manufacturer does not take responsibility for the violation of any warning listed in this document. Make no modifications to this product; any modifications to this product not expressly approved by Banner Engineering could void the user’s authority to operate the product. All specifications published in this document are subject to change; Banner reserves the right to modify product specifications or to update documentation at any time.