User guide

ManualsBrandsBanner ManualsEquipmentSureCross DX80 Wireless Networks

Configurable Node with 4 discrete inputs and 8 discrete outputs

IP67 Base

2.4 GHz

IP20 Base

900 MHz

The SureCross® wireless system is a radio frequency network with integrated I/O that can operate

in most environments and eliminate the need for wiring runs. Wireless networks are formed around

a Gateway, which acts as the wireless network master device, and one or more Nodes.

• Wireless industrial I/O device with four selectable discrete inputs and eight sourcing discrete

outputs

• 10 to 30V dc power input

• DIP switches for user configuration

• Frequency Hopping Spread Spectrum (FHSS) technology and Time Division Multiple Access

(TDMA) control architecture ensure reliable data delivery within the unlicensed Industrial, Sci-

entific, and Medical (ISM) band

• Transceivers provide bidirectional communication between the Gateway and Node, including

fully acknowledged data transmission

• Lost RF links are detected and relevant outputs set to user-defined conditions

• The DX80...C models are certified for use in Class I, Division 2, Group A, B, C, D; Zone 2 (Cat-

egory 3G) Hazardous Locations when properly installed in accordance with the National Electri-

cal Code, the Canadian Electrical Code, or applicable local codes/regulations (see Specifica-

tions)

For additional information, updated documentation, and accessories, refer to Banner Engineering's website, www.bannerengineer-

ing.com/surecross.

Models Frequency Environmental Rating I/O

DX80N9X6S4P8

900 MHz ISM

Band

IP67, NEMA 6

Inputs: Four selectable discrete

Outputs: Eight sourcing discrete

(When your wireless network does not include a host

system, the four input/eight output Node must be map-

ped to the eight input/four output Gateway.)

DX80N2X6S4P8 2.4 GHz ISM Band

DX80N9X6S4P8C

900 MHz ISM

Band

IP20, NEMA 1

Class I, Division 2, Group A, B,

C, D Hazardous Locations (see

Specifications)

DX80N2X6S4P8C 2.4 GHz ISM Band

Internal antenna models are also available, but are not UL Listed. For more information, contact your local Banner Engineering Corp.

representative.

WARNING: Not To Be Used for Personnel Protection

Never use this device as a sensing device for personnel protection. Doing so could lead to serious

injury or death. This device does not include the self-checking redundant circuitry necessary to allow its

use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de-

energized sensor output condition.

SureCross User Configuration Tool

The User Configuration Tool (UCT) offers an easy way to link I/O points in your wire-

less network, view I/O register values graphically, and set system communication pa-

rameters when a host system is not part of the wireless network.

The UCT requires a special USB to RS-485 (model number BWA-UCT-900 for 1 Watt

radios, BWA-HW-006 can be used for all other radios) converter cable to pass infor-

mation between your computer and the Gateway. Download the most recent revi-

sions of the UCT software from Banner Engineering's website: http://www.banneren-

gineering.com/wireless.

SureCross DX80 Node

P/N 132161 Rev. H 5/22/2013

0 132161 4

Summary of content (7 pages)

PAGE 1
SureCross DX80 Node Configurable Node with 4 discrete inputs and 8 discrete outputs IP67 Base 2.4 GHz IP20 Base 900 MHz The SureCross® wireless system is a radio frequency network with integrated I/O that can operate in most environments and eliminate the need for wiring runs. Wireless networks are formed around a Gateway, which acts as the wireless network master device, and one or more Nodes.
PAGE 2
SureCross DX80 Node Setting Up Your Wireless Network To set up and install your wireless network, follow these steps: 1. 2. 3. 4. Configure the DIP switches of all devices. Connect the sensors to the SureCross devices. Apply power to all devices. Form the wireless network by binding the Nodes to the Gateway. If the binding instructions are not included in the datasheet, refer to the product manual for binding instructions. 5.
PAGE 3
SureCross DX80 Node Switches Device Settings 1 2 3 4 5 Link loss output: zero OFF* OFF* Link loss output: one OFF ON Link loss output: hold last state ON OFF Link loss output: user configuration ON ON Inputs sourcing (PNP) OFF* Inputs sinking (NPN) ON 6 7 8 * Default configuration Address Mode The SureCross wireless devices may use one of two types of addressing modes: rotary dial addressing or extended addressing.
PAGE 4
SureCross DX80 Node DX80...C Wiring Wiring power to the DX80...C models varies depending the power requirements of the model. Connecting dc power to the communication pins (Tx/Rx) will cause permanent damage. For FlexPower devices, do not apply more than 5.5V to the gray wire. Terminal Label Gateway, DX85 10 to 30V dc Powered Nodes V+ 10 to 30V dc Tx/+ RS485 / D1 / B / + V- dc common (GND) Rx/- RS485 / D0 / A / - Battery Powered Nodes 10 to 30V dc dc common (GND) B+ dc common (GND) 3.6 to 5.
PAGE 5
SureCross DX80 Node LED Behavior for the Nodes After powering up and binding the Gateway and its Nodes, verify all devices are communicating properly. A Node will not sample its inputs until it is communicating with its Gateway. When testing communication between the Gateway and Node, all radios and antennas should be at least two meters apart or the communications may fail.
PAGE 6
SureCross DX80 Node Radio and General Transmit Power Housing 900 MHz: 21 dBm conducted Polycarbonate housing and rotary dial cover; polyester labels; EDPM rubber cover gasket; nitrile rubber, non2.4 GHz: 18 dBm conducted, less than or equal to 20 sulphur cured button covers dBm EIRP Weight: 0.26 kg (0.57 lbs) 900 MHz Compliance (150 mW Radios) Mounting: #10 or M5 (SS M5 hardware included) FCC ID TGUDX80 - This device complies with FCC Part 15, Subpart C, 15.247 Max. Tightening Torque: 0.
PAGE 7
SureCross DX80 Node Environmental and Certifications Shock and Vibration IEC 68-2-6 and IEC 68-2-7 Shock: 30g, 11 millisecond half sine wave, 18 shocks Vibration: 0.5 mm p-p, 10 to 60 Hz Refer to the SureCross DX80 Wireless I/O Network Product Manual (p/n 132607) for installation and waterproofing instructions. Operating the devices at the maximum operating conditions for extended periods can shorten the life of the device. Included with Model The following items ship with the DX80 radios.