User Manual

ManualsBrandsBanner ManualsEquipmentSureCross DX80 Wireless Networks

Printed in USA 08/09 P/N 137909 rev. A

SureCross™ DX80K Wireless Conﬁgured Kit

Discrete and analog I/O between a Gateway and 2 Nodes

WARNING . . .

Not To Be Used for Personnel Protection

Never use these products for personnel protection. Doing so could lead to serious injury or death.

These products do NOT include the self-checking redundant circuitry necessary to allow their use in personnel safety applications. A

failure or malfunction can cause either an energized or de-energized output condition. Consult your current Banner Safety Products

catalog for safety products that meet OSHA, ANSI, and IEC standards for personnel protection.

Features

The SureCross™ DX80 is a radio frequency network system built around a Gateway and one

or more Nodes. Conﬁgured kits are packaged in a box with the preset Gateway, Node(s),

accessories, and hardware to get up and running quickly.

Input-to-output mapping provides four discrete (sourcing) inputs, four discrete (sourcing) •

outputs, two analog (0–20 mA) inputs, and two analog (0–20 mA) outputs on the

Gateway mapped to two discrete (sourcing) inputs, two discrete (sourcing) outputs, one

analog (0–20 mA) input, and one analog (0–20 mA) output on each of the two Nodes

+10 to 30V dc power•

Proprietary radio optimized for effective power management•

Frequency Hopping Spread Spectrum (FHSS) technology and Time Division Multiple •

Access (TDMA) control architecture combine to ensure reliable data delivery within the

unlicensed Industrial, Scientiﬁc, and Medical (ISM) bands

Transceivers provide two-way communication between the Gateway and Node, including •

fully acknowledged data transmission

Site Survey analyzes the network’s signal strength and reliability•

Lost RF links are detected and relevant outputs set to predeﬁned conditions•

For additional information and a complete list of accessories, including FCC approved

antennas, please refer to Banner Engineering’s website, www.bannerengineering.com/

surecross.

Model Frequency Power I/O Mapping I/O Devices

DX80K9M6EM2 900 MHz ISM Band

+10 to 30V dc

Conﬁgured

(See hookup diagram)

Discrete Inputs: Four Sourcing

Discrete Outputs: Four Sourcing

Analog Inputs: Two 0–20 mA

Analog Outputs: Two 0–20 mA

One Gateway

Two Nodes

DX80K2M6EM2 2.4 GHz ISM Band

Models

Summary of content (8 pages)

PAGE 1
SureCross™ DX80K Wireless Configured Kit Discrete and analog I/O between a Gateway and 2 Nodes Features The SureCross™ DX80 is a radio frequency network system built around a Gateway and one or more Nodes. Configured kits are packaged in a box with the preset Gateway, Node(s), accessories, and hardware to get up and running quickly.
PAGE 2
SureCross™ DX80K Wireless Configured Kit Hookup Diagrams Configured input/output mapping I/O Point Terminal Block Label DX80 Gateway DX80 Node Terminal Block Label I/O Point 1 DI1 Discrete IN 1 Discrete OUT 1 DO1 9 2 DI2 Discrete IN 2 Discrete OUT 2 DO2 10 3 DI3 Discrete IN 3 Discrete OUT 1 DO1 9 4 DI4 Discrete IN 4 Discrete OUT 2 DO2 10 5 AI1 Analog IN 1 Analog OUT 1 AO1 13 Node 1 6 AI2 Analog IN 2 Analog OUT 2 AO2 14 Node 2 Node 1 Node 2 DO1 Discrete OUT 1 Di
PAGE 3
SureCross™ DX80K Wireless Configured Kit Device Configuration Cycle Power After making any changes to the DIP switch positions, cycle power to the device to activate the changes. For devices with batteries integrated into the housing, remove the battery for one minute to cycle power to the device. Device Settings 1 Rotary Switch Address Mode OFF Extended Address Mode ON Switches 2 3 4 Do not change the position of any DIP switch other than DIP switch 1. This kit is configured at the factory.
PAGE 4
SureCross™ DX80K Wireless Configured Kit Rotary Dial Positions Rotary Dial Addressing Mode When using Rotary Dial Addressing Mode, the Gateway’s and Node’s rotary dials are in the correct position. The left rotary dial establishes the Network ID and the right dials establish the Device ID. When using multiple networks within range of each other, set each network to a different Network ID using the left rotary dial.
PAGE 5
SureCross™ DX80K Wireless Configured Kit Specifications Many parameters are configurable. The values in the tables represent factory defaults unless otherwise noted. Radio Range* 900 MHz: Up to 4.8 kilometers (3 miles) 2.4 GHz: Up to 3.2 kilometers (2 miles) Transmit Power 900 MHz: 21 dBm Conducted 2.4 GHz: 18 dBm Conducted, ≤ 20 dBm EIRP Spread Spectrum Technology FHSS (Frequency Hopping Spread Spectrum) Antenna Connector Ext. Reverse Polarity SMA, 50 Ohms Antenna Max. Tightening Torque 0.
PAGE 6
SureCross™ DX80K Wireless Configured Kit Outputs * Discrete Outputs Gateway: Four Sourcing Node: Two Sourcing Discrete Output Rating 100 mA max current at 30V dc ON-State Saturation: Less than 3V at 100 mA OFF-state Leakage: Less than 10 µA Discrete Output ON Condition Supply minus 2V Discrete Output OFF Condition Less than 2V Discrete Output State Following Timeout De-energized (OFF) Analog Outputs Gateway: Two, 0 to 20 mA Node: One, 0 to 20 mA Discrete, Analog Update Rate 62.
PAGE 7
SureCross™ DX80K Wireless Configured Kit Notes Banner Engineering Corp. • Minneapolis, MN U.S.A www.bannerengineering.com • Tel: 763.544.3164 P/N 137909 rev.
PAGE 8
SureCross™ DX80K Wireless Configured Kit For more information: Contact your local Banner representative or Banner Corporate Offices around the world. Corporate Headquarters Banner Engineering Corp. 9714 Tenth Ave. North Mpls., MN 55441 Tel: 763-544-3164 www.bannerengineering.com sensors@bannerengineering.com Asia ─ China Banner Engineering China Shanghai Rep Office Rm. G/H/I, 28th Flr. Cross Region Plaza No. 899, Lingling Road Shanghai 200030 CHINA Tel: 86-21-54894500 Fax: 86-21-54894511 www.