Manual

ManualsBrandsBanner ManualsEquipmentSureCross DX80 Wireless Networks

Configurable Gateway with discrete and analog inputs and outputs

IP67 Base

2.4 GHz

IP20 Base

900 MHz

Internal antenna models are also

available, but are not UL Listed. For

more information, contact your local

Banner Engineering Corp. represen-

tative.

The SureCross® wireless system is a radio frequency network with integrated I/O that can oper-

ate in most environments and eliminate the need for wiring runs. Wireless networks are formed

around a Gateway, which acts as the wireless network master device, and one or more Nodes.

• Wireless industrial I/O device with four selectable discrete inputs, four sourcing discrete out-

puts, two 0 to 20 mA analog inputs, and two 0 to 20 mA analog outputs

• 10 to 30V dc power input

• DIP switches for user configuration

• Modbus serial interface

• Site Survey analyzes the network’s signal strength and reliability and displays the results on

the Gateway's LCD

• Frequency Hopping Spread Spectrum (FHSS) technology and Time Division Multiple Access

(TDMA) control architecture ensure reliable data delivery within the unlicensed Industrial, Sci-

entific, and Medical (ISM) band

• Transceivers provide bidirectional communication between the Gateway and Node, including

fully acknowledged data transmission

• Lost RF links are detected and relevant outputs set to user-defined conditions

• The DX80...C models are certified for use in Class I, Division 2, Group A, B, C, D; Zone 2

(Category 3G) Hazardous Locations when properly installed in accordance with the National

Electrical Code, the Canadian Electrical Code, or applicable local codes/regulations (see

Specifications)

Model Frequency Environmental Rating I/O

DX80G9M6S4P4M2M2

900 MHz ISM

Band

IP67, NEMA 6

Inputs: Four selectable discrete, two 0 to 20 mA

analog

Outputs: Four sourcing discrete, two 0 to 20 mA

analog

DX80G2M6S4P4M2M2 2.4 GHz ISM Band

DX80G9M6S4P4M2M2C

900 MHz ISM

Band

IP20, NEMA 1

Class I, Division 2, Group A, B,

C, D Hazardous Locations (see

Specifications)

DX80G2M6S4P4M2M2C 2.4 GHz ISM Band

WARNING: Not To Be Used for Personnel Protection

Never use this device as a sensing device for personnel protection. Doing so could lead to serious

injury or death. This device does not include the self-checking redundant circuitry necessary to allow its

use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de-

energized sensor output condition.

The SureCross® DX80 Wireless Network

Gateway

Node

FlexPower Node

and Battery Supply Module

The SureCross® DX80 wireless I/O network provides reliable moni-

toring without wiring or conduit installation. The SureCross wireless

network operates independently or in conjunction with a host system,

PLC, and/or PC software.

Each wireless network system consists of one Gateway and one or

more Nodes. Devices ship with factory-defined discrete, analog, or a

mix of discrete and analog inputs and outputs.

The SureCross® DX80 network is a deterministic system—the net-

work identifies when the radio signal is lost and drives relevant out-

SureCross DX80 Gateway with Discrete and Analog I/O

P/N 131935 Rev. H 5/23/2013

0 131935 4

Summary of content (8 pages)

PAGE 1
SureCross DX80 Gateway with Discrete and Analog I/O Configurable Gateway with discrete and analog inputs and outputs The SureCross® wireless system is a radio frequency network with integrated I/O that can operate in most environments and eliminate the need for wiring runs. Wireless networks are formed around a Gateway, which acts as the wireless network master device, and one or more Nodes.
PAGE 2
SureCross DX80 Gateway with Discrete and Analog I/O puts to user-defined conditions. After the radio signal is reacquired, the network returns to normal operation. SureCross® DX80 Gateways and Nodes A Gateway is the master device within each radio network. Every wireless network must have one Gateway, which schedules communication traffic and controls the I/O configuration for the network, and one or more Nodes.
PAGE 3
SureCross DX80 Gateway with Discrete and Analog I/O 1. 2. 3. 4. Unscrew the four screws that mount the cover to the bottom housing. Remove the cover from the housing without damaging the ribbon cable or the pins the cable plugs into. Gently unplug the ribbon cable from the board mounted into the bottom housing. Remove the black cover plate from the bottom of the device's cover. The DIP switches are located behind the rotary dials.
PAGE 4
SureCross DX80 Gateway with Discrete and Analog I/O Modbus/User Configuration Tool (UCT) or DIP Switch Configured In Modbus/UCT Configured mode, the device parameters are changed using the User Configuration Tool (UCT) or a Modbus command. All DIP switch positions are ignored. In DIP Switch Configured mode, use the DIP switches to configure the parameters listed in the table.
PAGE 5
SureCross DX80 Gateway with Discrete and Analog I/O PNP Discrete Inputs + + NPN Discrete Inputs DI1 DI2 DI3 DI4 AI1 AI2 V+ VV- − − + 10-30V dc − DO1 DO2 DO3 DO4 AO1 Load Load Load Load AO2 Tx/+ Rx/V+ + − + − + 10-30V dc − RS-485+ RS-485− AIx or Ax. Analog IN x. AOx. Analog OUT x. DI1 DI2 DI3 DI4 AI1 AI2 V+ VV- DO1 DO2 DO3 DO4 AO1 Load Load Load Load AO2 Tx/+ Rx/V+ RS-485+ RS-485− PWR. Power, 10 to 30V dc power connection. RX/-. Serial comms line TX/+. Serial comms line V+.
PAGE 6
SureCross DX80 Gateway with Discrete and Analog I/O I/O Modbus Holding Register I/O Type Units Gateway or DX85 Any Node 8 8 8 + (Node# × 16) Device Message 9 9 9 + (Node# × 16) Discrete OUT 1 10 10 10 + (Node# × 16) 11 11 12 I/O Range Holding Register Representation Terminal Block Labels Min. Value Max. Val- Min. ue (Dec.) Max. (Dec.
PAGE 7
SureCross DX80 Gateway with Discrete and Analog I/O Inputs and Outputs Discrete Inputs Rating: 3 mA max current at 30V dc Sample Rate: 62.5 milliseconds Report Rate: On change of state Discrete Input ON Condition PNP: Greater than 8V NPN: Less than 0.7V Discrete Input OFF Condition PNP: Less than 5V NPN: Greater than 2V or open Analog Inputs Rating: 24 mA Impedance: 100 Ohms Sample Rate: 62.5 milliseconds Report Rate: 1 second or On Change of State (1% change in value) Accuracy: 0.1% of full scale +0.
PAGE 8
SureCross DX80 Gateway with Discrete and Analog I/O • BWA-HW-002: DX80 Access Hardware Kit, containing four PG-7 plastic threaded plugs, four PG-7 nylon gland fittings, four PG-7 hex nuts, one 1/2-inch NPT plug, and one 1/2-inch nylon gland fitting. (Not included with IP20 DX80...C models) • BWA-HW-001: Mounting Hardware Kit, containing four M5-0.8 x 25mm SS screws, four M5-0.8 x 16mm SS screws, four M5-0.