Owner manual

ManualsBrandsBanner ManualsEquipmentSureCross DX80 Wireless Networks

Configurable Node with switched power outputs, discrete inputs, discrete NMOS outputs, and analog inputs

IP67 Base

2.4 GHz

IP20 Base

900 MHz

For additional information, updated

documentation, and accessories,

refer to Banner Engineering's web-

site, www.bannerengineering.com/

surecross.

The SureCross® wireless system is a radio frequency network with integrated I/O that can oper-

ate in most environments and eliminate the need for wiring runs. Wireless networks are formed

around a Gateway, which acts as the wireless network master device, and one or more Nodes.

• Wireless industrial I/O device with two discrete inputs, two discrete (NMOS sinking) outputs

when configured for discrete mode; two discrete inputs, two discrete outputs, and two analog

inputs when configured for analog mode

• FlexPower® power options allows for +10 to 30V dc, solar, and battery power sources for low

power applications.

• DIP switches for user configuration

• Multiple switched power outputs can be switch configured to provide sensor actuation voltage

from the battery supply

• Frequency Hopping Spread Spectrum (FHSS) technology and Time Division Multiple Access

(TDMA) control architecture ensure reliable data delivery within the unlicensed Industrial, Sci-

entific, and Medical (ISM) band

• Transceivers provide bidirectional communication between the Gateway and Node, including

fully acknowledged data transmission

• Lost RF links are detected and relevant outputs set to user-defined conditions

• The DX80...C models are certified for use in Class I, Division 2, Group A, B, C, D; Zone 2

(Category 3G) Hazardous Locations when properly installed in accordance with the National

Electrical Code, the Canadian Electrical Code, or applicable local codes/regulations (see

Specifications)

Models (0-20 mA Analog

Inputs)

Frequency Environmental Rat-

ing

Inputs and Outputs

DX80N9X2S2N2M2

900 MHz ISM

Band

IP67, NEMA 6

Discrete Mode

Inputs: Two selectable discrete

Outputs: Two NMOS discrete

Switch Power: Two, Configurable

Analog Mode

Inputs: Two selectable discrete, two 0

to 20 mA analog

Outputs: Two NMOS discrete

Switch Power: One, Configurable

DX80N2X2S2N2M2

2.4 GHz ISM

Band

DX80N9X2S2N2M2C

900 MHz ISM

Band

IP20, NEMA 1

DX80N2X2S2N2M2C

2.4 GHz ISM

Band

Models (0-10V Analog

Inputs)

Frequency Environmental Rat-

ing

Inputs and Outputs

DX80N9X2S2N2V2

900 MHz ISM

Band

IP67, NEMA 6

Discrete Mode

Inputs: Two selectable discrete

Outputs: Two NMOS discrete

Switch Power: Two, Configurable

Analog Mode

Inputs: Two selectable discrete, two 0

to 10V analog

Outputs: Two NMOS discrete

Switch Power: One, Configurable

DX80N2X2S2N2V2

2.4 GHz ISM

Band

DX80N9X2S2N2V2C

900 MHz ISM

Band

IP20, NEMA 1

DX80N2X2S2N2V2C

2.4 GHz ISM

Band

Internal antenna models are also available. For more information, contact your local Banner Engineering Corp. representative.

SureCross DX80 FlexPower Node

P/N 131296 Rev. L 5/21/2013

0 131296 6

Summary of content (10 pages)

PAGE 1
SureCross DX80 FlexPower Node Configurable Node with switched power outputs, discrete inputs, discrete NMOS outputs, and analog inputs The SureCross® wireless system is a radio frequency network with integrated I/O that can operate in most environments and eliminate the need for wiring runs. Wireless networks are formed around a Gateway, which acts as the wireless network master device, and one or more Nodes.
PAGE 2
SureCross DX80 FlexPower Node WARNING: Not To Be Used for Personnel Protection Never use this device as a sensing device for personnel protection. Doing so could lead to serious injury or death. This device does not include the self-checking redundant circuitry necessary to allow its use in personnel safety applications. A sensor failure or malfunction can cause either an energized or deenergized sensor output condition.
PAGE 3
SureCross DX80 FlexPower Node After making the necessary changes to the DIP switches, place the black cover plate back into position and gently push into place. Plug the ribbon cable in after verifying that the blocked hole lines up with the missing pin. Mount the cover back onto the housing.
PAGE 4
SureCross DX80 FlexPower Node Analog Configuration, Switch 2 OFF Descriptions DIP Switches 3 4 5 6 7 8 Sample/Report Rate 64 seconds ON OFF OFF Sample/Report Rate 5 minutes ON OFF ON Modbus or UCT configured (overrides DIP switches) ON ON OFF Sample/Report Rate 15 minutes ON ON ON Analog IN 2 (not available in integrated battery model), Discrete 1, and Discrete 2 are not powered from switched power terminals. In this configuration, SP2 is disabled.
PAGE 5
SureCross DX80 FlexPower Node Wiring Your SureCross® Device Use the following wiring diagrams to first wire the sensors and then apply power to the SureCross devices. 5-pin Euro-Style Wiring (Nodes) Wiring the 5-pin Euro-style connector depends on the model and power requirements of the device. Connecting dc power to the communication pins will cause permanent damage. For FlexPower devices, do not apply more than 5.5V to the gray wire. Wire No.
PAGE 6
SureCross DX80 FlexPower Node IP67 Base IP20 Base SPx. Switch Power. Provides variable power sources for external devices. (SP3 and SP4 are not used for the factory default configuration of this model.) Wiring Diagrams for Discrete Inputs Connecting dc power to the communication pins will cause permanent damage. For the DX8x...C models, PWR in the wiring diagram refers to V+ on the wiring board and GND in the wiring diagram refers to V- on the wiring board.
PAGE 7
SureCross DX80 FlexPower Node • To reduce power consumption and extend battery life, slower sample and reporting rates are used. Faster sample and report rates can be configured, but this will decrease the battery’s life. For details, refer to the included table of DIP switch configurable parameters. • The FlexPower switched power management system can operate a FlexPower Node and a sensing device for up to five years on a single lithium D cell.
PAGE 8
SureCross DX80 FlexPower Node I/O 10 Modbus Holding Register Gateway Any Node 10 10 + (Node# × 16) I/O Type Units I/O Range Min. Discrete OUT 2 - 0 Holding Register Representation Max. Min. (Dec.) 1 0 Terminal Block Labels Max. (Dec.) 1 DO2 ... 15 15 15 + (Node# × 16) Control Message 16 16 16 + (Node# × 16) Reserved Specifications Radio and General Range Power 900 MHz: Up to 4.8 kilometers (3 miles) Requirements: +10 to 30V dc or +3.6 to 5.
PAGE 9
SureCross DX80 FlexPower Node Inputs and Outputs Analog Inputs Rating for 0 to 20 mA models: 24 mA Rating for 0 to 10V models: 10V Impedance: 100 Ohms Sample/Report Rates (Analog IN 1): DIP switch configurable (see tables) Sample/Report Rates (Analog IN 2): 1 second/16 seconds Accuracy: 0.1% of full scale +0.
PAGE 10
SureCross DX80 FlexPower Node certified for use in these countries using the antenna that ships with the product. When using other antennas, verify you are not exceeding the transmit power levels allowed by local governing agencies. Consult with Banner Engineering Corp. if the destination country is not on this list. Violating Warnings. The manufacturer does not take responsibility for the violation of any warning listed in this document.