Owner manual

ManualsBrandsBanner ManualsEquipmentSureCross DX80 Wireless Networks

Configurable Node with two discrete inputs, two discrete NMOS outputs, and four analog inputs

IP67 Base

2.4 GHz

IP20 Base

900 MHz

For additional information, updated docu-

mentation, and accessories, refer to

Banner Engineering's website, www.ban-

nerengineering.com/surecross.

The SureCross® wireless system is a radio frequency network with integrated I/O that can

operate in most environments and eliminate the need for wiring runs. Wireless networks are

formed around a Gateway, which acts as the wireless network master device, and one or

more Nodes.

• Wireless industrial I/O device with two selectable discrete inputs, two NMOS discrete

outputs, and four 0 to 20 mA analog inputs

• FlexPower® power options allows for +10 to 30V dc, solar, and battery power sources

for low power applications.

• DIP switches for user configuration

• Frequency Hopping Spread Spectrum (FHSS) technology and Time Division Multiple Ac-

cess (TDMA) control architecture ensure reliable data delivery within the unlicensed In-

dustrial, Scientific, and Medical (ISM) band

• Transceivers provide bidirectional communication between the Gateway and Node, in-

cluding fully acknowledged data transmission

• Lost RF links are detected and relevant outputs set to user-defined conditions

• The DX80...C models are certified for use in Class I, Division 2, Group A, B, C, D; Zone

2 (Category 3G) Hazardous Locations when properly installed in accordance with the

National Electrical Code, the Canadian Electrical Code, or applicable local codes/regula-

tions (see Specifications)

Models Frequency Environmental Rating I/O

DX80N9X2S2N2M4 900 MHz

IP67, NEMA 6

Inputs: Two selectable discrete, four 0 to 20 mA

analog

Outputs: Two NMOS sinking discrete

DX80N2X2S2N2M4 2.4 GHz

DX80N9X2S2N2M4C 900 MHz IP20, NEMA 1

Class I, Division 2, Group A, B, C, D

Hazardous Locations (see Specifica-

tions)

DX80N2X2S2N2M4C 2.4 GHz

DX80N9X2S2N2V4 900 MHz

IP67, NEMA 6

Inputs: Two selectable discrete, four 0 to 10V

analog

Outputs: Two NMOS sinking discrete

DX80N2X2S2N2V4 2.4 GHz

DX80N9X2S2N2V4C 900 MHz IP20, NEMA 1

Class I, Division 2, Group A, B, C, D

Hazardous Locations (see Specifica-

tions)

DX80N2X2S2N2V4C 2.4 GHz

Internal antenna models are also available. For more information, contact your local Banner Engineering Corp. representative.

WARNING: Not To Be Used for Personnel Protection

Never use this device as a sensing device for personnel protection. Doing so could lead to serious

injury or death. This device does not include the self-checking redundant circuitry necessary to allow its

use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de-

energized sensor output condition.

SureCross DX80 FlexPower Node

P/N 131762 Rev. I 5/21/2013

0 131762 0

Summary of content (8 pages)

PAGE 1
SureCross DX80 FlexPower Node Configurable Node with two discrete inputs, two discrete NMOS outputs, and four analog inputs The SureCross® wireless system is a radio frequency network with integrated I/O that can operate in most environments and eliminate the need for wiring runs. Wireless networks are formed around a Gateway, which acts as the wireless network master device, and one or more Nodes.
PAGE 2
SureCross DX80 FlexPower Node SureCross User Configuration Tool The User Configuration Tool (UCT) offers an easy way to link I/O points in your wireless network, view I/O register values graphically, and set system communication parameters when a host system is not part of the wireless network. The UCT requires a special USB to RS-485 (model number BWA-UCT-900 for 1 Watt radios, BWA-HW-006 can be used for all other radios) converter cable to pass information between your computer and the Gateway.
PAGE 3
SureCross DX80 FlexPower Node DIP Switch Settings Switches Device Settings 1 4 5 Link loss output: zero OFF* OFF* Link loss output: one OFF ON Link loss output: hold last state ON OFF Link loss output: user configuration ON ON Rotary dial address mode OFF* Extended address mode ON Modbus or UCT configured (overrides DIP switches 3-8) DIP switch configured 2 3 6** 7 8 OFF* ON Inputs sinking (NPN) OFF* Inputs sourcing (PNP) ON 0–20 mA scale (Not used on 0-10V analog models) OF
PAGE 4
SureCross DX80 FlexPower Node Wiring Your SureCross® Device Use the following wiring diagrams to first wire the sensors and then apply power to the SureCross devices. 5-pin Euro-Style Wiring (Nodes) Wiring the 5-pin Euro-style connector depends on the model and power requirements of the device. Connecting dc power to the communication pins will cause permanent damage. For FlexPower devices, do not apply more than 5.5V to the gray wire. Wire No.
PAGE 5
SureCross DX80 FlexPower Node Wiring Diagrams for Discrete Inputs Connecting dc power to the communication pins will cause permanent damage. For the DX8x...C models, PWR in the wiring diagram refers to V+ on the wiring board and GND in the wiring diagram refers to V- on the wiring board.
PAGE 6
SureCross DX80 FlexPower Node I/O Modbus Holding Register I/O Type Units Gateway Any Node 1 1 1 + (Node# × 16) Discrete IN 1 - 2 2 2 + (Node# × 16) Discrete IN 2 3 3 3 + (Node# × 16) 4 4 5 I/O Range Min. Holding Register Representation Terminal Block Labels Max. Min. (Dec.) Max. (Dec.) 0 1 0 1 DI1 - 0 1 0 1 DI2 Analog IN 1+ mA / V 0.0 20.0 / 10.0 0 65535 A1+ 4 + (Node# × 16) Analog IN 2+ mA / V 0.0 20.0 / 10.
PAGE 7
SureCross DX80 FlexPower Node Radio and General Radio range is with the 2 dB antenna that ships with the product. For European applications, power the DX80 from a Limited Power High-gain antennas are available, but the range depends on the Source as defined in EN 60950-1. environment and line of sight. To determine the range of your wireless network, perform a Site Survey.
PAGE 8
SureCross DX80 FlexPower Node • BWA-HW-001: Mounting Hardware Kit, containing four M5-0.8 x 25mm SS screws, four M5-0.8 x 16mm SS screws, four M5-0.8mm SS hex nuts, and four #8-32 x 3/4" SS bolts • BWA-HW-003: PTFE tape • BWA-9O2-C (900 MHz) or BWA-2O2-C (2.4 GHz): Antenna, 2 dBd Omni, Rubber Swivel RP-SMA Male.