User Manual

ManualsBrandsBanner ManualsEquipmentSureCross DX80 Wireless Networks

Configurable Node with 2 selectable counter inputs, 2 selectable discrete inputs, and 2 NMOS discrete outputs

IP67 Base

2.4 GHz

IP20 Base

900 MHz

The SureCross® wireless system is a radio frequency network with integrated I/O that can oper-

ate in most environments and eliminate the need for wiring runs. Wireless networks are formed

around a Gateway, which acts as the wireless network master device, and one or more Nodes.

• Wireless industrial I/O device with two selectable discrete inputs, two selectable discrete pulse

counter inputs (rate or event; sinking, sourcing, or self-energized), and two NMOS discrete

outputs

• User selectable 10 kHz event counter(s) and/or 25 kHz rate counter

• FlexPower® power options allows for +10 to 30V dc, solar, and battery power sources for low

power applications.

• DIP switches for user configuration

• Frequency Hopping Spread Spectrum (FHSS) technology and Time Division Multiple Access

(TDMA) control architecture ensure reliable data delivery within the unlicensed Industrial, Sci-

entific, and Medical (ISM) band

• Transceivers provide bidirectional communication between the Gateway and Node, including

fully acknowledged data transmission

• Lost RF links are detected and relevant outputs set to user-defined conditions

• The DX80...C models are certified for use in Class I, Division 2, Group A, B, C, D; Zone 2

(Category 3G) Hazardous Locations when properly installed in accordance with the National

Electrical Code, the Canadian Electrical Code, or applicable local codes/regulations (see

Specifications)

For additional information, updated documentation, and accessories, refer to Banner Engineering's website, www.bannerengineer-

ing.com/surecross.

Models Frequency Environmental Rating I/O

DX80N9X2S4A2 900 MHz ISM Band

IP67, NEMA 6

Inputs: Two selectable discrete, two se-

lectable counter

Outputs: Two NMOS sinking discrete

DX80N2X2S4A2 2.4 GHz ISM Band

DX80N9X2S4A2C 900 MHz ISM Band IP20, NEMA 1

Class I, Division 2, Group A, B, C, D Haz-

ardous Locations (see Specifications)

DX80N2X2S4A2C 2.4 GHz ISM Band

Internal antenna models are also available. For more information, contact your local Banner Engineering Corp. representative.

WARNING: Not To Be Used for Personnel Protection

Never use this device as a sensing device for personnel protection. Doing so could lead to serious

injury or death. This device does not include the self-checking redundant circuitry necessary to allow its

use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de-

energized sensor output condition.

SureCross User Configuration Tool

The User Configuration Tool (UCT) offers an easy way to link I/O points in your wire-

less network, view I/O register values graphically, and set system communication pa-

rameters when a host system is not part of the wireless network.

The UCT requires a special USB to RS-485 (model number BWA-UCT-900 for 1 Watt

radios, BWA-HW-006 can be used for all other radios) converter cable to pass infor-

mation between your computer and the Gateway. Download the most recent revi-

sions of the UCT software from Banner Engineering's website: http://www.banneren-

gineering.com/wireless.

SureCross DX80 FlexPower Counter Node

P/N 136348 Rev. G 5/22/2013

0 136348 7

Summary of content (12 pages)

PAGE 1
SureCross DX80 FlexPower Counter Node Configurable Node with 2 selectable counter inputs, 2 selectable discrete inputs, and 2 NMOS discrete outputs IP67 Base 2.4 GHz IP20 Base 900 MHz The SureCross® wireless system is a radio frequency network with integrated I/O that can operate in most environments and eliminate the need for wiring runs. Wireless networks are formed around a Gateway, which acts as the wireless network master device, and one or more Nodes.
PAGE 2
SureCross DX80 FlexPower Counter Node Setting Up Your Wireless Network To set up and install your wireless network, follow these steps: 1. 2. 3. 4. Configure the DIP switches of all devices. Connect the sensors to the SureCross devices. Apply power to all devices. Form the wireless network by binding the Nodes to the Gateway. If the binding instructions are not included in the datasheet, refer to the product manual for binding instructions. 5.
PAGE 3
SureCross DX80 FlexPower Counter Node Address Mode The SureCross wireless devices may use one of two types of addressing modes: rotary dial addressing or extended addressing. In rotary dial address mode, the left rotary dial establishes the network ID and the right rotary dial sets the device ID. The wireless network is restricted to a maximum of 16 devices. Extended address mode uses a security code to "bind" Nodes to a specific Gateway.
PAGE 4
SureCross DX80 FlexPower Counter Node * Default configuration Debounce establishes how to examine a signal’s transitions. The factory default setting is to activate the input filtering to compensate for unclean state transitions. To turn off the input filtering, set the switch to the ON position. Device switches Inputs. Counter switches 6 and 7 define the inputs as self-energized, sinking (NPN), or sourcing (PNP). A self-energized input does not require pull-up or pull-down devices for proper operation.
PAGE 5
SureCross DX80 FlexPower Counter Node Terminal Block (IP67 Housing) AXN, AXP. Not used. Do not make any wiring connections to these terminals. CIx. Counter IN x. DIx. Discrete IN x. DOx. Discrete OUT x. GND. Ground/dc common connection. PWR. Power, 10 to 30V dc power connection. TIN, TIP. Not used. Do not make any wiring connections to these terminals. Ignore alternate labeling referring to other models that use this board.
PAGE 6
SureCross DX80 FlexPower Counter Node Discrete Output Wiring (NPN or NMOS) PWR 10-30V dc DOx Load GND dc common Wiring Diagrams for Counter Inputs Connecting dc power to the communication pins will cause permanent damage. For the DX8x...C models, PWR in the wiring diagram refers to V+ on the wiring board and GND in the wiring diagram refers to V- on the wiring board.
PAGE 7
SureCross DX80 FlexPower Counter Node I/O Modbus Holding Register I/O Type I/O Range Holding Register Representation Min. Max. Min. (Dec.) Clear Counter 1 0 1 0 1 Clear Counter 2 0 1 0 1 Gateway Any Node 11 11 11 + (Node# × 16) 12 12 12 + (Node# × 16) 13 13 13 + (Node# × 16) 14 14 14 + (Node# × 16) 15 15 15 + (Node# × 16) Control Message 16 16 16 + (Node# × 16) Reserved Terminal Block Labels Max. (Dec.
PAGE 8
SureCross DX80 FlexPower Counter Node I/O Modbus Holding Register Gateway Any Node 16 16 + (Node# × 16) 16 I/O Type I/O Range Min. Holding Register Representation Max. Min. (Dec.) Terminal Block Labels Max. (Dec.) Reserved ** Two consecutive 16-bit unsigned registers are combined to represent one 32-bit unsigned number for a maximum total count of 4,294,967,295.
PAGE 9
SureCross DX80 FlexPower Counter Node Node Reg 39 0x8F 2 The counter has been preset to 20,567,001 (0x0139 D3D9) Preset Using the Node’s Menu System To manually enter a counter preset, follow the LCD menu flow using the diagram shown. 1. Single click button 1 to move across the top level menus. Click button 1 until the display shows IOCFG. 2. Click button 2 to enter the I/O Configuration submenu structure. 3. Single click button 1 to move across the I/O points.
PAGE 10
SureCross DX80 FlexPower Counter Node Radio and General Range Power 900 MHz: Up to 4.8 kilometers (3 miles) Requirements: +10 to 30V dc or +3.6 to 5.5V dc low power option (Outside the USA: +12 to 24V dc, ±10% 2.4 GHz: Up to 3.2 kilometers (2 miles) or +3.6 to 5.5V dc low power option) Transmit Power Consumption: Less than 1.4 W (60 mA) at 24V dc 900 MHz: 21 dBm conducted Housing 2.
PAGE 11
SureCross DX80 FlexPower Counter Node Environmental and Certifications Rating DX80 Models:IEC IP67; NEMA 6; (See UL section below for any applicable UL specifications) DX80...C Models: IEC IP20; NEMA 1 (In a suitable enclosure: Class I, Division 2, Group A, B, C, D; T4 −40 to 80 °C) Operating Conditions Temperature: −40 to +85 °C (Electronics); −20 to +80 °C (LCD) Humidity: 95% max.
PAGE 12
SureCross DX80 FlexPower Counter Node THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE. This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP.