Owner manual

ManualsBrandsBanner ManualsEquipmentSureCross DX80 Wireless Networks

Printed in USA 08/09 P/N 129323 rev. E

SureCross™ DX80K Wireless Conﬁgured

FlexPower™ Kit

I/O Repeater Kit with discrete and analog inputs from 1 Node (with switched

power output ) to another Node

WARNING . . .

Not To Be Used for Personnel Protection

Never use these products for personnel protection. Doing so could lead to serious injury or death.

These products do NOT include the self-checking redundant circuitry necessary to allow their use in personnel safety applications. A

failure or malfunction can cause either an energized or de-energized output condition. Consult your current Banner Safety Products

catalog for safety products that meet OSHA, ANSI, and IEC standards for personnel protection.

Model Frequency Power I/O Mapping I/O Devices

DX80K9R3GE1 900 MHz ISM Band

10 to 30V dc (Gateway and Node)

3.6V dc Battery (FlexPower Node)

Gateway as I/O Repeater

(See hookup diagram)

Discrete In (Sinking)

Discrete Out (Sourcing)

Analog (0-20 mA)

1 Gateway

2 Nodes

1 Battery Module

DX80K2R3GE1 2.4 GHz ISM Band

Models

Features

The SureCross™ DX80 is a radio frequency network system built around a Gateway and one

or more Nodes. Conﬁgured kits are packaged in a box with the preset Gateway, Node(s),

accessories, and hardware to get up and running quickly. In this conﬁgured kit, the Gateway

functions as the I/O repeater.

Kit contains 10 to 30V dc Gateway, • FlexPower™ Node, 10 to 30V dc Node, and DX81

FlexPower supply module for powering one Node and switched power output of sensor

Input-to-output mapping connects the • FlexPower Node’s two discrete (sinking) and two

analog (0–20 mA) inputs with the 10 to 30V dc Node’s two discrete (sourcing) and two

analog (0–20 mA) outputs

Node-to-Gateway-to-Node conﬁguration extends the range of the wireless network•

Proprietary radio optimized for effective power management•

Frequency Hopping Spread Spectrum (FHSS) technology and Time Division Multiple •

Access (TDMA) control architecture combine to ensure reliable data delivery within the

unlicensed Industrial, Scientiﬁc, and Medical (ISM) bands

Transceivers provide two-way communication between the Gateway and Node, including •

fully acknowledged data transmission

Site Survey analyzes the network’s signal strength and reliability•

Lost RF links are detected and relevant outputs set to predeﬁned conditions•

For additional information and a complete list of accessories, including FCC approved

antennas, please refer to Banner Engineering’s website, www.bannerengineering.com/

surecross.

Summary of content (8 pages)

PAGE 1
SureCross™ DX80K Wireless Configured FlexPower™ Kit I/O Repeater Kit with discrete and analog inputs from 1 Node (with switched power output ) to another Node Features The SureCross™ DX80 is a radio frequency network system built around a Gateway and one or more Nodes. Configured kits are packaged in a box with the preset Gateway, Node(s), accessories, and hardware to get up and running quickly. In this configured kit, the Gateway functions as the I/O repeater.
PAGE 2
SureCross™ DX80K Wireless Configured FlexPower™ Kit PWR PWR Hookup Diagrams DI1 GND GND DI2 DO1 DO2 AO2 AO1 GND GND AI2 AI1 SP3 SP4 PWR PWR GND GND GND GND A1+ A2+ DO2 DO1 DI2 A1− A2− DI1 QT50U Power Gateway as Repeater SP1 SP2 Configured input/output mapping I/O Point Terminal Block Label DX80 Node 1 DX80 Node 2 Terminal Block Label I/O Point 9 DO1 Discrete OUT 1 Discrete IN 1 DI1 1 10 DO2 Discrete OUT 2 Discrete IN 2 DI2 2 13 AO1 Analog OUT 1 Analog IN 1+ A1+ 3
PAGE 3
SureCross™ DX80K Wireless Configured FlexPower™ Kit FlexPower™ Device Configuration Cycle Power After making any changes to the DIP switch positions, cycle power to the device to activate the changes. For devices with batteries integrated into the housing, remove the battery for one minute to cycle power to the device. Do not change the position of any DIP switch other than DIP switches 1 and 2. This kit is configured at the factory.
PAGE 4
SureCross™ DX80K Wireless Configured FlexPower™ Kit Analog Configuration (Default configuration) For analog configuration, DIP switch 2 is in the OFF position. Analog configuration has analog IN 1 linked to switch power 1 (SP1) and is programmable using switches four through eight. Analog input 2 uses the report rate and sample intervals listed in the table below. Discrete inputs 1 and 2 are also active in this configuration and the input types are defined using switch 3.
PAGE 5
SureCross™ DX80K Wireless Configured FlexPower™ Kit Rotary Dial Positions Rotary Dial Addressing Mode When using Rotary Dial Addressing Mode, the Gateway’s and Node’s rotary dials are in the correct position. The left rotary dial establishes the Network ID and the right dials establish the Device ID. When using multiple networks within range of each other, set each network to a different Network ID using the left rotary dial.
PAGE 6
SureCross™ DX80K Wireless Configured FlexPower™ Kit Specifications Many parameters are configurable. The values in the tables represent factory defaults unless otherwise noted. Radio Range* 900 MHz: Up to 4.8 kilometers (3 miles) 2.4 GHz: Up to 3.2 kilometers (2 miles) Transmit Power 900 MHz: 21 dBm Conducted 2.4 GHz: 18 dBm Conducted, ≤ 20 dBm EIRP Spread Spectrum Technology FHSS (Frequency Hopping Spread Spectrum) Antenna Connector Ext. Reverse Polarity SMA, 50 Ohms Antenna Max.
PAGE 7
SureCross™ DX80K Wireless Configured FlexPower™ Kit Outputs * Discrete Outputs Two Sourcing Discrete Output Rating 100 mA max current at 30V dc ON-State Saturation: Less than 3V at 100 mA OFF-state Leakage: Less than 10 µA Discrete Output ON Condition Supply minus 2V Discrete Output OFF Condition Less than 2V Analog Outputs Two, 0 to 20 mA Maximum End-to-end Latency* 450 milliseconds Output State Following Timeout De-energized (OFF) From the sample point and with a good RF signal.
PAGE 8
SureCross™ DX80K Wireless Configured FlexPower™ Kit For more information: Contact your local Banner representative or Banner Corporate Offices around the world. Corporate Headquarters Banner Engineering Corp. 9714 Tenth Ave. North Mpls., MN 55441 Tel: 763-544-3164 www.bannerengineering.com sensors@bannerengineering.com Asia ─ China Banner Engineering China Shanghai Rep Office Rm. G/H/I, 28th Flr. Cross Region Plaza No. 899, Lingling Road Shanghai 200030 CHINA Tel: 86-21-54894500 Fax: 86-21-54894511 www.