Instruction Manual

ManualsBrandsBanner ManualsEquipmentSureCross DX80 Wireless Networks

Configurable Node with analog inputs and analog outputs

IP67 Base

2.4 GHz

IP20 Base

900 MHz

The SureCross® wireless system is a radio frequency network with integrated I/O that can

operate in most environments and eliminate the need for wiring runs. Wireless networks are

formed around a Gateway, which acts as the wireless network master device, and one or

more Nodes.

• Wireless industrial I/O device with four 0 to 10V analog inputs and four 0 to 10V analog

outputs

• 10 to 30V dc power input

• DIP switches for user configuration

• Frequency Hopping Spread Spectrum (FHSS) technology and Time Division Multiple Ac-

cess (TDMA) control architecture ensure reliable data delivery within the unlicensed Indus-

trial, Scientific, and Medical (ISM) band

• Transceivers provide bidirectional communication between the Gateway and Node, includ-

ing fully acknowledged data transmission

• Lost RF links are detected and relevant outputs set to user-defined conditions

• The DX80...C models are certified for use in Class I, Division 2, Group A, B, C, D; Zone 2

(Category 3G) Hazardous Locations when properly installed in accordance with the Na-

tional Electrical Code, the Canadian Electrical Code, or applicable local codes/regulations

(see Specifications)

For additional information, updated documentation, and accessories, refer to Banner Engineering's website, www.bannerengineer-

ing.com/surecross.

Models Frequency Environmental Rating I/O

DX80N9X6S0P0V4V4 900 MHz ISM Band

IP67, NEMA 6

Inputs: Four 0 to 10V analog

Outputs: Four 0 to 10V analog

DX80N2X6S0P0V4V4 2.4 GHz ISM Band

DX80N9X6S0P0V4V4C 900 MHz ISM Band IP20, NEMA 1

Class I, Division 2, Group A, B, C, D

Hazardous Locations (see Specifica-

tions)

DX80N2X6S0P0V4V4C 2.4 GHz ISM Band

Internal antenna models are also available, but are not UL Listed. For more information, contact your local Banner Engineering Corp.

representative.

WARNING: Not To Be Used for Personnel Protection

Never use this device as a sensing device for personnel protection. Doing so could lead to serious

injury or death. This device does not include the self-checking redundant circuitry necessary to allow its

use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de-

energized sensor output condition.

SureCross User Configuration Tool

The User Configuration Tool (UCT) offers an easy way to link I/O points in your wire-

less network, view I/O register values graphically, and set system communication pa-

rameters when a host system is not part of the wireless network.

The UCT requires a special USB to RS-485 (model number BWA-UCT-900 for 1 Watt

radios, BWA-HW-006 can be used for all other radios) converter cable to pass infor-

mation between your computer and the Gateway. Download the most recent revi-

sions of the UCT software from Banner Engineering's website: http://www.banneren-

gineering.com/wireless.

SureCross DX80 Node

P/N 136326 Rev. E 5/22/2013

0 136326 5

Summary of content (8 pages)

PAGE 1
SureCross DX80 Node Configurable Node with analog inputs and analog outputs IP67 Base 2.4 GHz IP20 Base 900 MHz The SureCross® wireless system is a radio frequency network with integrated I/O that can operate in most environments and eliminate the need for wiring runs. Wireless networks are formed around a Gateway, which acts as the wireless network master device, and one or more Nodes.
PAGE 2
SureCross DX80 Node Setting Up Your Wireless Network To set up and install your wireless network, follow these steps: 1. 2. 3. 4. Configure the DIP switches of all devices. Connect the sensors to the SureCross devices. Apply power to all devices. Form the wireless network by binding the Nodes to the Gateway. If the binding instructions are not included in the datasheet, refer to the product manual for binding instructions. 5.
PAGE 3
SureCross DX80 Node Switches Device Settings 1 2 3 4 5 6 Link loss output: zero OFF* OFF* Link loss output: one OFF ON Link loss output: hold last state ON OFF Link loss output: user configuration ON ON 0–20 mA scale (Not used on 0–10V I/O models.) OFF* 4–20 mA scale (Not used on 0–10V I/O models.) ON 7 8 * Default configuration Address Mode The SureCross wireless devices may use one of two types of addressing modes: rotary dial addressing or extended addressing.
PAGE 4
SureCross DX80 Node Terminal Label Gateway, DX85 10 to 30V dc Powered Nodes V+ 10 to 30V dc Tx/+ RS485 / D1 / B / + V- dc common (GND) Rx/- RS485 / D0 / A / - Battery Powered Nodes 10 to 30V dc dc common (GND) dc common (GND) B+ 3.6 to 5.5V dc Terminal Blocks Connecting dc power to the communication pins will cause permanent damage. Do not exceed analog input ratings for analog inputs. Only connect sensor outputs to analog inputs.
PAGE 5
SureCross DX80 Node Analog Output Wiring PWR 10-30V dc AOx GND sensor dc common LED Behavior for the Nodes After powering up and binding the Gateway and its Nodes, verify all devices are communicating properly. A Node will not sample its inputs until it is communicating with its Gateway. When testing communication between the Gateway and Node, all radios and antennas should be at least two meters apart or the communications may fail.
PAGE 6
SureCross DX80 Node Radio and General Range Power 900 MHz: Up to 4.8 kilometers (3 miles) Requirements: +10 to 30V dc (Outside the USA: +12 to 24V dc, ±10%). (See UL section below for any applica2.4 GHz: Up to 3.2 kilometers (2 miles) ble UL specifications) Transmit Power Consumption: Less than 1.4 W (60 mA) at 24V dc 900 MHz: 21 dBm conducted Housing 2.
PAGE 7
SureCross DX80 Node Environmental and Certifications Conditions Operating Temperature: −40 to +85 °C (Electronics); −20 to +80 °C (LCD) Operating Humidity: 95% max. relative (non-condensing) Radiated Immunity: 10 V/m, 80-2700 MHz (EN61000-6-2) Shock and Vibration IEC 68-2-6 and IEC 68-2-7 Shock: 30g, 11 millisecond half sine wave, 18 shocks Vibration: 0.5 mm p-p, 10 to 60 Hz Refer to the SureCross DX80 Wireless I/O Network Product Manual (p/n 132607) for installation and waterproofing instructions.
PAGE 8
SureCross DX80 Node This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP.