80In. High-Volume Ceiling Fan Owner’s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.
Thank you very much for choosing a Bannon™ product! For future reference, please complete the owner’s record below: Serial Number/Lot Date Code: ________________________________ Purchase Date: ____________________________________________ Save the receipt, warranty, and this manual. It is important that you read the entire manual to become familiar with this product before you begin using it. This fan is designed for certain applications only.
Table of Contents Intended Use .......................................................................................................................................... 4 Packaging Contents .............................................................................................................................. 4 Technical Specifications ...................................................................................................................... 4 Important Safety Information .................
Intended Use The Bannon 80 Inch High-Volume Ceiling Fan is designed for large, high ceiling areas such as factories, barns, ranches, gyms, and warehouses. The low electric usage is perfect for continuous use. Packaging Contents Motor (1) Blade Pack (6) Remote Control (1) Hanger Bracket & Canopy (1) Down rod (1) Hardware Packet (1) Technical Specifications Property Motor Max Current Consumption Watts Specification 120 Volt / 60 Hz AC 1.
Cluttered, wet, or dark work areas can result in injury. Using the product in confined work areas may put you dangerously close to cutting tools and rotating parts. Do not use the product where there is a risk of causing a fire or an explosion; e.g., in the presence of flammable liquids, gases, or dust. The product can create sparks, which may ignite the flammable liquids, gases, or dust. Do not allow the product to come into contact with an electrical source.
Store the product when it is not in use. Store it in a dry, secure place out of the reach of children. Inspect the tool for good working condition prior to storage and before re-use. Use only accessories that are recommended by the manufacturer for use with your product. Accessories that may be suitable for one product may create a risk of injury when used with another tool. Never use an accessory that has a lower operating speed or operating pressure than the tool itself.
To reduce the risk of injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign object between rotating blades. Attach the mounting bracket using only the hardware supplied with the outlet box. Fan is only to be mounted to an outlet box marked “Acceptable for Fan Support”. When moving or cleaning fan, turn off power at service panel and lock service disconnecting means to prevent power being turned on accidently.
PREPARING FOR INSTALLATION Unpack and inspect fan carefully to be certain all contents are included. Turn off power at fuse box to avoid possible electrical shock. DOWNROD INSTALLATION VAULTED CEILING INSTALLATION Note: May require a longer downrod for high vaulted ceilings (sold separately).
Remove the screws from the two matching holes (1) on canopy. Loosen (do not remove) the screws in the matching slots (2) on the canopy. Rotate the mounting bracket and remove from the canopy. Install mounting bracket to the outlet box in the ceiling using the screws and the washers provided with YOUR outlet box. DOWNROD ASSEMBLY (included) Remove clamp pin (1) and cross pin (2) from down rod (3). Feed motor lead wires through downrod/canopy assembly and insert downrod into downrod yoke.
Loosen the downrod ball (1) from the downrod (2) by removing the screw (3). Slide downrod ball (1) off of downrod and remove pin (2). DOWNROD PREPARATION Re-install pin into downrod. Slide the downrod ball up to the top of the downrod. Re-install the screw to secure ball to downrod. Note: Some extended downrods have a pre-drilled set-screw hole. If a pre-drilled hole is present in the extended downrod, tighten the set screw into the pre-drilled hole in the extended downrod.
will allow for hands-free wiring. Securely tighten safety wire (1) to hanger bracket (2). WIRING DIAGRAM Create a wiring connection from the housing and the motor to the remote receiver as shown above. Connect using wire nuts (provided). Once wiring step has been completed, slide the wired remote receiver (1) in between the mounting bracket (2) and the top of the down rod ball (3) for the down rod fans. SECURING CANOPY After wiring, slide the canopy up to the mounting bracket.
mounting bracket. ATTACHING BLADES TO FAN Insert the blades (5) through the slots on the motor housing as shown. Use the provided screws (1), washers (2), and bolts (3) to tighten the blades to the pre-attached blade brackets (4). Mount the transmitter holder onto the wall using the screws provided. Place the transmitter into the holder.
Before Each Use ⚠WARNING Be sure there aren’t any obstructions in the fan’s path of operation. Check that the batteries are in good condition in the remote control transmitter. Operating Instructions ⚠WARNING To reduce the risk of electric shock, or personal injury, mount to outlet box marked “acceptable for fan support of 22.7 Kg (50 lb.) or less” and use mounting screws provide with the outlet box and/or support directly from building structure.
SETTING FAN AIR FLOW Note: Be sure the slide switch is pushed firmly to one side or the other. The fan will not operate with the slide switch in the middle. To reverse the direction of the blades, slide the reverse switch (located on the top of the motor housing) to the opposite side. REMOTE CONTROL FAN OPERATION Turn on the power and check the operation of the fan. The Remote Control Transmitter controls the fan’s speeds: the lowest speed to the highest speed and OFF.
NOTE: Turn off and wait for the fan to come to a stop before changing the setting of the downward/upward slide switch. CONTROLLING MORE THAN ONE FAN WITH REMOTE CONTROL The remote control transmitter and receiver are matched at the factory. During the matching process, the same remote control transmitter can control another identical model ceiling fan. 1) Press the TIME key & “+” key simultaneously. 2) The ceiling fan will create a TIC sound twice.
Use a soft, damp cloth (water only) for cleaning, then wipe with dry cloth. Troubleshooting ⚠WARNING TURN OFF FAN AND BREAKER AT ELECTRICAL SUPPLY BEFORE ATTEMPING TO DO ANY ADJUSTMENT TO THE FAN. Failure IF FAN WOBBLES IN MOTION Possible Cause 1. Blades not secured or balanced 2. Be sure ball-to-hanger bracket is locked in place IF FAN DOES NOT START Not connected or no power supply IF FAN MAKES EXCESSIVE NOISE Mechanical or electrical interference Corrective Action UNPLUG from power source. 1a.
Parts Diagram Parts List Reference 1 2 3 4 5 6 6A 6B 6C 6D 63 7 Part Description MOUNTING BRACKET BLADES CANOPY DOWNROD FAN MOTOR HARDWARE PACK MOUNTING SCREW AND NUT BLADE SCREWS AND NUTS SCREW WIRE NUTS BLADE SCREW WASHERS REMOTE CONTROL WITH WALL BRACKET Page 17 of 20 Quantity 1 6 1 1 4 1 4 18 2 8 18 1
Replacement Parts For replacement parts and technical questions, please call Customer Service at 1-800-222-5381. Not all product components are available for replacement. The illustrations provided are a convenient reference to the location and position of parts in the assembly sequence. When ordering parts, the following information will be required: item description, item model number, item serial number/item lot date code, and the replacement part reference number.
Limited Warranty Northern Tool and Equipment Company, Inc. ("We'' or ''Us'') warrants to the original purchaser only ("You" or ''Your'') that the Bannon product purchased will be free from material defects in both materials and workmanship, normal wear and tear excepted, for a period of two years from date of purchase. The foregoing warranty is valid only if the installation and use of the product is strictly in accordance with product instructions.
Distributed by: Northern Tool & Equipment Company, Inc. Burnsville, Minnesota 55306 www.northerntool.