Push Trolley Owner’s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.
Thank you very much for choosing a Bannon™ product! For future reference, please complete the owner’s record below: Serial Number/Lot Date Code: ________________________________ Purchase Date: ____________________________________________ Save the receipt, warranty, and this manual. It is important that you read the entire manual to become familiar with this product before you begin using it. This trolley is designed for certain applications only.
Table of Contents Intended Use .......................................................................................................................................... 4 Technical Specifications ...................................................................................................................... 4 Important Safety Information ............................................................................................................... 4 Assembly Instructions .............................
Intended Use Designed for flexibility, the Bannon Push Trolley can be used on straight or curved tracks and can be installed or removed at any point along the track. Adjustment is easy - just remove one cotter pin and shift the spacers to fit your I-beam size. Technical Specifications Model Capacity (lb.) Beam Flange Min Width (in.) Beam Flange Max Width (in.) Beam Min Height (in.) Beam Max Height (in.) Min. Radius Curve (in.) Length A (in.) Length B (in.) Length C (Ø) Length D (in.
aware of the environment and ensure that the tool is used in a safe and responsible manner. Do not allow persons to operate or assemble the product until they have read this manual and have developed a thorough understanding of how it works. Do not modify this product in any way. Unauthorized modification may impair the function and/or safety and could affect the life of the product. There are specific applications for which the product was designed. Use the right tool for the job.
⚠CAUTION TROLLEY USE AND CARE Do not force the trolley. Products are safer and do a better job when used in the manner for which they are designed. Plan your work, and use the correct product for the job. Check for damaged parts before each use. Carefully check that the product will operate properly and perform its intended function. Replace damaged or worn parts immediately. Never operate the product with a damaged part. Store the product when it is not in use.
3. Place the trolley on the beam flange and tighten the nut. 4. Place the split pin into the nut to tighten the nut. Avoid sliding. 5. Place the hoist on the hanger plate. Operating Instructions ⚠WARNING Beam must be properly installed and rated for anticipated loads. Do not install trolley on beams of unknown capacity.
Do not install trolley on damaged or deformed beams. Trolleys are designed to be used with hoists of the same rated capacity. Never use a hoist with a capacity greater than the capacity of the trolley. Never subject trolley to a side pull or load. Load must be centered directly under the hoist / trolley assembly. Make sure load is stable and secure before moving. The trolley must be installed on a beam with minimum clearance (wheels to flange) of 1/16" to maximum of 1/8".
Figure 1 Maintenance Maintain the product by adopting a program of conscientious repair and maintenance in accordance with the following recommended procedures. It is recommended that the general condition of any tool be examined before it is used. Keep your tool in good repair. Keep handles dry, clean, and free from oil and grease. The following chart is based on a normal operation schedule. Maintenance Interval Maintenance Point Daily after operating Keep all parts clean and dry.
Parts Diagram Parts List Reference 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Part Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Part Description Wheel Bearing Snap Ring ø17mm Shield Snap Ring ø40mm Shaft Side Plate Split Pin ø4x50mm Nut M24 Outer Adjusting Washer Adjusting Washer 8mm Adjusting Washer 2mm Hanger Plate Name Plate Quantity 4 4 4 4 4 1 2 2 2 2 18 14 1 1 Replacement Parts For replacement parts and technical questions, please call Customer Service at 1-800-222-5381.
Limited Warranty Northern Tool and Equipment Company, Inc. ("We'' or ''Us'') warrants to the original purchaser only ("You" or ''Your'') that the Bannon product purchased will be free from material defects in both materials and workmanship, normal wear and tear excepted, for a period of two years from date of purchase. The foregoing warranty is valid only if the installation and use of the product is strictly in accordance with product instructions.
Distributed by: Northern Tool & Equipment Company, Inc. Burnsville, Minnesota 55306 www.northerntool.