User Guide

ManualsBrandsBarber Colman ManualsActuator AccessoriesAuxillary Potentiometer for MP's

Application

These actuator accessory kits are designed for

installation on MC, MF, MP, MU, and MUP type

oil-submerged gear train actuators. The accessory kits

are coupled to the rear of an actuator output shaft by

means of an interlocking drive disc.

Features

• Potentiometers provide accurate feedback of

actuator position for indication and precision control

• Adjustable differential SPDT auxiliary switches may

be adjusted to operate at any point in the actuator

stroke for maximum application flexibility

Applicable Literature

• TAC Cross-Reference Guide, F-23638

• TAC Reference Manual, F-12683

• TAC Application Manual, F-21335

• TAC Electric/Electronic Products Catalog, F-27382

• AM-348 Accessory Kit Mounting Bracket General

Instructions, F-10538

• MC-351, MC-421, MC-431, MC-4311 Three-Wire,

Two-Position Actuators General Instructions,

F-8366

• MP-3XX Series, MP-4XX Series, MP-2XXX Series,

and MP-4XXX Series Reversible and Proportional

Electric Actuators General Instructions, F-15479

Accessory Kits

General Instructions

AM-321, AM-332

AM-341, AM-342

AM-321, AM-332

AM-341, AM-342

Summary of content (8 pages)

PAGE 1
AM-321, AM-332 AM-341, AM-342 Accessory Kits General Instructions Application These actuator accessory kits are designed for installation on MC, MF, MP, MU, and MUP type oil-submerged gear train actuators. The accessory kits are coupled to the rear of an actuator output shaft by means of an interlocking drive disc.
PAGE 2
SPECIFICATIONS Outputs Auxiliary Switch: AM-321, 341, 342, Snap-action SPDT switches. AM-321 and AM-342 contain two auxiliary switches, and AM-341 contains four auxiliary switches. The setting of each switch is adjustable, using the wrench included. The differential of each switch is adjustable, with a minimum differential of 9°. Potentiometer: AM-332, 342, Spring-loaded, friction-driven copper wiper arm with a contact that rides on a uniformly wound wire resistance card.
PAGE 3
INSTALLATION Inspection Inspect the package for damage. If damaged, notify the appropriate carrier immediately. If undamaged, open the package and inspect the device for obvious damage. Return damaged products.
PAGE 4
WIRING AM-321, AM-341 and AM-342 accessory kits must be connected to Class 1 circuits unless all circuits are powered from a Class 2 circuit. Make all electrical connections in accordance with the job wiring diagram and in compliance with national and local electrical codes. ADJUSTMENTS Auxiliary Switch Adjustment Accessory kits AM-321 and AM-342 each contain two SPDT, snap-acting auxiliary switches. Accessory kit AM-341 contains four such switches.
PAGE 5
Potentiometer Adjustment Accessory kit AM-332 contains a potentiometer. This potentiometer consists of a spring-loaded, friction-driven, copper wiper arm with a contact that rides on a uniformly wound wire resistance card. The standard card has a resistance of 100 Ω, and is to be used only with a power supply which does not exceed 25 Vac. The electrical capacity of the resistance card is approximately 3 watts.
PAGE 6
DIMENSIONAL DATA 1/4" (6mm) 4-3/16" (106mm) 6-49/64" (172mm) 4" (102mm) 3-7/16" (87mm) AM-341, AM-342 2" (51mm) AM-321, AM-332 Figure-2 Dimensions of Accessory Kits AM-321, AM-332, AM-341 and AM-342. 6 © Copyright 2008 TAC All Rights Reserved.
PAGE 8
Copyright 2008, TAC All brand names, trademarks and registered trademarks are the property of their respective owners. Information contained within this document is subject to change without notice. F-09240-11 TAC 1354 Clifford Avenue P.O. Box 2940 Loves Park, IL 61132-2940 www.tac.