User Guide

ManualsBrandsBarber Colman ManualsDampers150 lb-in DuraDrive Actuator (120V)

TAC

1354 Clifford Avenue

P. O. Box 2940

Loves Park, IL 61132-2940

www.tac.com

Application

TAC DuraDrive Direct Coupled Actuators are designed

to be used in both damper and valve control

applications. The follow general instructions are for

damper applications, refer to the Applicable Literature

table for valve literature.

The MA40-717X series actuators are over the shaft

spring return actuators used for two-position control

applications.

Features

• 150 lb-in (17 N-m) rated torque

• NEMA Type 4 housing (IEC IP56)

• Custom automatic current sensing motor control

provides extended reliability and repeatable timing

• Direct coupled to the damper shaft with dual

industrial hardened universal mounting clamps

• Two-position actuator controlled by SPST controller

• Clockwise or counterclockwise spring return is

determined by actuator mounting position

• Accurate 93° travel digitally controlled

• Integral position indication scale

• Rugged die-cast housing

• Oil immersed gear train provides continuous

lubrication

• Rated for operating temperature up to 140 °F

• Five year warranty

MA40-717X Series

TAC DuraDrive™

Series Spring Return

Two Position Actuators

General Instructions

†

† Refer to Table-1 to identify specific models that are

in conformance with CE standards.

Summary of content (16 pages)

PAGE 1
MA40-717X Series TAC 1354 Clifford Avenue P. O. Box 2940 Loves Park, IL 61132-2940 www.tac.com TAC DuraDrive™ Series Spring Return Two Position Actuators General Instructions Application TAC DuraDrive Direct Coupled Actuators are designed to be used in both damper and valve control applications. The follow general instructions are for damper applications, refer to the Applicable Literature table for valve literature.
PAGE 2
Applicable Literature F-Number Audience Purpose MX40-6XXX-2XX, MX40-7XXX-2XX Series Actuator/Linkage Assemblies General Instructions – – – – – Sales Personnel Application Engineers Installers Service Personnel Start-up Technicians Describes the globe valve actuator/linkage assembly’s features, specifications, and possible applications. Provides step-bystep mounting instructions.
PAGE 3
SPECIFICATIONS Inputs Control Signal: Two wire, SPST or Triacs. See Figure-1 through Figure-1. Power Input: See Table-1. All 24 Vac circuits are Class 2. All circuits 30 Vac and above are Class 1. Connections: Power, 24 inch (61 cm) long, 18 AWG color coded pigtail leads. Control, 24 inch (61 cm) long, 22 AWG color coded pigtail leads. Outputs Electrical: Stroke, Electronically limited to 93° ±1°. Torque See Table-1. Duty Cycle 100%. Timing See Table-1.
PAGE 4
Table-1 Model Chart. Actuator Power Input Part Number Voltage MA40-7173a 24 Vac ±20% MA40-7170 120 Vac ±10% MA40-7171a 240 Vac ±10% a Hz Watts 50 60 VA Running Holding 5.4 9.6 4.1 7.2 11.4 9.4 7.4 11.8 9.5 Approximate 93° Rotation Timing in Seconds @ 70° F (21° C) for Rated Torque Minimum Maximum Stall 145 150 (17) 450 (51) Output Torque Rating lb.-in. (N-m) This model is in conformance with CE standards.
PAGE 5
MA40-7173 1 24 Vac 3 Black 24H Black/Blue 24G Green/Yellow GRD 2 1 SPST or Triac Controller. Multiple MA40-7173 actuators may be powered by a single 24 Vac transofrmer. 2 Unused conduit port must remain plugged with a water tight pipe plug as shipped from factory to maintain NEMA Type 4 or IP56 rating. 3 Ground wire may be Green on some models. Figure-3 Typical MA40-7173 Wiring Diagram. INSTALLATION Inspection Requirements Inspect the package for damage.
PAGE 6
Precautions General Warning: • Electrical shock hazard! Disconnect the power supply (line power) before and during installation to prevent electric shock and equipment damage. • Make all connections in accordance with the wiring diagram and in accordance with national and local electrical codes. Use copper conductors only. Caution: • Avoid electrical noise interference. Do not install near large contactors, electrical machinery, or welding equipment.
PAGE 7
Mounting Mount the TAC DuraDrive Actuator directly on the damper shaft in locations that clear the maximum dimensions of the actuator case and allow the actuator to be mounted flush to the surface of the terminal box and perpendicular to the damper shaft. Note: Some terminal boxes have sheet metal screw heads or other protrusions near the damper shaft. In these cases, a spacer or shim may be added under the mounting tab of the actuator to make the actuator perpendicular to the shaft.
PAGE 8
Mounting the Actuator for Clockwise or Counterclockwise Spring Return The zero (0) position on the position indicator is the normal or spring return position. When the actuator is mounted with the “R” side facing the installer and the control signal increases the actuator will rotate in the counterclockwise direction. When the actuator is mounted with the “L” side facing the installer and the control signal increases the actuator will rotate in the clockwise direction. Long Damper Shaft 1.
PAGE 9
CENTERLINE 1 R 1 1 Two AM-754 Universal Mounting Clamp Assemblies are provided with each actuator. Each clamp assembly includes 1 universal mounting clamp and 1 retaining clip. Two Universal Mounting Clamp Assemblies are required for all mounting configurations. 5 Figure-5 Long Damper Shaft Mounting with Clockwise Spring Return for Normally Closed Damper. F-26742-2 © Copyright 2006 TAC All Rights Reserved.
PAGE 10
CENTERLINE 1 1 Two AM-754 Universal Mounting Clamp Assemblies are provided with each actuator. Each clamp assembly includes 1 universal mounting clamp and 1 retaining clip. Two Universal Mounting Clamp Assemblies are required for all mounting configurations. 5 Figure-6 Long Damper Shaft Mounting with Counterclockwise Spring Return for Normally Closed Damper. Actuator Mounting Slot AM-751 Anti-rotation Bracket 90 90 Figure-7 Mounting Anti-rotation Bracket to Actuator.
PAGE 11
Short Damper Shaft See Figure-8 for installation of actuator using the AM-676 Universal Shaft Extension. Installation requires AM-676 Universal Shaft Extension and AM-753 Universal Mounting Clamps for 3/4" to 1" (19 to 25 mm) shafts, these items must be ordered separately. 1. Loosen the V-clamp nuts on the AM-676 universal shaft extension. 2. Fit the universal shaft extension fully onto the damper shaft. Tighten the universal shaft extension V-clamp nuts with a 10 mm open-end wrench. Apply 4 to 6 ft-lbs.
PAGE 12
Actuator Anti-rotation Bracket (included with actuator) AM-753 Universal Mounting Clamp Assemblies 1 AM-676 Universal Shaft Extension Mounting Surface V-clamp Duct 1 The AM-676 extends the damper shaft approximately 9" (229 mm). Damper Shaft Figure-8 Installation of Universal Shaft Extension. Wiring Requirements Control and Power Leads Remove blue plastic thread protectors before installing conduit fittings.
PAGE 13
CHECKOUT This procedure is for checking out a normally closed actuator that is typically mounted unpowered. It is possible to mount the actuator with power applied for special applications. Note: To check out a normally open actuator the procedure is the same as below, except the initial position is open and the powered position is closed. After the entire system has been installed and the actuator has been powered up, the following check can be made for proper system operation.
PAGE 16
Copyright 2006, TAC All brand names, trademarks and registered trademarks are the property of their respective owners. Information contained within this document is subject to change without notice. TAC 1354 Clifford Avenue P.O. Box 2940 Loves Park, IL 61132-2940 F-26742-2 www.tac.