BARCO PROJECTION SYSTEMS CINE 6 R9002372 INSTALLATION MANUAL Date : 21112002 Rev : 05 Art. No.
Federal communication commission (FCC statement) This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules and EN55022. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Table of Contents i TABLE OF CONTENTS SAFETY INSTRUCTIONS .......................................................................................................................................................... 1-1 On safety ............................................................................................................................................................................. 1-2 On installation ........................................................................................
Safety Instructions 1 SAFETY INSTRUCTIONS Notice on Safety This equipment is built in accordance with the requirements of the international safety standards EN60950, UL 1950 and CSA C22.2 No.950, which are the safety standards of information technology equipment including electrical business equipment.
Safety Instructions On safety 1. This product should be operated from an AC power source. This projector may be connected to an IT-power system. Operating AC power voltage of the projector: BARCO CINE 6 : Art. No. R9002372 (With Limopro + PFC 85Vac to 250Vac) 2. This product is equipped with a 3-wire grounding plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature.
Safety Instructions On servicing Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage potential and risk of electric shock! Refer all servicing to qualified service personnel. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions : a. b. c. d. e. f. When the power cord or plug is damaged or frayed. If liquid has been spilled into the equipment.
Unpacking and Dimensions 2 UNPACKING AND DIMENSIONS Unpacking To open the banding, pull on the clip as shown in the first drawing. Take the projector out of its shipping carton and place it on a table. Save the original shipping carton and packing material, they will come in handy if you ever have to ship your projector. For maximum protection, repack your projector as it was originally packed at the factory. Contents of the shipped box : - 1 BARCO CINE 6 1 remote control + batteries (2 x 1.
Unpacking and Dimensions Projector Dimensions 2-2 ___________________________________________________________________________ R5975819.
Installation Guidelines 3 INSTALLATION GUIDELINES Installation guidelines Ambient Temperature Conditions Careful consideration of things such as image size, ambient light level, projector placement and type of screen to use are critical to the optimum use of the projection system. Max. ambient temperature : 40 0C (104 0F) Min.
Installation Guidelines Where to install the projector? To indicate a correct installation position it is necessary to know the distance : - projector - ceiling - projector - screen To find this correct position for the projector, equipped with HD 215 lenses, follow the instructions as on the screen : The projector - screen distance (PD), or the screen width (SW), can also be determined from the programme given in the screen by entering the screen width (SW) or prjector distance (PD) through the RCU.
Installation Guidelines Mounting the Ceiling Mount Washer M8 Screw M8 Screw M5 U plate Nut M5 Screw M4 Right L plate Left L plate Make the position on the ceiling. the U plate into the ceiling. Insert 2 screws with wesher M8 and tighten the screw lightly on both side of U plate. Fix the right and left L plate on the bottom of the projector, using two M4 screws each. Fix Shown in Fig. Lift the projector and hook on the 2 screws M8 of the U plate mounted on the ceiling.
Installation Set Up 4 INSTALLATION SET UP Access to Controls Opening procedure During the projector set up and installation it is necessary to remove the side and top covers. First remove the top cover, covering the lenses : • Turn both lock screws counter clockwise until they are raised by the springs. • Lift up the cover and remove. To remove the second top cover, covering the electronics, first the side covers have to be removed.
Installation Set Up Scan adaptation The scanning can be switched by turning the Horizontal and Vertical scan connectors. To change the scanning, it is necessary to open the projector top cover (see "Access To gain access to the connectors, the top frame has to be turned 90° to the back until Therefore, the following the next procedure : • Remove the four screws, two on each side, that are fixing the heatsinks to the • Remove three screws that are fixing the frame to the metal chassis.
Installation Set Up After scan inversion, close the chassis, re-install the second top cover, the side covers and the lens top cover. To install the side covers : • • • Hook the side cover on the both notches and Secure on with the three black screws on the bottom side. Reconnect the power cord to the wall outlet. Note : Switching over from floor to ceiling or vice versa requires a complete readjustment of picture geometry and convergence.
Installation Set Up Follow next procedure to check the configuration : - switch on the projector. the projector starts up on the last selected source. press the ADJUST key. highlight 'SERVICE' with the control disc and press ENTER. The 'SERVICE MODE' will be displayed select with the control disc 'PROJECTOR SET UP' and press ENTER. The 'PROJECTOR SET UP' will be displayed. Select with the control disc 'IDENTIFICATION' and press ENTER.
Projector Set Up 5 PROJECTOR SET UP Projector Set Up The software takes care of the set up of the projector. • • • • Projector address Power up Baud rate (9600) Password (strap is provided to disable) Password mode With strap J5 on the controller unit, the important projector adjustments can be protected with a password. When the password feature is enabled (strap mounted), the customer has to enter a password before he can enter the specific adjustment.
Projector Set Up Setting the projector address The projector's address may be set to any value between 0 and 255. When the address is set, the projector can be controlled now by RCU for addresses between 0 and 9. Note : A projector will respond to a RCU set to an address of 0 regardless of what address is set in the projector itself. Address setting is a software setup of your projector which must be done during installation.
Power Connection 6 POWER CONNECTION Power (mains) cord connection Use the supplied power cord to connect your projector to the wall outlet. at the front of the projector. Plug the female power connector into the male connector 120 / 230 V 4 A / 2.5 A 60 / 50 Hz 300 W Stand By / Operational Pause Sync Hold Down EHT IR Input power (mains) voltage adaptation Attention The BARCO CINE 6 - R9002372 leaves the factory with a PFC module to operate on a mains (power) input from 110Vac to 230Vac.
Installation Adjustments 7 INSTALLATION ADJUSTMENTS Entering the adjustment mode MAIN MENU Image Control Function Keys Press ADJUST to enter the adjustment mode. Service Menus Select with or then to return. WARNING RISK OF INCORRECT ADJUSTMENT OF THE PROJECTOR. The following service menus are reserved to, and to be performed only by qualified personnel ! If qualified, press to continue, or if not, to return.
Installation Adjustments Installation mode start up It will be necessary to perform several mechanical adjustments while in the installation mode. gain access to the adjustment points (see Access to Controls). Two possible ways to enter the installation mode : Remove the top cover in order to a) Using the RCU. Press the ADJUST key. The projector displays the path selection menu. MAIN MENU WARNING RISK OF INCORRECT ADJUSTMENT OF THE PROJECTOR.
Installation Adjustments Note : When the password mode is active, your password will be asked. Your password contains 4 digits. a) Adjusting the projector password with the RCU. Enter the digits with the numeric keys on the RCU. Example : 2 3 1 9 For each digit entered, a 'X' appears on the screen under the displayed text 'enter password'. When your password is correct, you get access to the 'ADJUSTMENT MODE'. When the entered password is wrong, The message 'WRONG PASSWORD !!!' will be displayed.
Installation Adjustments Optical lens focusing The optical focusing procedure is performed separately for each lens. proceeds through the optical focusing adjustment sequence. The appropriate CRT will be switched on as the user Each lens has one focus adjustment point. The projected image is focused by loosening the wing nut of the lens and rotating the lens barrel until the image is clearly focused. Press ENTER key to continue. ENTER continues to Raster centering. EXIT exit from installation menu.
Installation Adjustments Raster centering The raster must be centered on the CRT screen surface of each tube, therefore, it is necessary to look into the lenses. WARNING : In order to ensure maximum CRT longevity and to avoid CRT damage, do not shift the raster outside the phosphor area of the CRT. Press ENTER to display the raster on the green CRT. Look into the green lens and shift the raster with the control keys it is centered in the middle of the CRT faceplate.
Installation Adjustments CRT projection angle adjustment The projection angle of the red and blue CRT's is dependent on the desired size of the projected image. If the centers of green, blue and red do not coincide, the CRT projection angle must be adjusted. Never try to correct this misalignment with the shift correction or the static convergence controls. These controls may only be applied to correct small errors which cannot be corrected by the CRT angle adjustment.
Installation Adjustments D C Screws A, B, C and D (M4) : upper fixation latch. nutdriver 7mm. Screw A', B', C' and D' (M4) : lower fixation latch. nutdriver 7mm. B A Loosen the two hexagon screws A and A' upper and lower fixation tube. Pivot the red CRT until the center of the red image coincides pivot, loosen also screw B a little bit. If the angle of the red CRT ENTER continues to blue and green crosshairs. EXIT will return to CRT projection angle adjustment.
Installation Adjustments alignment procedure for the projector. You have the choice between: - guided Adjustment Procedure - random Access Adjustment Procedure The result of both procedures will be the same. More explanation about both procedures is given in the owners manual. The following paragraph gives an overview of the image corrections. Alignment of the projector Overview of the corrections For detailed information about these corrections and procedures to be followed, see owner's manual.
G2 Adjustment A G2 ADJUSTMENT G2 adjustment Enter the adjustment mode by pressing ADJUST and highlight SERVICE. Highlight 'common settings' and press ENTER. ENTER starts up the common settings menu. EXIT returns to the adjustment mode menu. Highlight G2 adjust and press ENTER. A safety notice will be displayed to warn the operator. Press ENTER to start up the service mode. If you are qualified, press ENTER to continue with the G2 adjustment, otherwise press EXIT to return to the service menu.