Coronis Fusion 10MP User Guide
(This page intentionally left blank.
Welcome! Thank you for choosing this CORONIS FUSION 10MP display! Equipped with proprietary 'SmoothGray' technology for a meticulously rendered grayscale curve, the CORONIS FUSION 10MP display makes subtle details and lesions more noticeable than ever before. Add to this exceptionally high brightness and contrast levels, truly dark blacks and perfect geometry and you begin to understand that supreme grayscale precision has a new meaning.
(This page intentionally left blank.
Table of contents What's in the box.............................................................7 Parts, controls and connectors ........................................9 Front view ............................................................................................... 9 Rear view .............................................................................................. 10 Display installation ........................................................11 Removing the covers .......................
DPMS mode........................................................................................... 30 Luminance target.................................................................................. 31 Viewing modes ..................................................................................... 31 Display functions................................................................................... 32 Ambient Light Compensation (ALC)....................................................
What's in the box Your CORONIS FUSION 10MP display comes with: • this CORONIS FUSION 10MP display guide • a system CD • two DVI cables • two DisplayPort cables • a USB cable • a set of AC power cords • an external power supply If you ordered a Barco display controller, it’s also in the box together with its accessories and dedicated user guide. Keep your original packaging. It is designed for this display and is the ideal protection during transport.
(This page intentionally left blank.
Parts, controls and connectors Front view 1 2 3 4 5 6 7 8 1 USB downstream connectors 2 Left/Up key 3 Right/Down key 4 Menu/Enter key 5 Stand-by/Cancel key 6 Ambient light sensor 7 Power status indicator light 8 Control wheel Coronis Fusion 10MP 9
Rear view 1 2 3 4 5 6 7 8 9 10 11 12 1 USB downstream connector 2 USB upstream connector 3 Ethernet connector (see note below) 4 DVI 1 video input 5 DisplayPort 1 video input 6 Connector compartment cover 7 Neck cover 8 Display stand cover 9 DisplayPort 2 video input 10 DVI 2 video input 11 +5 VDC, 0.5 A power output 12 +24 VDC power input The Ethernet connection is used for maintenance purposes and is not supported for user application.
Display installation Prior to installing your CORONIS FUSION 10MP display and connecting all necessary cables, make sure to have a suitable display controller physically installed in your computer. If you are using a Barco display controller, please consult the user guide delivered with it to do this. Removing the covers CONNECTOR COMPARTMENT COVER The connector compartment cover should be removed to get access to the connectors.
DISPLAY STAND COVER To get access to the cable routing channel, the display stand cover should be removed. This can be done as follows: 1 Gently press and hold the clips at the inside top of the cover. 2 Slide the cover upwards while holding the clips pressed.
Unlocking the height mechanism In the factory, the height-positioning system in the display stand is locked with a red hook to prevent damage during transportation. You’ll have to remove this hook before adjusting your display height position. 1 While holding the display panel pushed down, pull out the red hook in the display stand. To retain the hook for possible future transportation, insert the short, red end of the hook back into the stand of your display.
Adjusting the display position Now that the height-positioning system of your display is unlocked, you can tilt, swivel, raise and lower the display as desired. Do not try to pivot your display when attached to the stand. Trying to do so could cause serious damage to your display and its stand.
Connecting the signal cables 1 Connect one head of the display controller to the DVI 1 or DisplayPort 1 connector with one of the supplied DVI or DisplayPort cables. 2 Connect another head of the display controller to the DVI 2 or DisplayPort 2 connector with one of the supplied DVI or DisplayPort cables. Each side of your display can have a different video input connected (one side can have DVI connected while the other side has DisplayPort connected).
Connecting the power cables 1 Connect the supplied external DC power supply to the +24 VDC power input of your CORONIS FUSION 10MP display. 2 Plug the other end of the external DC power supply into a grounded power outlet by means of the proper power cord delivered in the packaging. Routing the cables Route all connected cables trough the cable routing channel in the stand of your display.
Re-attaching the covers 1 Re-attach the display stand cover by sliding it downward. You’ll hear a “click” sound of the cover’s clips when the display stand cover is in position. Pay attention that all cables stay in the cable channel while replacing the cover. 2 Re-attach the connector compartment cover by sliding the cover’s top in position and then push the cover’s bottom. You’ll hear a “click” sound of the cover’s clips when the connector compartment cover is in position.
VESA-mount installation The panel, standard attached to a stand, is compatible with the VESA 100 mm standard. Thus, it can be used with an arm that is approved by VESA. This chapter shows you how to release the panel from the stand and how to attach it to an arm. If you’re not using an arm, you can skip this chapter. 1 Gently pull open both lower sides of the cover. 2 Slide the cover upwards while holding the lower sides pulled open.
3 Lift the plastic frame that covers the fixation of the panel to the stand. Turn it for 45 degrees to uncover the fixation screws. 4 Unscrew the four fixation screws fixing the panel to the stand. 5 Attach the panel firmly to the arm using 4 screws M4 x 10 mm. You should mount the panel in landscape position. Portrait position is not supported. Use an arm that can support a weight of at least 18 kg (39.68 lbs).
First time starting up You are now ready to start up your CORONIS FUSION 10MP display system for the first time. 1 Switch on your CORONIS FUSION 10MP display as described in “Stand-by switching” on page 24. 2 Turn on the computer connected to your display. If you have properly installed your display and display controller, the Windows start-up messages will appear once the boot procedure is finished.
Daily operation Recommendations for daily operation OPTIMIZE THE LIFETIME OF YOUR DISPLAY Enabling the Display Power Management System (DPMS) of your display will optimize its diagnostic lifetime by automatically switching off the backlight when the display is not used for a specified period of time. By default, DPMS is enabled on your display, but it also needs to be activated on your workstation. To do this, go to “Power Options Properties” in the “Control Panel”.
performance of the product. To ensure optimal product quality, Barco applies strict selection criteria for its LCD panels. To learn more about LCD technology and missing pixels, consult the dedicated white papers available at www.barco.com/ medical. ENHANCE USER COMFORT Every Barco multi-head display system is color matched with the highest specification in the market. Barco recommends keeping color-matched displays together.
Keys indicator lights By default, the keys indicator lights will be dimmed which makes them unavailable at that moment. TO MAKE THE KEYS LIGHT UP: 1 Gently sweep your finger over the bottom right hand side of your display. As a result, the keys will light up and are now available for further actions. However, if no further actions are taken within the following 5 seconds, the keys indicator lights will dim again. The keys indicator lights auto-dim function can be disabled in the OSD menu.
Stand-by switching Switching on the display while it is in stand-by mode or vice versa can both be done by using the keys or by using the control wheel. TO SWITCH YOUR DISPLAY ON/STAND-BY USING THE KEYS: 1 Light up the keys indicator lights as previously described. 2 While the keys are light up, touch the Stand-by/Cancel approximately 2 seconds. key for TO SWITCH YOUR DISPLAY ON/STAND-BY USING THE CONTROL WHEEL: 1 Press and hold the control wheel for approximately 2 seconds.
Bringing up the OSD menu The OSD menu allows you to configure different settings to make your CORONIS FUSION 10MP display fit your needs within your working environment. Also, you can retrieve general information about your display and its current configuration settings through the OSD menu. TO BRING UP THE OSD MENU USING THE KEYS: 1 If not already done so, switch on the display as previously described. 2 Light up the keys indicator lights as previously described.
Navigating through the OSD menus ABOUT OSD MENU NAVIGATION Navigating through the OSD menu can be done by using the keys or by using the control wheel. TO NAVIGATE THE OSD MENU USING THE KEYS: • Use the Right/Down and Left/Up keys to move through the (sub)menus, change values or make selections. • To go into a submenu or confirm adjustments and selections, use the Menu/Enter key. • Use the Stand-by/Cancel (sub)menu.
Advanced operation OSD menu position ABOUT THE OSD MENU POSITION By default, the OSD menu comes up in the bottom right corner of the screen. This position can be modified however. There’s choice from a number of predefined positions. TO CHANGE THE POSITION OF THE OSD MENU: 1 Bring up the OSD main menu. 2 Navigate to the Configuration > User Interface > Menu menu. 3 Enter the Position submenu. 4 Select one of the available OSD menu positions and confirm.
OSD menu automatic close function ABOUT THE OSD MENU AUTOMATIC CLOSE FUNCTION By default, the OSD menu will disappear automatically after approximately 90 seconds of inactivity. However, this function can be disabled so that the OSD menu remains on the screen until manually closed. TO ENABLE/DISABLE THE OSD MENU AUTOMATIC CLOSE FUNCTION: 1 Bring up the OSD main menu. 2 Navigate to the Configuration > User Interface > Menu menu. 3 Enter the Automatic Close submenu.
Keys indicator lights ABOUT THE KEYS INDICATOR LIGHTS By default, after lighting up, the keys indicator lights will dim again if no further actions are taken within the following 5 seconds. However, this behavior can be changed so that the keys indicator lights are always on or always off. TO CONFIGURE THE KEYS INDICATOR LIGHTS: 1 Bring up the OSD main menu. 2 Navigate to the Configuration > User Interface > Indicator Lights menu. 3 Enter the Keys submenu.
Keys sound ABOUT THE KEYS SOUND By default, the keys will make a “beep” sound on every touch. However, this sound can be disabled so that no sound will be heard when using the keys. TO ENABLE/DISABLE THE KEYS SOUND: 1 Bring up the OSD main menu. 2 Navigate to the Configuration > User Interface > Controls menu. 3 Enter the Sound submenu. 4 Select Enabled/Disabled as desired and confirm.
Luminance target ABOUT THE LUMINANCE TARGET The luminance target of your CORONIS FUSION 10MP display is adjustable over a predefined range. When you change the luminance target, the display will adjust its backlight to reach the target. TO SET THE LUMINANCE TARGET: 1 Bring up the OSD main menu. 2 Navigate to the Configuration > Calibration menu. 3 Enter the Luminance Target submenu. 4 Set a luminance target value as desired and confirm.
Display functions ABOUT DISPLAY FUNCTIONS Native, uncorrected panels will display all grayscale/color levels at an equal luminance. Studies have shown however, that in medical images certain grayscale/color parts contain more diagnostic information then others. To respond to these conclusions, display functions have been defined. These functions emphasize on these parts containing crucial diagnostic information by correcting the native panel behavior.
TO SELECT A DISPLAY FUNCTION: 1 Bring up the OSD main menu. 2 Navigate to the Configuration > Calibration menu. 3 Enter the Display Function submenu. 4 Select one of the available display functions and confirm. Ambient Light Compensation (ALC) ABOUT ALC Ambient Light Compensation (ALC) can only be enabled on your display when the DICOM display function is selected. Therefore, please refer to “Display functions” on page 32 to correctly set the display function.
Reading rooms ABOUT READING ROOMS Reading rooms can only be selected when the DICOM display function is selected. Therefore, please refer to “Display functions” on page 32 to correctly set the display function. The American Association of Physicists in Medicine (AAPM) composed a list of pre-defined reading rooms.
Emergency Room Corresponds to light conditions in emergency rooms. Operating Room Corresponds to light conditions in operating rooms. This setting has the highest maximum ambient light. TO SELECT A READING ROOM: 1 Bring up the OSD main menu. 2 Navigate to the Configuration > Calibration > Ambient Light menu. 3 Enter the Reading Room submenu. 4 Select one of the available reading rooms and confirm.
Image scaling ABOUT IMAGE SCALING Enabling image scaling will multiply each individual pixel to one or more adjacent pixels so that the size of the displayed image will be a multiple of the original image source video input signal. Image scaling is only possible when the resolution of your display’s video input signal is less than or equal to half the maximum resolution of the display. TO ENABLE/DISABLE IMAGE SCALING: 1 Bring up the OSD main menu. 2 Navigate to the Configuration > Image Sources menu.
adjust certain video settings yourself. The start to this is selecting one of the following image source selection modes available for your display: Automatic In this mode, your display automatically detects the connected video input signals, attaches them to the correct display side and applies the correct video settings to it (resolution, video encoding mode, refresh rate,...). No video settings are available when this mode is selected.
Video input signals ABOUT VIDEO INPUT SIGNALS Your CORONIS FUSION 10MP display automatically detects the connected video input signals. Manually selecting image source video input signals is possible, but then your display’s image source selection mode should be set to allow this. Please refer to “Image source selection modes” on page 36 to do this.
Video encoding modes ABOUT VIDEO ENCODING MODES Your CORONIS FUSION 10MP display automatically detects the connected video input signals and applies the correct video encoding settings. Manually selecting a video encoding mode is possible, but then your display’s image source selection mode should be set to allow this. Please refer to “Image source selection modes” on page 36 to do this. Video encoding modes specify how the color and luminance information is encoded in the video signal.
Dual 10 Dual 10 is a Barco specific 10-bit video encoding mode which is usually used on grayscale displays and which allows full refresh rate. Automatic When selecting this option, your CORONIS FUSION 10MP display will automatically assign the correct video encoding settings to the connected video input signals. TO MANUALLY SELECT A VIDEO ENCODING MODE: 1 Bring up the OSD main menu. 2 Navigate to the Configuration > Image Sources > (Left/Right) Image Source menu. 3 Enter the Video Encoding submenu.
Use Green Channel This mode is intended for grayscale displays where gray is sent over the green channel. Use Blue Channel This mode is intended for grayscale displays where gray is sent over the blue channel. Use All Channels This mode is intended for grayscale displays where gray is sent over the red, green and blue channel. This done by means of a standard conversion mechanism where 30% red, 59% green and 11% blue are used to generate gray.
Video timings ABOUT VIDEO TIMINGS Your CORONIS FUSION 10MP display automatically detects the connected video input signals and applies the correct timings. Manually configuring the video timings is possible, but then your display’s image source selection mode should be set to allow this. Please refer to “Image source selection modes” on page 36 to do this.
Display info ABOUT DISPLAY INFO Your display serial number, color type, native resolution, firmware versions, etc. are available in a dedicated submenu of the OSD menu. TO RETRIEVE INFO ABOUT YOUR DISPLAY: 1 Bring up the OSD main menu. 2 Navigate to the About this Display menu. 3 Enter the Display or Firmware submenu as desired. Display status ABOUT DISPLAY STATUS The Status submenu of the OSD menu provides info on the current status of your display (runtimes, temperatures, etc.
(This page intentionally left blank.
Cleaning your display Front glass Before cleaning the front glass, unplug the power cable from the mains to prevent the keys from being activated inadvertently by sweeping over them. Clean the front glass using a sponge, cleaning cloth or soft tissue, lightly moistened with one of the following tested products: • Flux • Windex Glass Plus • Bohle glass cleaner • Mr. Proper • Pril • Ajax glass cleaner • Sidolin glass cleaner In case none of the above cleaning products is available, use plain water.
Do not use following products: • Alcohol/solvents at higher concentration > 5% • Strong alkalis lye, strong solvents • Acid • Detergents with fluoride • Detergents with ammonia • Detergents with abrasives • Steel wool • Sponge with abrasives • Steel blades • Cloth with steel thread Cabinet 1 Clean the cabinet using a soft cotton cloth, lightly moistened with a recognized cleaning product for medical equipment.
Important information Safety information GENERAL RECOMMENDATIONS Read the safety and operating instructions before operating the display. Retain safety and operating instructions for future reference. Adhere to all warnings on the display and in the operating instructions manual. Follow all instructions for operation and use.
POWER CONNECTION - DISPLAY WITH EXTERNAL 24 VDC POWER SUPPLY • Power requirements: The display must be powered using the delivered medical approved 24 VDC SELV power supply. • The medical approved DC power supply must be powered by the AC mains voltage (protective earth terminal). POWER CORDS: • Utilize a UL-listed detachable power cord, 3-wire, type SJ or equivalent, 18 AWG min., rated 300 V min.
display may fall, causing serious injury to a child or adult, and serious damage to the equipment. THIS APPARATUS CONFORMS TO: CE0120 (MDD 93/42/EEC class IIb product), CE - 2004/108/EC, CE - 93/ 42/EEC; A1:2007/47/EC class II b, UL 60601-1 1ST EDITION, CAN/CSAC22.2 NO. 601.1-M90, IEC 60601-1 2ND ED:1988 + A1:1991 + A2:1995, IEC 60950-1:2005 2ND EDITION, DEMKO - EN 60601-1, CCC - GB92542008 + GB4943-2001 + GB17625.1-2003, VCCI, FCC class B, BSMI, FDA 510K, RoHS, KC NATIONAL SCANDINAVIAN DEVIATIONS FOR CL.
Environmental information DISPOSAL INFORMATION (WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT) This symbol on the product indicates that, under European Directive 2002/96/EC governing waste from electrical and electronic equipment, this product must not be disposed of with other municipal waste. Please dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment.
中国大陆 ROHS (CHINESE MAINLAND ROHS) 根据中国大陆 《电子信息产品污染控制管理办法》（也称为中国大 陆 RoHS），以下部分列出了 Barco 产品中可能包含的有毒和 / 或有 害物质的名称和含量。中国大陆 RoHS 指令包含在中国信息产业部 MCV 标准：“ 电子信息产品中有毒物质的限量要求 ” 中。 According to the "China Administration on Control of Pollution Caused by Electronic Information Products" (Also called RoHS of Chinese Mainland), the table below lists the names and contents of toxic and/or hazardous substances that Barco's product may contain.
电源供应器 X O O O O O O O O O O O O O O O O O Power supply unit 文件说明书 Paper manuals 光盘说明书 CD manual O: 表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限 量要求以下 . O: Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is below the limit requirement in SJ/T11363-2006. X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规 定的限量要求 .
Regulatory compliance information INDICATIONS FOR USE The CORONIS FUSION 10MP display (MDCG-10130) is intended to be used in displaying and viewing digital images, including digital mammography, for review and analysis by trained medical practitioners. Caution (USA): Federal law restricts this device to sale by or on the order of a physician or a practitioner trained on its use. FCC CLASS B This device complies with Part 15 of the FCC Rules.
Explanation of symbols On the display or power supply, you may find the following symbols (nonrestrictive list): 0120 Indicates compliance to the essential requirements of the Directive 93/42/EEC Indicates compliance with Part 15 of the FCC rules (Class A or Class B) Indicates the display is approved according to the UL regulations or or Indicates the display is approved according to the c-UL regulations Indicates the display is approved according to the DEMKO regulations S&E Indicates the display is
Consult the operating instructions Indicates this apparatus must not be thrown in the trash but must be recycled, according to the European WEEE (Waste Electrical and Electronic Equipment) directive Legal disclaimer Although every attempt has been made to achieve technical accuracy in this document, we assume no responsibility for errors that may be found. Our goal is to provide you with the most accurate and usable documentation possible; if you discover errors, please let us know.
Technical specifications Product acronym MDCG-10130 Screen technology TFT AM LCD Dual Domain IPS Active screen size 761 mm (29.6”) (diagonal) Active screen size (H x V) 645 x 403 mm (25.4 x 15.9“) Aspect ratio (H:V) 16:10 Resolution 10MP (4096 x 2560) Pixel pitch 0.
Scanning frequency (H; V) 30-150 kHz; 15-80 Hz Housing color Black/Silver Video input signals DVI-D Dual Link (2x) / DisplayPort (2x) Video inout terminals NA USB ports 1 upstream (endpoint), 3 downstream USB standard 2.
Tilt -5° / +25° Swivel -30° / +30° Pivot NA Mounting standard VESA (100 mm) Screen protection Protective, non-reflective glass cover Recommended modalities CT, MR, US, DR, CR, NM, Film Certifications CE0120 (MDD 93/42/EEC class IIb product), CE 2004/108/EC, CE - 93/42/EEC; A1:2007/47/EC class II b, UL 60601-1 1ST EDITION, CAN/CSA-C22.2 NO. 601.
Warranty statement BARCO MID GENERAL WARRANTY TERMS AND CONDITIONS Applicable from Jan 1st 2008 ARTICLE 1: PRODUCT WARRANTY Barco nv, Medical Imaging Division warrants that the equipment will be free of defects in workmanship or material for the warranty period or the specific period of a warranty extension program.
B. Products have not been installed by Barco or its authorized subcontractors); (iv)not been subject to any unauthorized access, alteration, modification or repair or attempts thereto; (v) been at all times "normally used" for the intended purpose and operated in strict accordance with the operating instructions set forth in the operating manual of the Product in question and shall not have been otherwise misused, abused, damaged.
iii. difference in color temperature that is lower than the total allowable difference as mentioned in the product specifications iv. difference in color temperature as a result of not using all displays of a multi-head configuration at the same rate. v. LCD luminance uniformity that is in within the product specifications or luminance uniformity performance that is inherent to LCD technology. Barco nv, MID does not warrant a minimum life time nor a performance of any of the consumables. 2.
expression "force majeure" means, but shall not be limited to, industrial dispute, fire, mobilisation, requisition, embargo, currency transfer prohibitions, insurrection, lack of means of transport, restrictions of the use of energy, and generally any circumstances which are beyond the control of the parties and hinder performance by one party of his obligations. ARTICLE 8: GENERAL 8.
work, and a "work based on the Program" means either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or with modifications and/or translated into another language. (Hereinafter, translation is included without limitation in the term "modification".) Each licensee is addressed as "you". Activities other than copying, distribution and modification are not covered by this License; they are outside its scope.
have their licenses terminated so long as such parties remain in full compliance. 5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License.
Copyright (C) 2007 Free Software Foundation, Inc. Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. Preamble The GNU General Public License is a free, copyleft license for software and other kinds of works. The licenses for most software and other practical works are designed to take away your freedom to share and change the works.
The "source code" for a work means the preferred form of the work for making modifications to it. "Object code" means any non-source form of a work. A "Standard Interface" means an interface that either is an official standard defined by a recognized standards body, or, in the case of interfaces specified for a particular programming language, one that is widely used among developers working in that language.
d) If the work has interactive user interfaces, each must display Appropriate Legal Notices; however, if the Program has interactive interfaces that do not display Appropriate Legal Notices, your work need not make them do so.
included in this License, to the extent that they are valid under applicable law. If additional permissions apply only to part of the Program, that part may be used separately under those permissions, but the entire Program remains governed by this License without regard to the additional permissions. When you convey a copy of a covered work, you may at your option remove any additional permissions from that copy, or from any part of it.
you may not initiate litigation (including a cross-claim or counterclaim in a lawsuit) alleging that any patent claim is infringed by making, using, selling, offering for sale, or importing the Program or any portion of it. 11. Patents. A "contributor" is a copyright holder who authorizes use under this License of the Program or a work on which the Program is based. The work thus licensed is called the contributor's "contributor version".
If the Program specifies that a proxy can decide which future versions of the GNU General Public License can be used, that proxy's public statement of acceptance of a version permanently authorizes you to choose that version for the Program. Later license versions may give you additional or different permissions. However, no additional obligations are imposed on any author or copyright holder as a result of your choosing to follow a later version. 15. Disclaimer of Warranty.
Therefore, we insist that any patent license obtained for a version of the library must be consistent with the full freedom of use specified in this license. Most GNU software, including some libraries, is covered by the ordinary GNU General Public License. This license, the GNU Lesser General Public License, applies to certain designated libraries, and is quite different from the ordinary General Public License.
program that uses the facility, other than as an argument passed when the facility is invoked, then you must make a good faith effort to ensure that, in the event an application does not supply such function or table, the facility still operates, and performs whatever part of its purpose remains meaningful. (For example, a function in a library to compute square roots has a purpose that is entirely well-defined independent of the application.
of definitions files in the Library will not necessarily be able to recompile the application to use the modified definitions.) b) Use a suitable shared library mechanism for linking with the Library.
excluded. In such case, this License incorporates the limitation as if written in the body of this License. 13. The Free Software Foundation may publish revised and/or new versions of the Lesser General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number.
3. b) under the GNU GPL, with none of the additional permissions of this License applicable to that copy. Object Code Incorporating Material from Library Header Files. The object code form of an Application may incorporate material from a header file that is part of the Library.
Coronis Fusion 10MP
Coronis Fusion 10MP 77
Coronis Fusion 10MP
Coronis Fusion 10MP 79
K5902031-00 May 2011 0120 Barco n.v. President Kennedypark 35 8500 Kortrijk Belgium www.barco.
