Coronis Fusion 6MP Getting Started Guide
(This page intentionally left blank.
Copyright notice Copyright This document is copyrighted. All rights are reserved. Neither this document, nor any part of it, may be reproduced or copied in any form or by any means - graphical, electronic, or mechanical including photocopying, taping or information storage and retrieval systems without written permission of Barco. © 2011 Barco N.V. All rights reserved.
pixel pitch of 0.1995mm. This provides the equivalent resolution of 2 x 3MP displays. The Coronis Fusion 6MP DL (MDCC-6130) display is not intended for primary diagnostic review of Mammography images.
Table of Contents Table of Contents Preface..................................................................................... 7 FCC compliance information ............................................................ 8 FCC statement for the display .................................................. 8 CE mark notice ................................................................................. 9 Environmental information ...........................................................
Table of Contents Driver and software installation prerequisites...................... 50 Installing the BARCO MXRT drivers and software ................... 50 Where to get more information............................................ 57 Troubleshooting..................................................................... 61 General tips .................................................................................... 62 Configuring Windows..................................................................
Preface Preface 7
FCC compliance information FCC compliance information FCC statement for the display Class B: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
CE mark notice CE mark notice Declaration of Conformity in accordance with Article 10 (1) of the CE directive This product has been designed and manufactured in accordance with the essential requirements of the Directives 89/336/EEC and MDD 93/42/EEC (class II b product), and for this product the procedures of Annex II have been applied to mark the product with the CE label.
Environmental information Environmental information Disposal Information This product consists of devices that may contain mercury, which must be recycled or disposed of in accordance with local, state, or country laws. (Within this system, the backlight lamps in the monitor display contain mercury.) This equipment has required the extraction and use of natural resources for its production. It may contain hazardous substances for health and environment.
Environmental information Information for China ROHS compliance Table of toxic and hazardous substances/elements and their content, as required by China’s management methods for controlling pollution by electronic information products Toxic or hazardous Substances and Elements Part Name Pb Hg Cd Cr6+ PBB PBDE Metal parts O O O O O O Plastic parts O O O O O O PCB or PCBA O O O O O O LCD panel X X O O O O Power supply/adapter X O O O O O Power cable X O O O O O
Environmental information LCD Monitor 零部件名稱 有毒有害物質或元素 铅 汞 镉 （Pb） （Hg） （Cd） 金属机构件 O O O 塑料机构件 O O O O O O 电路板组件 * 液晶面板 X X O 电源模块 / 适配器 X O O 电源线 X O O 外部信号连接线 O O O 六价铬 （Cr6+） O O O O O O O 多溴联苯 多溴二苯醚 （PBB） （PBDE） O O O O O O O O O O O O O O *： 电路板组件包括印刷电路板及其构成的零部件，如电阻、电容、集成电路 、连接器等 ○：表示该有毒有害物质在该部件所有均质材料中的含量均在 《电子信息产品中有 毒有害物质的限量要求标准》规定的限量要求以下 ×：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 《电子信息产品中 有毒有害物质的限量要求标准》规定的限量要求； 但是上表中打 “×” 的部件，其含量超出是因为目前业界还没有成熟的可替代的技术 12
Safety Instructions Safety Instructions General Recommendations Read the safety and operating instructions before operating the display. Retain safety and operating instructions for future reference. Adhere to all warnings on the display and in the operating instructions manual. Follow all instructions for operation and use.
Safety Instructions • The medical approved DC power supply must be powered by the AC mains voltage. Power cords: • Utilize a UL-listed detachable power cord, 3-wire, type SJ or equivalent, 18 AWG min., rated 300 V min., provided with a hospital-grade type plug 5-15P configuration for 120V application, or 6-15P for 240V application. • Do not overload wall outlets and extension cords as this may result in fire or electric shock. • Mains lead protection (U.S.
Safety Instructions This apparatus conforms to: CE0120 (MDD 93/42/EEC class IIb product), IEC 60601-1, UL 60601-1, CAN/CSA C22.2 No. 601.01-M90 (c-UL), CCC GB4943-1995 (IEC 60950-1). National Scandinavian Deviations for Cl. 1.7.
Explanation of symbols Explanation of symbols Symbols on the display and / or power supply On the display or power supply, you may find the following symbols (nonrestrictive list): Indicates compliance to the essential requirements of the Directive 93/42/EEC Indicates compliance with Part 15 of the FCC rules (Class A or Class B) Indicates the display is approved according to the UL regulations or or Indicates the display is approved according to the c-UL regulations Indicates the display is approved acc
Explanation of symbols Indicates the display serial no.
Recommendations for using your display system Recommendations for using your display system 1. Optimize the lifetime of your display Enabling the Display Power Management System (DPMS) of your display (in the display’s Settings menu) will optimize its diagnostic lifetime by automatically switching off the backlight when the display is not used for a specified period of time. By default, DPMS is enabled on your display, but it also needs to be activated on your workstation.
Recommendations for using your display system diagnostic performance of the product. To ensure optimal product quality, Barco applies strict selection criteria for its LCD panels. To learn more about LCD technology and missing pixels, consult the dedicated white paper available at www.barcomedical.com. 4. Enhance user comfort Every Barco multi-head display system is color matched with the highest specification in the market. Barco recommends keeping color-matched displays together.
Recommendations for using your display system (This page intentionally left blank.
Display controller installation Display controller installation 21
Display Controller Installation Display Controller Installation Which display controller? Your Barco medical display is compatible with a large range of Barco and non-Barco display controller boards. Depending on the customer’s order details, the display can be delivered with or without a display controller. The brochure “Barco medical display systems” on the website www.barco.
Display Controller Installation Types of display controllers for Barco Display Systems The following models of Barco display controllers are available for your display system.
Display Controller Installation Installation Procedure The following instructions will take you step by step through the installation of the Barco display controller(s) for your BARCO CORONIS FUSION 6MP Display System. CAUTION – Wear a grounded, protective ESD strap when handling or during installation of the display controller. Electrostatic charges can damage the display controller. 1.
Display Controller Installation 7. Align the Barco display controller(s) for your BARCO CORONIS FUSION 6MP Display System with the slot(s) and press it(them) in firmly until the card(s) is(are) fully seated. Note: The next step applies only to the MXRT 7300. 8. Connect the power cable to the 6-pin power connection on the graphics card. Make sure the cables are not interfering with anything inside the computer (for example, a cooling fan).
Display Controller Installation Connecting your Barco displays For a detailed description of the display installation and signal connection, please refer to the “Display installation” section of this manual. MXRT 1150 & MXRT 2150 IO-Panel for the Barco MXRT 1150 and Barco MXRT 2150 X S-Video Connection This option is not supported by Barco. Y DMS-59 connector provides DVI-I / Head 1 & Head 2 output connections through included Y adaptor cable.
Display Controller Installation MXRT 7300 IO-Panel for the Barco MXRT 7300 X DisplayPort Connections Y DVI-I Connection Note: Disconnecting the DisplayPort cable may lock the display. Rebooting system may be required if lock occurs. Note: Only two of the three connectors can be used at a time. Driving three displays is not supported with the MXRT 7300.
Display Controller Installation DualLink Dongle - for color 3mp or higher (ex: MDCC-6130). Must be ordered separately, part number B560602. Firmware v1.07 or higher required. 11. Reconnect any cables you have disconnected and plug in the computer’s power cord. 12. Turn on the display(s) and then your computer. Turning on your system WARNING - Turn on your display(s) before you turn on your computer. Failure to do so could damage your display(s).
Display Controller Installation 13. Install the drivers, MediCal QAWeb software and documentation for your Barco Coronis Fusion 6MP Display System by following the instructions in the Driver and Software Installation section of this manual.
Display Controller Installation (This page intentionally left blank.
Display installation Display installation 31
Installation precautions Installation precautions Precautions • Keep your original packaging. It is designed for this display and is the ideal protection during transport. • Avoid reflections in the flat panel to reduce eye strain. • Make sure the surface, stand, arm or boom to bear the display is strong and stable enough to bear its weight. • Keep the display away from heat sources and provide enough ventilation around the display. • Do not use the display in direct sunlight.
Display parts, controls and connectors Display parts, controls and connectors LED indicator The LED color indicates the display’s power status: Table 1: Green Display is on (when enabled in the OSD). Orange Display is in Standby power-saving mode. Off Display is disconnected from the power or the LED’s on state is disabled in the OSD. Note: When the LED is disabled in the OSD, it will still be activated (green) when the display is on but does not receive any video signal.
Display parts, controls and connectors 1 2 3 4 5 Figure 1: Touch keys 1. Left/Down touch key To move down or decrease values in the OSD. 2. Right/Up touch key To move up or increase values in the OSD. 3. Enter touch key To display the OSD (on-screen display). In the OSD, this button acts as Enter button to make selections. 4. Standby touch key To put the display in standby mode. 5.
Display parts, controls and connectors Control wheel The control wheel can be pressed like a push button and rotated like a knob. It allows to put the display in stand-by, navigate through the onscreen display (OSD) menus and change values in the OSD. The control wheel is located at the bottom of the LCD panel.
Display parts, controls and connectors Rear view 1 2 3 Figure 2: Rear view 1. Connector compartment cover. Detach to get access to the signal connectors. 2. Display stand cover. Slide it upward and detach it before connecting the signal cables to route the cables neatly. After connecting the cables, re-attach the cover to hide the cables. 3. (Not visible on drawing) Red hook behind the display stand cover to lock/unlock the display height adjust mechanism.
Display parts, controls and connectors When the display is shipped, the display height mechanism is locked to prevent damage during shipping. To unlock the mechanism and adjust the display height, pull out the red hook while pushing down the display panel. Then slowly release the display panel.
Display parts, controls and connectors 9 Figure 4: Connectors front 1. “Left” DVI (digital) video input. See note below. 2. 24 VDC power input. 3. USB upstream connector (to PC). 4. USB downstream connector. If the display’s USB upstream connector is connected to the PC USB bus, you can use the USB downstream connector to connect peripheral USB devices. USB 2.0 devices are supported. 5. +5 Vdc, 0.25 A power output for accessories. 6. +3.3 Vdc, 0.25 A auxiliary power output. 7.
Display parts, controls and connectors USB 2.0 devices are supported. Note: The Barco Coronis Fusion 6MP Display disposes of 2 video inputs. You can connect both video inputs or just one input. • When both inputs are used (DuoView), the signal on the “left” DVI connector (6) is shown on the left side of the screen and the signal on the “right” DVI connector (7) is shown on the right side of the screen.
Connecting the signal cables Connecting the signal cables To connect the signal cables to the display: 1. Unpack the display and put it on a solid flat surface. 2. Make sure the computer is turned off. 3. To get access to the connectors, remove the connector compartment cover (1). To remove the cover, gently lift the clips (2) at one of the handles of the connector cover to release that side of the cover. Then do the same at the other side of the cover. At last remove the cover. 4.
Connecting the signal cables L 4 5 R 6 7 8 Figure 6: Signal cable connections • Connect Head1 of the graphic board to the “left” DVI connector (4) and connect Head2 to the “right” DVI connector (8). (“Left” and “Right” refer to their location for the user looking at the screen.) • Connect a PC USB downstream connector to the display’s USB upstream connector (6) by means of a USB cable. • Connect any USB device to one of the display’s USB downstream connectors (7).
Connecting the signal cables 6. After routing the cables, re-attach the display stand cover. 7. Startup the display. Note: When after startup you wish to change the screen resolution, try to do so in the display control panel on the computer. If you cannot select the desired resolution in the control panel, you need to select the desired resolution in the display OSD by means of the Preferred Input function in the Settings menu.
Connecting the signal cables Recommended resolutions according to OSD selection OSD selection 2x1640x2048 Windows video resolution No.
Connecting the signal cables OSD selection 1x3280x2016 Windows video resolution No. of heads connected 3280x2016@35 Hz 1 1536x2016@50 Hz 2 3072x2016@50 Hz (extend desktop) 2 Result (2) (3) 2x1536x2016 (2) 2x1536x2016 (2) Note: (1) The I-Guard is visible in the top of the active image. Note: (2) Top of the active image is blanked so that the i-Guard is not visible. Note: 44 (3) Not recommended because of low vertical frequency.
Vesa-mount installation Vesa-mount installation Important: • Use an arm that is approved by VESA (according to the VESA 100 mm standard). • Use an arm that can support a weight of at least 25 kg (55.12 lbs). To attach the panel unit to an arm stand: 1. Release the display panel from the display stand as follows: • Remove the neck cover (1) by sliding it upward. • Lift the plastic frame (2) that covers the fixation of the panel to the stand. Turn it for 45 degrees to uncover the fixation screws.
Vesa-mount installation 2. Attach the panel firmly to the arm stand using 4 screws M4 x 10 mm. 3. You should mount the panel in landscape position. Portrait position is not supported.
Cleaning instructions Cleaning instructions Precautions Precautions • Before cleaning, switch the display in stand-by position to prevent the control touch keys from being activated inadvertently by sweeping over the front filter. In stand-by position the touch keys cannot be activated by just sweeping over them. To switch the display on again, you must press the stand-by touch key for a few seconds. • Take care not to damage or scratch the front filter or LCD panel.
Cleaning instructions • Sidolin glass cleaner In case none of the above cleaning products is available, use plain water.
Software installation Software installation 49
Driver and Software Installation Driver and Software Installation This chapter will guide you through the installation of the drivers, software and documentation associated with your Barco Coronis Fusion 6MP Display System or Barco Coronis Fusion 6MP Display(s). Driver and software installation prerequisites Note: To install or remove the drivers, software, or documentation you must be logged on as a user with administrator privileges.
Driver and Software Installation • After you have installed the Barco display controller(s) for your BARCO CORONIS FUSION 6MP Display System in your system for the first time. • After you have reinstalled or upgraded your operating system. • When you upgrade to a newer version of the MXRT driver. Note: You do not need to manually uninstall an existing driver before updating to the current version.
Driver and Software Installation 5. Click "Yes" to accept driver's License Agreement, and then "Next" to continue. Note: In a mixed board configuration (MXRT1150/2150 and MXRT5200/7300), two separate drivers will be installed. The master Install program will make two passes through the driver installation process (i.e. License Agreement, Verify Installation Options, etc.). 6. During installation, there may be a fair amount of display flashing, and the install wizard window may appear on different displays.
Driver and Software Installation attach them to the desktop correctly, please set the resolution of your Barco Display(s) following the instructions in the Configuring Windows section of this manual. Reinstalling drivers You can install new drivers or reinstall existing drivers at any time by using the Barco Set-up wizard on your Barco Coronis Fusion 6MP Display System Installation CD-ROM, see Installing the BARCO MXRT drivers and software, on page 50 of this manual.
Driver and Software Installation Barco MXRT Driver Removal Wizard (driver version may be different than what is pictured) Note: After uninstalling the driver, shutdown the machine and remove the card. If you leave the card in the system, Windows 7 will automatically attempt to reinstall the driver. Silent Installation of Drivers and Software Once A Barco graphics driver has been pre-loaded into the driver store of a Windows 7 OS, subsequent installation of the driver would be intervention-free.
Driver and Software Installation "Always trust software from Barco" and press OK. The PnPUtil will confirm the driver is loaded into the driver store. At this point you can change to another directory and repeat this with other drivers. Since you have indicated that you always trust Barco software, you will not see the trust prompt. If you install using wildcards, you may see an error message that the Autorun.inf was not an expected format. This is expected and is harmless.
Driver and Software Installation (This page intentionally left blank.
Where to get more information Where to get more information 57
Where to get more information Where to find more information The following documentation is included with your system: Document Location Information Quick install sheet System box Brief overview of the complete system set-up Online user guide Installed on the PC Detailed description of the graphic board control panels and display controls and functions Getting started guide (PDF) System CD-ROM This booklet in PDF format Online user guide (PDF) System CD-ROM Same information as the online user
Where to get more information 59
Where to get more information (This page intentionally left blank.
Troubleshooting Troubleshooting 61
General tips General tips • If one display from a multi-head system exhibits problems, try to eliminate the problem by switching video cables or power supplies. In that way you can find out if the problem resides in the display or not.
Configuring Windows Configuring Windows Setting the resolution of your Barco Coronis Fusion 6MP Display Note: In order to set the resolution of your Barco Coronis Fusion 6MP Display you must be logged in using an account with administrator privileges. Accessing the Windows Display Control Panel 1. Right click on the desktop, and select Screen resolution. 2. From the Windows Display Control Panel, hi-lite the Barco display whose mode you wish to set, and select Advanced settings. 3.
Configuring Windows Configuring Clone (duplicate) Mode 1. In the Windows Control Panel, click on Appearance and Personalization. 1. Click on Display. 2. Click on Change Display Settings. 3. In the Multiple Displays drop down list, these options are available (this only appears if there is more than 1 display connected to system): • Duplicate these displays • Extend these displays • Show desktop only on 1 • Show desktop only on 2 4. Select the desired setting.
Technical specifications Technical specifications 65
Technical specifications MDCC 6130 DL: Item 66 Specification Screen technology TFT AM Color LCD Dual Domain IPS-Pro Active screen size (diagonal) 772 mm (30.4") Active screen size (H x V) 654 x 409 mm (25.8 x 16.1") Aspect ratio (H:V) 16:10 Resolution 6MP (3280 x 2048) Pixel pitch 0.
Technical specifications Item Specification Response time (Tr + Tf) 18 ms Scanning frequency (H; V) 30-150 kHz; 15-80 Hz Housing color Black Video input signals DVI-D Dual Link (2x) Video inout terminals NA USB ports 1 upstream (endpoint), 3 downstream USB standard 2.
Technical specifications Item 68 Specification Net weight packaged w/o stand NA Height adjustment range 96 mm Tilt -5° / +25° Swivel -45° / +45° Pivot NA Mounting standard VESA (100 mm) Screen protection Protective, non-reflective glass cover Recommended modalities CT, MR, US, DR, CR, NM, Film Certifications UL 60601-1 1ST EDITION, CAN/CSA-C22.2 NO. 601.
Technical specifications Item Specification Units per pallet NA Pallet dimensions (W x H) NA 69
Technical specifications (This page intentionally left blank.
Warranty Statement Warranty Statement 71
Warranty Statement BARCO MID GENERAL WARRANTY TERMS AND CONDITIONS Applicable from Jan 1st 2008 ARTICLE 1: PRODUCT WARRANTY Barco nv, Medical Imaging Division warrants that the equipment will be free of defects in workmanship or material for the warranty period or the specific period of a warranty extension program.
Warranty Statement new one, ensuring color matching in the event of a diagnostic multi head display configuration. Barco aims to ship the new replacement product within 2 business days after receipt of the Customers notification in writing. ARTICLE 2: CONDITIONS PRECEDENT FOR WARRANTY AND ITEMS EXCLUDED FROM WARRANTY A.
Warranty Statement Eg2. • A display is used at 24 hours/day; ie. 8.760hours/year • The display system is covered with a warranty program of 5 year • The Guaranteed Backlight Lifetime of that model is 17.000hours. • The Factory Calibrated Luminance cannot be achieved anymore after 2.5years, thus corresponding to +/-21.900hours • Result: the backlight replacement does not make part of the warranty coverage.
Warranty Statement performance of its requirements under the warranty condition; failure by Customer to meet its obligations under this paragraph shall excuse Barco nv, MID’s performance hereunder: 3.1 Customer shall not expose Barco nv, MID personnel to any unsafe working conditions. 3.
Warranty Statement be relied upon in inappropriate applications or without proper backup and/or other safety precautions whenever personal injury or property damage may result from failure or error of the product. 8.2 Barco nv, MID shall not be responsible for machine failure and/or its failure to render service or maintenance due to causes beyond its reasonable control.
Warranty Statement 77
Warranty Statement 78
Warranty Statement 79
K5902015-05 January 2011 Barco n.v. President Kennedypark 35 8500 Kortrijk Belgium www.barco.
