EVENTS D320L DIGITIZER INSTALLATION GUIDELINES 15042003 R5976542/00
Barco nv Events Noordlaan 5, B-8520 Kuurne Phone: +32 56.36.89.70 Fax: +32 56.36.88.24 E-mail: events@barco.com Visit us at the web: www.barco.
Changes Barco provides this manual “as is” without warranty of any kind, either expressed or implied, including but not limited to the implied warranties or merchantability and fitness for a particular purpose. Barco may make improvements and/or changes to the product(s) and/or the program(s) described in this publication at any time without notice. This publication could contain technical inaccuracies or typographical errors.
Table of contents TABLE OF CONTENTS 1. Safety ..................................................................................................3 1.1Important Safety Instructions .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 3 1.2Important Warnings . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 4 2. Introduction ....................
Table of contents 2 R5976542 D320L DIGITIZER 15042003
1. Safety 1. SAFETY 1.1 Important Safety Instructions Instructions: • • • • • • • • • • • • • • Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do NOT submerge fully or partly in water or other liquids. Clean only with materials or chemicals that are inert, nonabrasive, noncorrosive and non-marking. Consult the manufacturer for further advice should any doubts exist regarding any cleaning procedure. Do not block ventilation openings.
1. Safety 1.2 Important Warnings Important Warnings: • Risk of electric shock: Image 1-1 Risk of electrical shock • • • • • 4 Risk of electric shock. Do not open. To reduce the risk of electric shock, do not remove cover (or back). No user-serviceable parts inside. Refer servicing to qualified service personnel. The lightning flash with an arrowhead within a triangle is intended to tell the user that parts inside this product may cause a risk of electrical shock to persons.
1. Safety • • Use of an extension cord: If an extension cord is used with this product, make sure that the total of the ampere ratings on the products plugged into the extension cord does not exceed the extension cord ampere rating. Also make sure that the total of all products plugged into the wall outlet does not exceed 15 amperes.
1.
2. Introduction 2. INTRODUCTION 2.1 General functionality Overview The D320L is a video processing device, designed to drive exclusively Barco LED walls. The D320L is capable of handling all standard output formats like SVGA, XGA, SXGA and UXGA on an analog RGBHV and digital DVI output. The D320L Digitizer allows you to control up to 4 sources on one display. Seamless switch from source to source or display sources together, overlay them, customize them.
2. Introduction Type Value Effects Anamorphic imaging, Chroma keying [per input], Alpha keying [per input], Z-order control, Windowing/ View ports Ruggedness IP 10 Dimensions D320L 486 x 482 x 53 (W x D x H) Dimensions D320L input Units 41 x 181 x 103 (W x D x H) Weight ± 7 kg Operating Temperature 0 ºC <> 45 ºC Power consumption 130 Watt max at 85–264 Volt (50–60 Hertz) Stacking Up to 64 units (for 64 different displays) Chaining Up to 64 units (for 256 inputs) 2.
3. Physical Installation of the D320L Digitizer 3. PHYSICAL INSTALLATION OF THE D320L DIGITIZER 3.1 Installation requirements Requirements • • • The D320L Digitizer should not be placed in a built-in installation or enclosure unless proper ventilation is provided. When using the unit in a multi-unit rack assembly or closed assembly, the ambient temperature inside the assembly may not exceed the maximum rated ambient temperature of the Digitizer.
3. Physical Installation of the D320L Digitizer 3.
3. Physical Installation of the D320L Digitizer • • • • • • • • • • A B - : LED-WALL OUTPUT LED wall out (Barco proprietary protocol). RGB HV out (analog). : Power switch The power ON/OFF switch is provide on the rear side of the Digitizer. o Switch pressed to 1 = the unit starts. o Switch pressed to 0 = unit totally switched off. C : Power input - Autoranging from 90 to 260 VAC / 130 Watt. D : LOOP IN - From previous D320L Digitizer. - Panel Link MDR26.
3. Physical Installation of the D320L Digitizer Image 3-3 How to insert an input module into the D320L Digitizer 1. Gently slide in the input module into a free input slot with the grip handle at the top. 2. Locking in the module by pushing the input module completely into the D320L Digitizer until a definite click is audible. Maximum two HDSDI input modules may be inserted in one D320L Digitizer.
4. Input modules 4. INPUT MODULES Overview • • • • • • • DVI input module SDI input module HDSDI input module CVBS / S-VID input module YUV / RG(s)B input module RGB analog input module Dummy input module 4.1 DVI input module Technical info: • • • • • • • • Computer generated graphical source. DVI data in. 162 MHz pixel clock. Resolution from VGA to UXGA/60 Hz. DVI compliant. DVI loop through. Amber LED (upper LED on the front side) will be lit indicating module start up.
4. Input modules 4.2 SDI input module Technical info: • • • • • • • SDI data in. SDI loop through. 270Mbit/s transmission (SMPTE 259M-C). 525/625 interlaced. Coax (75 Ohm). Amber LED (upper LED on the front side) will be lit indicating recognition of film, either continuous or intermittent film detection. When placed in an input slot the green LED (lower LED on the front side) will be lit indicating that the system acknowledges the module. Image 4-3 Image 4-4 Order info: Article No.
4. Input modules Technical info: • • • • • HDSDI data in (SMPTE292M). HDSDI loop through (SMPTE292M). Coax (75 Ohm). When placed in an input slot the green LED (lower LED on the front side) will be lit indicating that the system acknowledges the module. Supported HDSDI standards: - Progressive: o 1280x720/60/1:1/ (SMPTE 296M) o 1280x720/59.94/1:1/ (SMPTE 296M) o 1920x1080/30/1:1/ (SMPTE 274M) o 1920x1080/29.
4. Input modules 4.4 CVBS / S-VID input module Technical info: • • • • Video (BNC) - CVBS : 1Vpp ±3dB (0,7V Video +0,3V Sync) 75 Ohm termination. - BNC loop through connector. S-Video (4 pins DIN) - Y : 1Vpp ±3dB (0,7V Video +0,3V Sync) 75 Ohm termination. - U/V : 0,7Vpp ±3dB 100% color base, 75 Ohm termination. - Chroma : Multi-Standard (PAL / SECAM / NTSC). - 4 pins DIN loop through connector.
4. Input modules Image 4-9 Image 4-10 Order info: Article No. Description R9850940 D320L Digitizer YUV / RG(s)B input module 4.6 RGB analog input module Technical info: • • • • • • • Sub D15 connector for input and loop through. R, G, B, Hsync, Vsync : 0 to 1 Vpp ±3dB 75 Ohm termination. Black level : 300mV. Sync-tip : 0V Resolution : SXGA and UXGA version available. Amber LED (upper LED on the front side) will be lit indicating recognition of film, either continuous or intermittent film detection.
4. Input modules 4.7 Dummy input module Technical info • Dimensions : 103 x 181 x 41(W x D x H) Image 4-13 Image 4-14 Order info: 18 Article No.
5. Cables and accessories for the D320L Digitizer 5. CABLES AND ACCESSORIES FOR THE D320L DIGITIZER 5.1 Cables and accessories List with available cables and accessories Article No. Description Image R326103 Power cable with CEE7 plug. image 5-1 R3261115 Power cable with NEMA 5–15 plug. image 5-2 B5580491 Data cable with RJ12 connectors for RS232 connection between local control PC and COM1 RS232 input port of the master Digitizer.
5.
6. Configuration schemes 6. CONFIGURATION SCHEMES 6.1 Stand alone configuration Scheme Image 6-1 One D320L Digitizer is sufficient to drive one Barco LED wall with four different sources. How to set up a D320L stand alone configuration 1. Connect the RS232 communication port of the local control PC with the COM1 RS232 input port of the D320L Digitizer. 2. Connect the LED-WALL OUTPUT from the D320L Digitizer with the display. 3. Provide the available video sources to the D320L input modules. 4.
6. Configuration schemes The D320L Digitizer can be chained in order to generate more windows on the output display (four windows per D320L Digitizer). How to set up a D320L chaining configuration 1. Connect the RS232 communication port of the local control PC with the COM1 RS232 input port of the first D320L Digitizer. This Digitizer will act as the master, all following Digitizers are slaves. 2. Connect the LOOP OUT with the LOOP IN of the next D320L Digitizer in the chain. 3.
6. Configuration schemes How to set up a D320L stacking configuration 1. Connect the RS232 communication port of the local control PC with the COM1 RS232 input port of the first D320L Digitizer. This Digitizer will act as the master, all following Digitizers are slaves. 2. Connect the LOOP OUT with the LOOP IN of the next stacked D320L Digitizer. This is necessary to avoid synchronization problems between the screens 3.
6. Configuration schemes How to set up a mixed configuration 1. Connect the RS232 communication port of the local control PC with the COM1 RS232 input port of the first D320L Digitizer. This Digitizer will act as the master, all following Digitizers are slaves. 2. Connect the LOOP OUT of each previous Digitizer with the LOOP IN of the next Digitizer. 3. Connect the LED-WALL OUTPUT of the last Digitizer of each chain with a screen.
7. Control Software 7. CONTROL SOFTWARE 7.1 XLite Toolset General introduction The XLite Toolset (R9850042) is used to configure and control the D320L Digitizer from basic set-up to advanced features such as chroma keying, alpha blending or window positioning. Refer to the manual (R5976380) for more information about the XLite Toolset. 7.
7.
8. Maintenance of the D320L Digitizer 8. MAINTENANCE OF THE D320L DIGITIZER 8.1 Cleaning the dust filter The fan intake grill of the D320L Digitizer has a retractable dust filter which must be checked for good functionality on regular basis. Never allow this filter to become blocked up. How to clean the dust filter 1. Softly press down the lid of the dust filter at the rear side of the D320L Digitizer and pull out the filter. (image 8-1) 2.
8.
9. Options 9. OPTIONS 9.1 Overview Order info: Article No.
9.
Index INDEX A Accessories 19 C Cables 19 Cleaning 27 Air dust filter 27 Cabinet 27 Configuration scheme 21–23 Chaining 21 Mixed 23 Stacking 22 Stand alone 21 Configuration schemes 21 Connections 10 D320L 10 D D320L 7–9, 13, 29 Dimensions 8 Functionality 7 Input modules 13 Installation 9 Requirements 9 Options 29 Technical summary 7 I Input module 11, 13–14, 16–18 R5976542 D320L DIGITIZER 15042003 CVBS / S-VID 16 Dummy 18 DVI 13 HDSDI 14 Insert 11 Remove 11 RGB analog 17 SDI 14 YUV / RG(s)B 16 Introduc
Index 32 R5976542 D320L DIGITIZER 15042003
Revision Sheet To: Barco nv Events/Documentation Noordlaan 5, B-8520 Kuurne Phone: +32 56.36.89.70, Fax: +32 56.36.88.24 E-mail: antoon.dejaegher@barco.com, Web: www.barco.