MatrixPRO-II HD/3G SDI series User manual Rev. 1.1 o o Manual #: 26-0903001-00 Revision: 01.
MatrixPRO-II 3G/HD/SD-SDI Routers Rev. 1.1 Copyright © Barco. March 09, 2011 All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or stored in a retrieval system without the prior written consent of Barco. Notice Barco provides this manual “as is” without warranty of any kind, either expressed or implied, including but not limited to the implied warranties or merchantability and fitness for a particular purpose.
MatrixPRO-II 3G/HD/SD-SDI Routers Rev. 1.1 absence of properties guaranteed in writing or due to the intent or gross negligence or part of Barco.
MatrixPRO-II 3G/HD/SD-SDI Routers Rev. 1.1 Company Address Barco, Inc. 11101 Trade Center Drive Rancho Cordova, California 95670 USA Phone: (916) 859-2500 Fax: (916) 859-2515 Barco N.V. Noordlaan 5 8520 Kuurne BELGIUM Phone: +32 56.36.82.11 Fax: +32 56.35.16.51 Website: www.barco.com Technical Support Customer Service Portal — www.barco.com/esupport (866) 374-7878 — Events (24/7) (866) 469-8036 — Digital Cinema (24/7) MatrixPRO-II HD/3G SDI Series –User’s Guide - Rev. 1.
MatrixPRO-II 3G/HD/SD-SDI Routers Rev. 1.1 Operators Safety Summary The general safety information in this summary is for operating personnel. Do not remove panels or covers There are no user-serviceable parts within the unit. Removal of the top cover will expose dangerous voltages. To avoid personal injury, do not remove the top cover. Do not operate the unit without the cover installed.
MatrixPRO-II 3G/HD/SD-SDI Routers Rev. 1.1 Terms in This Manual and Equipment Marking Warning Highlights an operating procedure, practice, condition, statement, etc., which, if not strictly observed, could result in injury to or death of personnel.
MatrixPRO-II 3G/HD/SD-SDI Routers Rev. 1.1 Change History 0.0 1.1 Date ECP # Description Approved By 5/20/10 3/09/11 578607 586286 User’s Guide Added default IP address Added interface commands appendix Added MP-II 3G Configuration Tool GKOU GKOU MatrixPRO-II HD/3G SDI Series –User’s Guide - Rev. 1.
MatrixPRO-II 3G/HD/SD-SDI Routers Rev. 1.1 Contents 1.1 Product versions ..................................................................................................... 10 2 Specifications................................................................................................ 11 2.1 2.1.1 2.2 2.3 2.4 2.5 2.5.1 Mechanics ................................................................................................................ 11 Weight and power consumption ........................
MatrixPRO-II 3G/HD/SD-SDI Routers Rev. 1.1 B.2 Request X-Point Status ....................................................................................................... 31 B.3 Router Ping ......................................................................................................................... 32 B.4 Level List............................................................................................................................. 32 Appendix C Barco MPII-3G Configuration Tool ....
MatrixPRO-II 3G/HD/SD-SDI Routers Rev. 1.1 Product overview This User Manual presents the features, installation and operation procedures of (3G/HD/SDSDI) routers of the Barco MatrixPRO-II series.
MatrixPRO-II 3G/HD/SD-SDI Routers 2 2.1 Rev. 1.1 Specifications Mechanics Dimensions: Safety/Emission Standards: HxWxD = 44x483x50mm, (19”, 1RU); HxWxD = 88x483x50mm, (19”, 2RU); Compliant with CE EN55103-1 and 2. 2.1.1 Weight and power consumption Device Weight 1.3 kg 1.4 kg 2.2 kg 0.35 kg R9004661 R9004660 R9004662 R9871081 2.2 Power 14 W 19 W 35 W Power Supply SL-PWR-40 AC Supply voltage range: AC Mains connector: DC output: DC connector: Status monitoring: Safety standards: 2.
MatrixPRO-II 3G/HD/SD-SDI Routers 2.4 Rev. 1.1 Video specifications Supported formats: Broadcast: - Electrical signal inputs: Standard: Data rate: Connector: Impedance: Return loss: Cable equalization, Electrical signal outputs: Connector: Impedance: Return loss: Signal level: Rise/fall time: Amplitude overshoot: Signal polarity: Signal transition: Timing jitter: Alignment jitter: 270Mbps – 2.97Gbps; DVB-ASI, SMPTE 259M, SMPTE 292M, SMPTE 424M; 2K, 2048x1556/23.98 and 24.
MatrixPRO-II 3G/HD/SD-SDI Routers Field selectivity: Timing range: 2.5 Rev. 1.1 Field 1. • SD, PAL: within clock-intervals (27MHz) 565 – 835 line 6 • SD, NTSC: within clock-intervals (27MHz) 565 – 835 line 10. • HD Tri-Level: 1280x720: within clock-intervals (148.5MHz) 455 – 780 line 7 • HD Tri-Level: 1920x1080: within clock-intervals (148.5MHz) 625 – 1070 line 7.
MatrixPRO-II 3G/HD/SD-SDI Routers 3 Rev. 1.1 Configuration This chapter provides an overview of the configuration options that are available on the Barco MatrixPRO-II 3G/HD/SD-SDI Routers. 3.1 3.2 SW1 – SW4: Address/Level Not Used SW5-SW6: Router mode 3.2.1 Router mode on NxN square routers The nxn square Barco MatrixPRO-II A/V router allows switching in different modes: Router layers 1 layer 2 layers 3 layers 4 layers 8x8 router 8x8 4x4 N.A.
MatrixPRO-II 3G/HD/SD-SDI Routers Rev. 1.
MatrixPRO-II 3G/HD/SD-SDI Routers − Rev. 1.1 3 layers, based on a 16x16 router: Layer 1 1 2 3 4 5 Layer 2 1 2 3 4 5 Layer 3 1 2 3 4 5 Input 1 2 3 4 5 Input 6 7 8 9 10 Input 11 12 13 14 15 Layer 1 1 2 3 4 5 Layer 2 1 2 3 4 5 Layer 3 1 2 3 4 5 Output 1 2 3 4 5 Output 6 7 8 9 10 Output 11 12 13 14 15 In-/Output 16 is not in use in this router setup (3 router layers, based on a 16x16 router).
MatrixPRO-II 3G/HD/SD-SDI Routers Rev. 1.1 In-/Outputs 31 and 32 are not in use in this router setup (3 router layers, based on a 32x32 router).
MatrixPRO-II 3G/HD/SD-SDI Routers Layer 2 1 2 … 8 Layer 3 1 2 … 8 Layer 4 1 2 … 8 3.3 Rev. 1.1 Input 9 10 … 16 Input 17 18 … 24 Input 25 26 … 32 Layer 2 1 2 … 8 Layer 3 1 2 … 8 Layer 4 1 2 … 8 Output 9 10 … 16 Output 17 18 … 24 Output 25 26 … 32 SW7: Power alarm The power alarm can be switched according to the following pattern: SW 7 OFF ON Power alarm Disables Power Alarm Enables Power Alarm Default setting is Power Alarm disabled.
MatrixPRO-II 3G/HD/SD-SDI Routers 3.5 Rev. 1.1 Switching time Switching is performed according to the detected sync reference signal. Switching time is determined by the synchronization signal that feeds the router. This is useful when the video signal has the same format as the synchronization signal. Supported formats are: PAL, NTSC, 750/50p, 750/60p, 1125/50i and 1125/60i. 3.6 Configuring protocol options TCP/IP This is the default option for the Barco MatrixPRO-II HD/3G SDI routers.
MatrixPRO-II 3G/HD/SD-SDI Routers 4 4.1 Rev. 1.1 LED status indication Start-up The LED located at the front of the router indicates the status of the router. At start-up, the LED will alternate between red (R) and green (G) every 500ms for about two seconds. After the start-up sequence the LED will indicate the Alarm state of the router. There are two LEDs located at the Ethernet bus. At start-up the boot loader is searching for update commands on the serial port for about two seconds.
MatrixPRO-II 3G/HD/SD-SDI Routers 5 Rev. 1.1 Router communication You gain access to router for communication purposes by connecting either the router’s serial port to your computer or by using an Ethernet connection. Do not use both the router’s Ethernet port and RS-232 serial port at the same time. Doing so may cause loss of important communication and control data. 5.
MatrixPRO-II 3G/HD/SD-SDI Routers 5.2 Rev. 1.1 Ethernet connection The connections follow the standard set by the IEEE 802.3 100BaseTX specification. The cables that are to be applied should be CAT-5 / CAT-5E standard, or better. It is the responsibility of the installer / user to secure a proper installation of the Ethernet connection. All Barco MatrixPRO-II routers and IP-based Control Panels are connected together through an Ethernet Switch.
MatrixPRO-II 3G/HD/SD-SDI Routers 6 6.1 Rev. 1.1 Control Panel operation Button description A/V Toggle The A/V Toggle button enables/disables audio and video on a specified address. The address can either be read from the dip switches, or be fixed. The button toggles between three states. If the button is pressed for more than 1 second, it will go into a fourth state where both audio and video are disabled. In this state the button will be dimmed.
MatrixPRO-II 3G/HD/SD-SDI Routers Rev. 1.1 Take on/off The Take on/off button enables or disables the Take button. If no take button is defined, Take on/off is always off. On first start-up the take button is enabled. Later it will read the last status from the flash memory. Take The Take buttons LED is normally off. If the Take on/off button is set to “on”, no commands will be sent from the panel until the Take button is pressed.
MatrixPRO-II 3G/HD/SD-SDI Routers Rev. 1.1 7 Environmental Specifications 1. The equipment will meet the guaranteed performance specification under the following environmental conditions: Operating room temperature 0°C to 45°C range: Operating relative humidity range: <95% (non-condensing) 2.
MatrixPRO-II 3G/HD/SD-SDI Routers Rev. 1.1 Appendix A A.1 Materials declaration For product sold into China after 1st March 2007, we comply with the “Administrative Measure on the Control of Pollution by Electronic Information Products”. In the first stage of this legislation, content of six hazardous materials has to be declared. The table below shows the required information.
MatrixPRO-II 3G/HD/SD-SDI Routers Rev. 1.1 A.2 Recycling information Please contact Barco’s Customer Support for assistance with recycling if this site does not show the information you require. Where it is not possible to return the product to Barco or its agents for recycling, the following general information may be of assistance: − Before attempting disassembly, ensure the product is completely disconnected from power and signal connections.
MatrixPRO-II 3G/HD/SD-SDI Routers Rev. 1.1 A.3 Declarations of Conformity DESCRIPTION 3G/HD/SD-SDI Video Routers in the Barco MatrixPRO-II series DIRECTIVES this equipment complies with LVD 73/23/EEC EMC 2004/108/EEC HARMONISED STANDARDS applied in order to verify compliance with Directive(s) EN 55103-1:1996 EN 55103-2:1996 MatrixPRO-II HD/3G SDI Series –User’s Guide - Rev. 1.
MatrixPRO-II 3G/HD/SD-SDI Routers Rev. 1.1 Appendix B Remote Commands Description x X-point Take. ls Status X-point – level. ping Router ping. llist Level list Default Address: 192.168.0.245 port: 4381 Connection to the router will be lost after 20 seconds MatrixPRO-II HD/3G SDI Series –User’s Guide - Rev. 1.
MatrixPRO-II 3G/HD/SD-SDI Routers Rev. 1.1 B.1 X-Point Take This command directly takes the specified X-point. The command specifies which sources to connect to which destinations and on what levels. Several X-point takes can be specified on a single command line. In such cases all specified X-points are taken simultaneously.
MatrixPRO-II 3G/HD/SD-SDI Routers Rev. 1.1 A single X-point Take command can switch multiple X-points. You will however receive one response for each X-point that is switched. Example: Command X l1 1 12 Echo X l1 1 12 Desired action Switch input 1 to output 12 in level 1 B.2 Request X-Point Status This command is used to requests the X-point status of all destinations on a specified level.
MatrixPRO-II 3G/HD/SD-SDI Routers Rev. 1.1 B.3 Router Ping This command is used to check if the router is still responding. Command: ping[*CC] Response: ? "ping" pong [*CC] Example: Command ping Echo pong Desired action B.4 Level List This command is used to the get list of all levels in the system.
MatrixPRO-II 3G/HD/SD-SDI Routers Rev. 1.1 Appendix C Barco MPII-3G Configuration Tool The Barco MPII-3G Tool is a software utility that allows the user to: • Read the IP settings • Modify and Save IP settings • Switching the communication between Ethernet and the serial RS-232 protocols MatrixPRO-II HD/3G SDI Series –User’s Guide - Rev. 1.