Nio display systems Getting Started Guide Supported displays: E-2621, E-3620, MDNG-5121, MDNG-2121, MDNC 3120, MDNC-3121, MDNG-6121
(This page intentionally left blank.
Copyright notice This document is copyrighted. All rights are reserved. Neither this document, nor any part of it, may be reproduced or copied in any form or by any means - graphical, electronic, or mechanical including photocopying, taping or information storage and retrieval systems without written permission of Barco © 2010 Barco N.V. All rights reserved. Notice Although every attempt has been made to achieve technical accuracy in this document, we assume no responsibility for errors that may be found.
(This page intentionally left blank.
Table of Contents Table of Contents Preface ..................................................................................... 7 FCC compliance information............................................................ 8 FCC statement for the display.................................................. 8 FCC statement for the graphic board....................................... 9 CE mark notice ............................................................................... 11 Environmental information .......
Table of Contents Front filter ............................................................................... 51 Cabinet .................................................................................... 52 Software installation ............................................................. 53 Driver and Software Installation ................................................... 54 Driver and software installation prerequisites...................... 54 Installing the BARCO MXRT drivers and software........
Preface Preface 7
FCC compliance information FCC compliance information FCC statement for the display FCC Class B This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC compliance information Chinese notice FCC statement for the graphic board FCC Compliance Information (display controller) Class B: This Barco Graphics Controller complies with part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. this device must accept any interference received, including interference that may cause undesired operation.
FCC compliance information • Consult the dealer or an experienced radio/TV technician for help. The use of shielded cables for connection of the monitor to the graphics card is required to ensure compliance with FCC regulations. Changes or modifications to this unit not expressly approved by Barco could void the user’s authority to operate this equipment.
CE mark notice CE mark notice Declaration of Conformity in accordance with Article 10 (1) of the CE directive This product has been designed and manufactured in accordance with the essential requirements of the Directives 89/336/EEC and MDD 93/42/EEC (class II b product), and for this product the procedures of Annex II have been applied to mark the product with the CE label.
Environmental information Environmental information Disposal Information This product consists of devices that may contain mercury, which must be recycled or disposed of in accordance with local, state, or country laws. (Within this system, the backlight lamps in the monitor display contain mercury.) This equipment has required the extraction and use of natural resources for its production. It may contain hazardous substances for health and environment.
Environmental information Information for China ROHS compliance Table of toxic and hazardous substances/elements and their content, as required by China’s management methods for controlling pollution by electronic information products Toxic or hazardous Substances and Elements Part Name Pb Hg Cd Cr6+ PBB PBDE Metal parts O O O O O O Plastic parts O O O O O O PCB or PCBA O O O O O O LCD panel X X O O O O Power supply/adapter X O O O O O Power cable X O O O O O
Environmental information LCD Monitor 零部件名稱 Γ Γ Γ 有毒有害物質或元素 䪙 ∲ 䬝 Γ ˄Pb˅ ˄Hg˅ ˄Cd˅ ८㺉Ეٙ O O O ႿறᲔٙ O O O O O O ⬉䏃ᵓ㒘ӊ * X X O ⎆䴶ᵓ X O O ⬉⑤ഫ 䗖䜡఼ X O O ⬉⑤㒓 O O O 䚼ֵো䖲㒓 Γ ݁Ӌ䫀 ˄Cr6+˅ O O O O O O O Γ Γ ⒈㘨㣃 ⒈Ѡ㣃䝮 ˄PBB˅ ˄PBDE˅ O O O O O O O O O O O O O O *˖ ⬉䏃ᵓ㒘ӊࣙᣀॄࠋ⬉䏃ᵓঞ݊ᵘ៤ⱘ䳊䚼ӊˈབ⬉䰏ǃ⬉ᆍǃ䲚៤⬉䏃 ǃ䖲఼ㄝ ƻ˖㸼⼎䆹᳝↦᳝ᆇ⠽䋼䆹䚼ӊ᠔᳝ഛ䋼ᴤ᭭Ёⱘ䞣ഛ lj⬉ᄤֵᙃѻકЁ᳝ ↦᳝ᆇ⠽䋼ⱘ䰤䞣㽕∖ᷛޚNJ㾘ᅮⱘ䰤䞣㽕∖ҹϟ h˖㸼⼎䆹᳝↦᳝ᆇ⠽䋼㟇ᇥ䆹䚼ӊⱘᶤϔഛ䋼ᴤ᭭Ёⱘ䞣䍙ߎ lj⬉ᄤֵᙃѻક Ё᳝↦᳝ᆇ⠽䋼ⱘ䰤䞣㽕∖ᷛޚNJ㾘ᅮⱘ䰤䞣㽕∖˗ ԚᰃϞ㸼Ёᠧ Āhā ⱘ䚼ӊˈ݊䞣䍙ߎᰃЎⳂࠡϮ⬠䖬≵᳝៤❳ⱘৃ᳓ҷⱘᡔᴃ 14
Safety Instructions Safety Instructions General Recommendations Read the safety and operating instructions before operating the display. Retain safety and operating instructions for future reference. Adhere to all warnings on the display and in the operating instructions manual. Follow all instructions for operation and use.
Safety Instructions • The medical approved DC power supply must be powered by the AC mains voltage. Power connection - MDNC-3121 • Power requirements: The display must be powered using the delivered medical approved 24 VDC SELV power supply. • The medical approved DC power supply must be powered by the AC mains voltage. Power cords: • Utilize a UL-listed detachable power cord, 3-wire, type SJ or equivalent, 18 AWG min., rated 300 V min.
Safety Instructions the display may fall, causing serious injury to a child or adult, and serious damage to the equipment. More warnings in the Installation chapter. This apparatus conforms to: CE0120 (MDD 93/42/EEC class IIb product), IEC 60601-1, UL 60601-1, CAN/CSA C22.2 No. 601.01-M90 (c-UL), CCC GB4943-1995 (IEC 60950-1). National Scandinavian Deviations for Cl. 1.7.
Recommendations for using your display system Recommendations for using your display system 1. Optimize the lifetime of your display Enabling the Display Power Management System (DPMS) of your display (in the display’s Settings menu) will optimize its diagnostic lifetime by automatically switching off the backlight when the display is not used for a specified period of time. By default, DPMS is enabled on your display, but it also needs to be activated on your workstation.
Recommendations for using your display system diagnostic performance of the product. To ensure optimal product quality, Barco applies strict selection criteria for its LCD panels. To learn more about LCD technology and missing pixels, consult the dedicated white paper available at www.barcomedical.com. 4. Enhance user comfort Every Barco multi-head display system is color matched with the highest specification in the market. Barco recommends keeping color-matched displays together.
Explanation of symbols Explanation of symbols Symbols on the display and / or power supply On the display or power supply, you may find the following symbols (nonrestrictive list): Indicates compliance to the essential requirements of the Directive 93/42/EEC Indicates compliance with Part 15 of the FCC rules (Class A or Class B) Indicates the display is approved according to the UL regulations or or Indicates the display is approved according to the c-UL regulations Indicates the display is approved acc
Explanation of symbols Indicates the display serial no.
Explanation of symbols (This page intentionally left blank.
Introduction Introduction 23
Installation overview Installation overview 1 If applicable, install the graphic board in the computer. 2 Remove the foot rear cover. Pull out the red clip from the tilt & swivel foot. 3 If you wish to rotate the panel, first tilt the panel slightly in order not to damage the tilt & swivel mechanism. 4 Connect the cables: Video (DVI) and power. Route the cables into the provided clips and guides in the tilt & swivel foot.
Installation overview 5 Install software and user manuals. 6 Start up and use MediCal QAWeb Agent. 7 Important Enable DPMS & screensaver for optimal display performance throughout the product lifetime.
Display parts, controls and connectors Display parts, controls and connectors Front view 1 BAR CO 3 2 Figure 1: Front side 1. Power LED The LED is off when the display is disconnected from the power. The LED is also off when the LED function is disabled in the onscreen display (OSD). The LED is green when the display is on (when enabled in the on-screen menus). The LED is orange when the display is in Stand-by power-saving mode. 2. USB downstream port. See also item “7.
Display parts, controls and connectors It allows to put the display in stand-by, navigate through the onscreen display (OSD) menus and change values in the OSD. Rear view of E-2621, E-3620, MDNG-5121 1 2 4 5 6 7 8 9 3 Figure 2: Rear side 1. Connector compartment cover To get access to the connectors, remove the cover by pulling down the 2 clips at the top of the cover. 2. Tilt & swivel foot cover This cover is packed in a separate box when the display is shipped to the customer. 3.
Display parts, controls and connectors When the display is connected to the PC USB bus, you can connect USB devices, such as keyboard, mouse, digital camera, to this connector. 8. DC power input Connect the external power supply, delivered with the display, to this connector. 9. Tilt & swivel foot clip The display is shipped with this clip in the foot to protect the tilt & swivel mechanism during transport. After unpacking, you should remove this clip.
Display parts, controls and connectors 2. Tilt & swivel foot cover This cover is packed in a separate box when the display is shipped to the customer. 3. Tilt & swivel foot 4. DC power input Connect the external power supply, delivered with the display, to this connector. 5. +5 Vdc, 0.25 A power output for accessories. 6. Slot for security cable (e.g., Kensington lock) 7. DVI (digital) video input 8.
Display parts, controls and connectors (This page intentionally left blank.
Display controller installation Display controller installation 31
Display Controller Installation Display Controller Installation Which display controller? Your Barco medical display is compatible with a large range of Barco and non-Barco display controller boards. Depending on the customer’s order details, the display can be delivered with or without display controller. The brochure “Barco medical display overview” on the website www.barco.
Display Controller Installation Types of display controllers for Barco Display Systems The following models of Barco display controllers are available for your display system.
Display Controller Installation Figure 4: Display controller VGA Jumper, VGA enabled Note: To use multiple BarcoMed display controllers in a single computer, you need to enable VGA on only ONE of the BarcoMed display controllers and disable VGA on ALL the other BarcoMed display controllers. To use a BarcoMed display controller with a third party VGA controller or with one or more Barco MXRT display controllers, do NOT enable VGA on the BarcoMed display controller.
Display Controller Installation Installation Procedure The following instructions will take you step by step through the installation of the display controller(s) for your BARCO NIO Display System. CAUTION – Wear a grounded, protective ESD strap when handling or during installation of the display controller. Electrostatic charges can damage the display controller. 1. If you are not going to use your old graphics card, uninstall the drivers and software for it if you have not already done so. 2.
Display Controller Installation 7. Align the display controller(s) for your BARCO NIO Display System with the slot(s) and press it(them) in firmly until the card(s) is(are) fully seated. Note: The next step applies only to the MXRT 5100, MXRT 7100, and MXRT 7200. 8. Connect the power cable(s) to the 6-pin power connection(s) on the graphics card. Make sure the cables are not interfering with anything inside the computer (for example, a cooling fan).
Display Controller Installation 9. Screw in or fasten the display controller securely. Replace and secure the computer cover. 10. Connect your BARCO NIO Displays to the display controller(s) for your BARCO NIO Display System using the cables supplied. Make sure all cables are securely connected before turning on your system.
Display Controller Installation Figure 10: IO-Panel for the Barco MXRT 2100 and Barco MXRT 5200 MXRT 2100 MXRT 5200 X Head 2– DVI-I Connection X Head 1– DVI-I Connection Y Head 1– DVI-I Connection Y Head 2– DVI-I Connection Note: For 6mp, connect Head 1 to left input, and Head 2 to right input. Figure 11: IO-Panel for the Barco MXRT 5100, Barco MXRT 7100 and Barco MXRT 7200 38 X Head 1 – DVI-I Connection Y Stereo Connection This option is not supported by Barco.
Display Controller Installation Note: For 6mp, connect Head 1 to left input, and Head 2 to right input. Figure 12: IO-Panel for the Barco MXRT 7300 X DisplayPort Connections Y DVI-I Connection Note: Disconnecting the DisplayPort cable may lock the display. Note: Only two of the three connectors can be used at a time. Driving three displays is not supported with the MXRT 7300.
Display Controller Installation 12. Turn on the display(s) and then your computer. Turning on your system WARNING - Turn on your display(s) before you turn on your computer. Failure to do so could damage your display(s). If you have properly installed your graphics card, the Windows start-up messages will appear once the boot procedure is finished. Note: Your Barco display(s) will be running in a basic video mode at a default refresh rate.
Display installation Display installation 41
Installation precautions Installation precautions Precautions • Keep your original packaging. It is designed for this display and is the ideal protection during transport. • Avoid reflections in the flat panel to reduce eye strain. • Place the display on a strong and stable table or desk. • Keep the display away from heat sources and provide enough ventilation around the display. • Do not use the display in direct sunlight. • Do not scratch or apply pressure to the screen. This may cause permanent damage.
Installation precautions To remove the clip: 1. Position the display with its rear side facing you. 2. Pull the red clip out of the fixation holes in the foot. 3. Keep the clip in case the display needs to be shipped later. Adjust the panel orientation You can change the orientation of the panel at any time, but it is more convenient to select landscape or portrait orientation before connecting the cables.
Installation precautions Figure 17: Tilt the panel before rotating 3. To change from portrait to landscape, turn the panel counterclockwise. BAR CO Figure 18: To rotate the panel from portrait to landscape 4. To change from landscape to portrait, turn clockwise. Note: If, after installing the display or the system, you change the panel orientation while an image is on the screen, the result depends on the graphic board and the resolution of the image.
Installation precautions rotation). If necessary, change the image resolution in the display control panel and restart the system after changing the orientation.
Connecting the signal cables Connecting the signal cables To connect the signal cables to the display: To get access to the connectors, remove the connector compartment cover by pulling down the 2 clips at the top of the cover. The location of the connectors depends on the display type: 2 1 3 4 Figure 19: Inputs E-2621, E-3620, MDNG-5121 4 1 2 3 Figure 20: Inputs MDNC 3120, MDNC-3121, MDNG-2121 and MDNG-6121 • Connect one end of the DVI cable to the DVI input of the display (1).
Cable routing Cable routing Routing the signal cables • Bind the cables in the connector compartment together with the cable tie inside the connector compartment. • Put the connector compartment cover back on the display. Pay attention that the signal cables are positioned under the bulge in the cover. • Push the cables into the clips on the rear of the tilt & swivel foot.
Cable routing 2. Push the upper side of the cover onto the foot, so that the hooks inside the cover are positioned right under the bulges at the rear of the foot. 3. Slide the cover upward while moving the lower side of the cover towards the foot. 4. Press the cover to the foot so that it makes a clicking sound.
Vesa-mount installation Vesa-mount installation The panel, standard attached to the tilt & swivel foot, is compatible with the VESA 100 mm standard. So it can be used with an arm stand according to the VESA 100 mm standard. Therefore, the tilt & swivel foot must be removed from the panel. Important • Use an arm that is approved by VESA (according to the VESA 100 mm standard). • Use an arm that can support a weight of at least 13 kg (28.66 lbs). To attach the display to an arm stand: 1.
Vesa-mount installation 5. Lift up the round plastic cover. 6. Remove the four screws fixing the foot while supporting the foot. 7. Attach the arm stand firmly to the panel using 4 screws M4 x 8 mm.
Cleaning instructions Cleaning instructions Precautions • Take care not to damage or scratch the front filter or LCD panel. Be careful with rings or other jewelry that can touch the front filter. • Do not apply pressure on the front filter or LCD panel. • Do not apply or spray liquid directly to the front filter, panel or cabinet as excess liquid may cause damage to internal electronics. Instead, apply the liquid to the cleaning cloth.
Cleaning instructions • Detergents with ammonia • Detergents with abrasives • Steel wool • Sponge with abrasives • Steel blades • Cloth with steel thread Cabinet Proceed as follows: • Clean the cabinet using a soft cotton cloth, lightly moistened with a recognized cleaning product for medical equipment. • Repeat with water only. • Wipe dry with a dry cloth.
Software installation Software installation 53
Driver and Software Installation Driver and Software Installation This chapter will guide you through the installation of the drivers, software and documentation associated with your BARCO NIO Display System or BARCO NIO Display(s). The process for the BARCO MXRT family of controllers and BARCOMED family of controllers is handled separately. If you install Barco displays without Barco display controllers, no drivers will be installed. Only the online user manual will be installed on your system.
Driver and Software Installation • Windows XP Professional x64 Edition, • Windows Server 2003, • Windows Server 2003 x64 Edition, • Windows Server 2008, • Windows 2008 x64, and • Windows Vista 32 & 64 Bit Edition. You will need to install the BARCO NIO Display system drivers and software in the following cases: • After you have installed the display controller(s) for your BARCO NIO Display System in your system for the first time. • After you have reinstalled or upgraded your operating system.
Driver and Software Installation b) Click Run. c) Click Browse and browse to the root directory of the BARCO NIO Display System Installation CD-ROM and click on the file, Setup.exe, and click Open. d) Click OK. or a) Browse to the root directory of the BARCO NIO Display System Installation CD-ROM and double click on the file, Setup.exe. 3. Click Next twice. 4. Click Yes to accept the terms of the MediCal QAWeb Agent license agreement.
Driver and Software Installation 10. When the Setup complete message appears, select Reboot System Now and click Finish. 11. After the system reboots, Windows may display either the Digital Signature Not Found message or The software you are installing for this hardware has not passed Windows logo testing.
Driver and Software Installation Figure 24: Barco MXRT Driver Removal Wizard (driver version may be different than what is pictured) Note: Vista Only: After uninstalling the driver, shutdown the machine and remove the card. If you leave the card in the system, Vista will automatically reinstall the driver. If you are uninstalling the Barco MXRT drivers prior to doing a driver upgrade, complete the Barco MXRT Driver Removal Wizard as described, and reboot the system into Safe Mode.
Driver and Software Installation To install the drivers and software silently, please follow the steps below: 1. Insert the BARCO NIO Display System Installation CD-ROM into your CD/DVD drive. When the Barco Product Installation Wizard starts click “Cancel”. 2. Click the Start button in the task bar. 3. Click Run. 4. Click Browse and a) Browse to the root directory of the BARCO NIO Display System Installation CD-ROM. b) Click on the file, Setup.exe, and click Open.
Driver and Software Installation Figure 25: Command line installation Note: When performing an MXRT driver upgrade, it is essential to uninstall the previous installation before installing the new driver. We also recommend that you perfrom the following steps to completely remove the previously installed files: a) Boot the system in safe mode. b) Run MXRT driver cleaner.
Driver and Software Installation • Windows Server 2003 x64 Edition, and • Windows Vista 32 & 64 Bit Edition. You will need to install the BARCO NIO Display system drivers and software in the following cases: • After you have installed the display controller(s) for your BARCO NIO Display System in your system for the first time. • After you have reinstalled or upgraded your operating system. • After you have moved the display controller(s) to a different PCI/PCIe slot. 1. Start your system.
Driver and Software Installation 4. Follow the wizard’s on-screen instructions to complete the installation. Note: When the page shown in figure 26 appears you may either click Next to accept the default settings or if you know the settings required for your viewing application, you may select them now and then click Next. You may change these settings later by accessing the Barco Driver tab within the Windows Display Control Panel.
Driver and Software Installation installing for this hardware has not passed Windows logo testing. Automated display configuration Once the drivers, software and documentation have been installed and your system has been rebooted, the Barco Monitor Plug and Play Software should automatically detect your Barco displays and attach them to the desktop with the correct resolution.
Driver and Software Installation Figure 27: Barco Driver Removal Wizard Command line (Silent) Install of Drivers and Software (Not supported with Windows Vista) Specifying the silent install option causes most of the GUI associated with the installer to disappear. A background progress window will still be visible, but no user input will be required. The silent install behavior is dictated by the SETUP.INI file.
Driver and Software Installation a) Browse to the root directory of the BARCO NIO Display System Installation CD-ROM. b) Click on the file, Setup.exe, and click Open. or a) Browse to the root directory of the location where you saved the contents of your BARCO NIO Display System Installation CD-ROM. b) Click on the file, Setup.exe, and click Open. 5. In the Open address window, place your cursor at the end of the line of text that appears and add the following text after Setup.exe, a space and -silent.
Driver and Software Installation (This page intentionally left blank.
Where to get more information Where to get more information Where to find more information The following documentation is included with your system: Document Location Information Quick install sheet System box Brief overview of the complete system set-up Online user guide Installed on the PC Detailed description of the graphic board control panels and display controls and functions Getting started guide (PDF) System CD-ROM This booklet in PDF format Online user guide (PDF) System CD-ROM Same
Where to get more information • In the Security section, check the option Allow active content to run in files on My Computer 68
Troubleshooting Troubleshooting 69
General tips General tips • If one display from a multi-head system exhibits problems, try to eliminate the problem by switching video cables or power supplies. In that way you can find out if the problem resides in the display or not.
Configuring Windows Configuring Windows Setting the resolution of your BARCO NIO Display Note: In order to set the resolution of your BARCO NIO Display you must be logged in using an account with administrator privileges. Accessing the Windows Display Control Panel 1. Open the “Windows Display Control Panel” by one of the methods below: a) Start > Settings > Control Panel > Display b) Open the “Display Properties Control Panel” by right clicking in an empty area on the desktop, then select Properties.
Configuring Windows If you installed your BARCO NIO Display System drivers in DualView mode (default for Windows XP) there will be a rectangle representing each head controlled by each output of the display controller. This will be true even if you have only one display connected to your BarcoMed controller. Both displays of a display controller cannot be enabled at the same time unless their display properties match.
Configuring Windows above, by right clicking on the rectangle that represents it and selecting Attached. Now repeat steps 5-8 above for this display. If you are using a Quad-Head Configuration repeat all of the above steps for the two displays on the second display controller. Note: If you have a single display configuration and you have enabled DualView, Windows will not allow you to attach the second head. This is normal and not a bug.
Configuring Windows (This page intentionally left blank.
Technical specifications Technical specifications 75
Technical specifications MDNG-2121: Item 76 Specification Picture panel 21.3-inch diagonal viewable screen IPS grayscale liquid crystal display Resolution Native: 1600 x 1200 Display area (H x V) 432.0 x 324.0 (mm) Viewing angle (@ 10/1 contrast) Vertical: 88º Horizontal: 88º Pixel Pitch 0.27 mm (H) x 0.
Technical specifications Item Specification Dimensions (W x H x D) In perpendicular vertical position, highest position, tilt = 0°, swivel = 0°: 385 x 585 x 250 mm Tilt angle -5°/+25° Swivel angle 45° left/right Net weight 12.
Technical specifications E-3620 (MA): Item 78 Specification Picture panel 20.8-inch TFT AM-LCD IPS dual domain Resolution Native: 2048 x 1536 Display area (H x V) 423.9 x 318 (mm) Viewing angle (@ 10/1 contrast) Vertical: 170º Horizontal: 170º Pixel Pitch 0.207 mm (H) x 0.
Technical specifications Item Specification Dimensions (W x H x D) In perpendicular vertical position, highest position, tilt = 0°, swivel = 0°: 385 x 585 x 250 mm Tilt angle -5°/+30° Swivel angle 45° left/right Net weight 13 kg Operating Temperature 0°C to 40°C, 15°C to 35°C within specs Storage Temperature -20°C to 60°C Humidity 8% - 80% (non-condensing) for operation 5% - 95% (non-condensing) for storage Altitude 7500 m storage 2000 m operation 79
Technical specifications MDNG-5121 (MA): Item 80 Specification Picture panel 21.3” Dual domain IPS, normally black Resolution Native: 2560 x 2048 Display area (H x V) 422.4 x 337.92 mm Viewing angle (@ 10/1 contrast) Vertical: 170º Horizontal: 170º Pixel Pitch 0.165 mm (H) x 0.
Technical specifications Item Specification Dimensions (W x H x D) In perpendicular vertical position, highest position, tilt = 0°, swivel = 0°: 408 x 591 x 250 mm Tilt angle -5°/+30° Swivel angle 45° left/right Net weight 11.
Technical specifications MDNC 3120 (MA): Item 82 Specification Picture panel 20.8” TFT AM LCD, Dual domain IPS, color Resolution Native: 2048 x 1536 Display area (H x V) 423.9 x 318.0 Viewing angle (@ 10/1 contrast) Vertical: 170º Horizontal: 170º Pixel Pitch 0.207 mm (H) x 0.
Technical specifications Item Specification Dimensions (W x H x D) In perpendicular vertical position, highest position, tilt = 0°, swivel = 0°: 385 x 585 x 250 mm Tilt angle -5°/+30° Swivel angle 45° left/right Net weight 13 kg Operating Temperature 0°C to 40°C, 15°C to 35°C within specs Storage Temperature -20°C to 60°C Humidity 8% - 80% (non-condensing) for operation 5% - 95% (non-condensing) for storage Altitude 7500 m storage 2000 m operation 83
Technical specifications MDNC-3121: Item 84 Specification Picture panel 21.3” LCD, IPS, color Resolution Native: 2048 x 1536 Display area (H x V) 433.152 x 324.864 Viewing angle (@ 10/1 contrast) Vertical: 88º Horizontal: 88º Pixel Pitch 0.2115 mm (H) x 0.
Technical specifications Item Specification Dimensions (W x H x D) In perpendicular vertical position, highest position, tilt = 0°, swivel = 0°: 385 x 585 x 250 mm Tilt angle -5°/+30° Swivel angle 45° left/right Net weight 13 kg Operating Temperature 0°C to 40°C, 15°C to 35°C within specs Storage Temperature -20°C to 60°C Humidity 8% - 80% (non-condensing) for operation 5% - 95% (non-condensing) for storage Altitude 7500 m storage 2000 m operation 85
Technical specifications E-2621 (MA): Item 86 Specification Picture panel 21.3-inch diagonal viewable screen TFT (thin film transistor) active matrix, grayscale liquid crystal display Resolution Native: 1600 x 1200 Display area (H x V) 432.0 x 324.0 (mm) Viewing angle (@ 10/1 contrast) Vertical: 160º Horizontal: 160º Pixel Pitch 0.27 mm (H) x 0.
Technical specifications Item Specification Dimensions (W x H x D) In perpendicular vertical position, highest position, tilt = 0°, swivel = 0°: 385 x 585 x 250 mm Tilt angle -5°/+30° Swivel angle 45° left/right Net weight 14 kg Operating Temperature Operation: 0°C to 40°C Within specs: 15°C to 35°C Storage Temperature -20°C to 60°C Humidity 8% - 80% (non-condensing) for operation 5% - 95% (non-condensing) for storage Altitude 7500 m storage 2000 m operation 87
Technical specifications MDNG-6121: Item 88 Specification Picture panel 21.3-inch diagonal viewable screen IPS grayscale liquid crystal display Resolution Native: 2800 x 2096 Display area (H x V) 432.6 x 324.5 (mm) Viewing angle (@ 10/1 contrast) Vertical: 85º Horizontal: 85º Pixel Pitch 0.154 mm (H) x 0.
Technical specifications Item Specification Dimensions (W x H x D) In perpendicular vertical position, highest position, tilt = 0°, swivel = 0°: 385 x 585 x 250 mm Tilt angle -5°/+25° Swivel angle 45° left/right Net weight 12.
Technical specifications (This page intentionally left blank.
Warranty Statement Warranty Statement BARCO MID GENERAL WARRANTY TERMS AND CONDITIONS Applicable from Jan 1st 2008 ARTICLE 1: PRODUCT WARRANTY Barco nv, Medical Imaging Division warrants that the equipment will be free of defects in workmanship or material for the warranty period or the specific period of a warranty extension program.
Warranty Statement Replacement parts used shall be new or equivalent to new parts for the revision level of the equipment. A replacement LCD panel will be new or similar run time. The warranty period for the replacement parts will expire at the same moment as the original warranty period of the equipment. All parts replaced hereunder and returned to Barco nv, MID (or an authorised service centre) shall become the property of Barco nv, MID (or the authorised service centre). 1.
Warranty Statement 2.5 Repair or replacement of consumables1 or specific parts that by definition are subject to wear and tear, including but not limited to: a.CRT’s, LCD panels b.Backlights in diagnostic LCD displays, when the backlight run time2 is beyond the Guaranteed Backlight Lifetime3 of that model, when used at the Factory Calibrated Luminance4 Eg1. • A display is used at 8 hours/day; ie. +/-2.
Warranty Statement Replacement of moveable parts such as power cords, remote controls, … 2.7 Any product disassembly and installation costs at the operation site, travel expenses and travel time to and from the operation site for the personnel in charge of the repair works and transport charges. 2.
Warranty Statement remedy and Barco's sole and exclusive liability for Barco’s breach of the Warranties hereunder. BARCO NV, MID SHALL NOT UNDER ANY CIRCUMSTANCES BE LIABLE TO CUSTOMER OR ANY THIRD PARTY FOR DIRECT, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, SUCH AS BUT NOT LIMITED TO, DAMAGE TO OR LOSS OF TANGIBLE OR INTANGIBLE PROPERTY OR EQUIPMENT, LOSS OF PROFITS OR REVENUES, COST OF CAPITAL, COST OF PURCHASE OF REPLACEMENT GOODS, OR CLAIMS OF USER FOR SERVICE INTERRUPTIONS.
Warranty Statement (This page intentionally left blank.
Warranty Statement (This page intentionally left blank.
Warranty Statement (This page intentionally left blank.
Warranty Statement (This page intentionally left blank.
B410582-05 March 2010 Barco nv Medical Imaging President Kennedypark 35 B-8500 Kortrijk, Belgium www.barco.