D-Cine Premiere DP100 User’s manual R9010111 R9010118 R5976907/00 02/11/2005
Barco nv Digital Cinema Noordlaan 5, B-8520 Kuurne Phone: +32 56.36.84.93 Fax: +32 56.36.88.62 E-mail: info.bdc.bps@barco.com Visit us at the web: www.barco.
Federal Communications Commission (FCC Statement) This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Table of contents TABLE OF CONTENTS 1. Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.1 1.2 1.3 1.4 1.5 1.6 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of contents 2 R5976907 D-CINE PREMIERE DP100 02/11/2005
1. Safety Instructions 1. SAFETY INSTRUCTIONS Overview • General • Warning Risk of Fire • Ventilation • Service • Optical performances • Cabinet maintenance 1.1 General Summary • This equipment is intended for installation in a restricted access location. • Before operating your projector, please read this manual thoroughly, and retain it for future reference. • Installation and preliminary adjustments should be performed by qualified Barco personnel or authorized Barco service dealers.
1. Safety Instructions 1.4 Service Protection on Servicing Attempt to alter the factory-set internal controls or to change other control settings not specially discussed in this manual can lead to permanent damage to the projection unit and cancellation of the warranty. Servicing Do not attempt to service this projector yourself, as opening or removing covers may expose you to dangerous voltage potential and risk of electric shock! Refer all projector servicing to a qualified Barco service center.
2. Check up the D-Cine Premiere DP100 2. CHECK UP THE D-CINE PREMIERE DP100 Which parts have to be checked before starting up! • All covers in place and access doors closed • Power connection to wall outlet • Pressure in the cooling system of the DMD’s. • Exhaust on dirt 2.
2. Check up the D-Cine Premiere DP100 2.2 Power Connection to Wall Outlet Power plugged into wall outlet! Image 2-3 Power connection to Wall outlet 2.3 Pressure in the Cooling System Access to the manometer 1. Insert the lock key in the keyhole on the lamp house door and turn the key to the right to unlock the door. (image 2-4) 2. Turn the door to the right to open.
2. Check up the D-Cine Premiere DP100 Max. Min. Image 2-5 Manometer view A rapid/significant drop in system pressure indicates leakage. Verify whether the circuit shows any visible signs of liquid leakage. Refer the problem to a qualified Barco service center. Minor drops in pressure over time are to be expected. Once the minimum pressure is reached, pre-pressurize to approximately 1 bar (projector off).
2.
3. Starting up the D-Cine Premiere DP100 3. STARTING UP THE D-CINE PREMIERE DP100 Overview • Switching On the projector • Starting Image Projection 3.1 Switching On the projector How to switch On the projector 1. First, carry out the projector check up (see "Check up the D-Cine Premiere DP100", page 5). 2. Press the tumbler switch (A) in the “I” position (ON state indicated by a visible red section of the switch).
3.
3. Starting up the D-Cine Premiere DP100 3.2 Starting Image Projection Overview • Using the Button control Panel • Using the Touch Screen Panel 3.2.1 Using the Button control Panel How to start image projection 1. Press the lamp ignition button (A). (image 3-4) The lamp ignite, indicated by the built-in Green LED ON (A2). 2. After ignition of the lamp, press the dowser button (B) (image 3-4) The dowser opens, indicated by the built-in Green LED ON (B2). 3.
3. Starting up the D-Cine Premiere DP100 3.2.2 Using the Touch Screen Panel How to start image projection 1. Start lamp ignition and opening dowser with the toggle buttons on the control panel (see "Using the Button control Panel", page 11). 2. Successively press touch button Home and Macro’s. (image 3-5) The macro menu is displayed. The macro which is active is displayed next to field with inscription “Active”.
4. Cinema Operation 4. CINEMA OPERATION Introduction This section explains how trained operators can use the projector for presenting cinema events such as first-run movies stored an a digital media storage device. The digital media storage device or cinema server is connected to one of the A or B input port on the input panel. Input Panel B A Cinema Server to SMPTE A or B Image 4-1 Cinema server connection 4.1 Selecting the Cinema Source Using the Button control panel 1.
4. Cinema Operation The assigned macro is activated resulting in a full image display according the cinema processing procedure (pre-defined by the producers).
5. Non-Cinema Operation 5. NON-CINEMA OPERATION Overview • ACSAR 2 Input facilities • Monitoring ACSAR 2 selected Source • Selecting an ACSAR 2 Source • Remote Control Functionality Introduction This section explains how to display “alternative content” originating from a standard definition or high definition non-cinema source. Such a source routes to a DVI (Digital Visual Interface) port in the D-Cine Premiere DP100 projector head, and bypass cinema processing when selected.
5. Non-Cinema Operation RGBHV Image 5-2 Monitoring ACSAR 2 output signal 5.3 Selecting an ACSAR 2 Source About Macro’s files For any display, the projector interprets incoming signal data according to a selectable “Macro file” defined at the time of installation or later (e.g. with each subsequent release of a new digital cinema feature), and stored in projector memory.
5. Non-Cinema Operation The macro will be executed, resulting in a full image display of the source connected to the respective input module of the ACSAR 2. Because these macros are also assigned to a button on the control panel, the LED associated to the button will be On. Image 5-4 Macros selection 5.4 Remote Control Functionality 5.4.
5. Non-Cinema Operation 5.4.2 Remote Control Functions Function of the RCU keys Menu keys IR LED No function Address key Pause On/Off Lamp On/Off Lens keys No function Macro keys ACSAR Input Image Freeze Text On/Off Image keys No function Image 5-6 Function of the RCU keys Ref. Key name Description 1 Menu keys Keys used to enter, to exit, to scroll in....the menus 2 Address key (Recessed key) Allows to match the address of the projector.
5. Non-Cinema Operation Ref. Key name Description 10 Text On/Off Press to deactivate or reactivate the On Screen Dialog Boxes and Menus on projection screen (not applicable on the image preview monitor). 11 Image keys Use these keys to adjust the image display performances. PHASE key: adjustable for Data sources only. TINT key: adjustable for NTSC video sources only. 5.4.
5.
6. Switching Off the D-Cine Premiere DP100 6. SWITCHING OFF THE D-CINE PREMIERE DP100 Procedure for switching off the projector • Close the dowser. • Switch off the lamp • Switch off the projector 6.1 Stop Image Projection How to stop image projection 1. Press the dowser button (B). (image 6-1) The dowser shuts, indicated by the built-in Red LED ON (B1). 2. Press the lamp ignition button (A) (image 6-1). The lamp turns off, indicated by the built-in Red LED ON (A1).
6.
7. Maintenance of the D-Cine Premiere DP100 7. MAINTENANCE OF THE D-CINE PREMIERE DP100 Overview • Lamp Unit replacement 7.1 Lamp Unit replacement Overview 7.1.1 • Removal of the Lamp House • Installation of the Lamp Unit Removal of the Lamp House 7.1.1.1 Access to lamp Unit How to access the lamp unit 1. Insert the lock key in the keyhole on the lamp house door. (image 7-1) 2. Turn the key to the right to unlock the door. 3. Turn the door to the right to open. Image 7-1 Access to lamp casing 7.
7. Maintenance of the D-Cine Premiere DP100 C A B A C Image 7-2 Lamp casing removal 7.1.2 Installation of the Lamp Unit 7.1.2.1 Installation of the lamp unit in the projector head How to install the lamp unit 1. Place the lamp unit on the lamp base in the projector, lining up the lamp unit foot with the slots on the base. (image 7-3) 2. Push the lamp unit foot fully into the slots. (image 7-4) 3. Secure the position of the lamp unit by tightening the spring screws (A). 4.
7. Maintenance of the D-Cine Premiere DP100 A A Image 7-4 Securing the lamp unit Before using the lamp, Insert the lamp parameters via the D-Cine Communicator software. 7.1.2.2 Closing the Lamp house door Installation of a new lamp requires alignment of the lamp position when installed in the projector head. Therefore, first proceed to lamp alignment before closing the lamp house door. How to lock the lamp house door 1. Close the door. (image 7-5) 2. Turn the key counterclockwise to lock the door.
7.
8. Cleaning Air Duct 8. CLEANING AIR DUCT Overview • Cleaning the Blower on top of the Projector Head • Cleaning the Dust filters 8.1 Cleaning the Blower on top of the Projector Head This item should be cleaned approximately every six months under normal environment conditions. Equipment in very dusty or otherwise contaminated areas may require more frequent maintenance.
8. Cleaning Air Duct Location of the air filters Air filters are placed at the front (A) and at the right side (B) of the projector head. A Image 8-2 Air filter at the front of the projector B Image 8-3 Air filter at the side of the projector Removing the air filters 1. Front air filter: grasp the decorative bar of the filter (A) and pull out the air filter of the projector front cover. 2.
9. Image Control 9. IMAGE CONTROL 9.1 Lens Focus test pattern How to select a test pattern for focus alignment 1. On the touch screen panel, starting from the Home screen, consecutively press touch button Home (1), Patterns (2) and More (3). (image 9-1) The name of the already active test pattern is indicated just below the screen field Active Test Pattern. 2. Touch the arrow buttons on both sides of the screen field Enable Test Pattern to select the Focus test pattern from the list.
9. Image Control Lens zoom can be performed without removing any cover. 9.2.1 Preparation of the projector Removing both side panels 1. Loosen the 2 screws on top side and the 2 screws on the bottom side of the cover nearest the lens. (image 9-3) 2. Tilt the cover a little and lift up for removal. Image 9-3 Right side cover removal Loosen the dust sock around the lens 1.
9. Image Control Image 9-5 Lens Zoom 9.2.3 Lens Focus The focus adjustment is located just below the lens on the left side (C on image 9-6). Remove the side cover nearest the lens and open the dust sock around the lens. How to focus? 1. Loose fixation nut C1. (image 9-6) 2. Turn the knurled torque knob (C2) to the left or to the right until the center of the image is focused (sharp image). 3. Fasten screw C1 again to secure the focus position. C1 C2 C Image 9-6 Focus adjustment 9.2.
9. Image Control 2. Shift the image by turning the knurled torque knob (A2) clockwise or counter clockwise until the image is on the desired position. 3. Secure this position by fastening nut A1 again. 4. For a horizontal shift, loosen first fixation nut B1. 5. Shift the image by turning the knurled torque knob (B2) clockwise or counter clockwise until the image is on the desired position. 6. Secure this position by fastening nut B1 again.
10. Status of the D-Cine Premiere DP100 10. STATUS OF THE D-CINE PREMIERE DP100 Status lights On top of the projector head, rear side, status lights are built-in in the corners. When no errors, e.g. fan failure, overheating.. are detected, the color of the status lights is GREEN. When an error occurs, the color of the status lights changes to RED. Information about the type of error can be retrieved using the D-Communicator or the Touch panel menu.
10. Status of the D-Cine Premiere DP100 Image 10-4 Status start up Image 10-5 Status menu Overview of the Status menu The status menu contains the following items: • Temperature overview • Voltage overview • Fan speeds overview 10.2 Temperature overview To get DMD temperatures and lamp house temperature 1. Push Temperature. (image 10-6) The DMD and lamp house temperature overview will be displayed.
10. Status of the D-Cine Premiere DP100 The switched mode power supply temperatures are listed.
10. Status of the D-Cine Premiere DP100 Image 10-12 10.3 Voltage overview First voltage overview 1. Push Voltages. (image 10-13) The first voltage menu will be displayed. (image 10-14) The following voltages are monitored: - 5V standby - 12V standby - 3.3V - 12V Image 10-13 Status voltages selected Image 10-14 First voltage overview menu Second voltage overview 1. Push More →.
10. Status of the D-Cine Premiere DP100 The second voltage overview window will be displayed. (image 10-16) The following voltages are monitored: - Lamp fan Top - Lamp fan Anode - Lamp fan Cathode - Electronic fans Image 10-15 Selecting second voltage overview Image 10-16 Second voltage overview window Third voltage overview 1. Push More →. (image 10-17) The third voltage overview window will be displayed.
10. Status of the D-Cine Premiere DP100 Image 10-19 Fan speed selected Image 10-20 Fan speed overview window Second fan speed window 1. Push More →. (image 10-21) The second fan speed overview window will be displayed. (image 10-22) The following fans are monitored: - Fan sealing - Fan lamp top - Fan lamp anode - Fan lamp cathode Image 10-21 Selecting second fan speed overview Image 10-22 Second fan speed overview window Third fan speed window 1. Push More →.
11. D-Cine Premiere DP100 Info 11. D-CINE PREMIERE DP100 INFO 11.1 Starting up the Menu How to select! 1. On the touch screen panel, starting from the Home screen, consecutively press touch button Home and Projector. (image 11-1) On the touch screen appears two fields, named the Lamp Info and the projector Properties. 2. Press the respective touch button to consult the stored info behind (see further). 2 1 Image 11-1 Projector Info 11.2 Lamp info Run times and strikes 1. Push Lamp info.
11. D-Cine Premiere DP100 Info The second lamp info menu will be displayed. (image 11-5) The following information is given: Power Actual power supplied to the lamp Nominal power Nominal power to be supplied to the lamp Maximum power Maximum power allowed to be supplied to the lamp Minimum power Minimum power allowed to be supplied to the lamp Maximum current Maximum current through the lamp Image 11-4 More lamp info Image 11-5 Lamp power info Administrative information 1. Push More →.
11. D-Cine Premiere DP100 Info 11.3.1 Projector properties start up How to start up 1. Push Properties. (image 11-8) The properties window opens. (image 11-9) Image 11-8 Projector properties selected Image 11-9 Properties window 11.3.2 IP addresses projector Use the D-Cine Communicator software to setup the IP addresses. IP Internet Protocol. The network layer of TCP/IP. Required for communication with the internet.
11. D-Cine Premiere DP100 Info The IP overview list will be displayed. (image 11-11) Projector IP IP address of built-in Barco controller DIM-PC. Subnet mask subnet mask address Default gateway Default gateway address (router address DHCP enabled : dynamic IP address used on the projector disabled : fixed IP address used for the projector Note: An enabled DHCP, ALWAYS requires an installed network connection to the projector.
11. D-Cine Premiere DP100 Info Image 11-12 IP cinema selected Image 11-13 IP cinema overview 11.3.4 Communication Overview 1. Push Communication. (image 11-14) An overview of the communication settings will be given. (image 11-15) Projector address communication address of the projector Baudrate communication velocity Mode RS232 or RS422 RS422 Termination ON or OFF. Only used when Mode is RS422. Image 11-14 Communication properties selected Image 11-15 Communication properties 11.3.
11.
Index INDEX A Access doors 5 Check up 5 ACSAR 2 selected source Monitoring 15 Air duct 27 Cleaning 27 15 B Blower 27 Cleaning 27 Button control panel 11 Image projection 11 Removal 23 Lamp house door 25 Closing 25 Lamp unit 23–24 Access 23 Installation 24 Removal 23 Replacement 23 Lens adjustment 29–31 Focus 31 Projector preparation 30 Zoom 30–31 Lens focus 29 M C Check up 5 Access doors 5 Covers 5 Projector 5 Cinema operation 13 Cinema source 13 Selecting 13 Cleaning 27 Air duct 27 Blower 27 Dust filt
Index Image projection Switching off 21 Projector 21 Switching On 9 Projector 9 21 T Touch panel 33–34, 36–37, 39–43 Projector functions 39–43 Communication 43 IP addresses projector 41 46 IP cinema 42 Lamp info 39 Properties 40 Properties start up 41 Touch panel properties 43 Status 33–34, 36–37 Fan speed 37 Startup 33 Temperature 34 Voltage 36 Touch screen panel 12 Image projection 12 R5976907 D-CINE PREMIERE DP100 02/11/2005
Revision Sheet To: Barco nv Digital Cinema/Documentation Noordlaan 5, B-8520 Kuurne Phone: +32 56.36.84.93, Fax: +32 56.36.88.62 E-mail: service.digitalcinema@barco.com, Web: www.barco.
