SF-10V display Installation manual R59770542/01 10/02/2012
Barco nv LiveDots President Kennedypark 35, B-8500 Kortrijk Phone: +32 56.23.32.11 Fax: +32 56.26.22.62 Support: www.barco.com/esupport Visit us at the web: www.barco.
Changes Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied warranties or merchantability and fitness for a particular purpose. Barco may make improvements and/or changes to the product(s) and/or the program(s) described in this publication at any time without notice. This publication could contain technical inaccuracies or typographical errors.
Table of contents TABLE OF CONTENTS 1. Safety . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 3 1.1 1.2 1.3 Safety guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of contents 2 R59770542 SF-10V DISPLAY 10/02/2012
1. Safety 1. SAFETY About this chapter Read this chapter attentively. It contains important information to prevent personal injury while installing the SF-10V display. Furthermore, it includes several cautions to prevent damage to the SF-10V tile. Ensure that you understand and follow all safety guidelines, safety instructions and warnings mentioned in this chapter before installing the SF-10V display.
1. Safety 1.1 Safety guidelines Personal protection WARNING: Ensure you understand and follow all the safety guidelines, safety instructions, warnings and cautions mentioned in this manual. WARNING: Be aware of suspended loads. WARNING: Wear a hard hat to reduce the risk of personal injury. WARNING: Be careful while working with heavy loads. WARNING: Mind your fingers while working with heavy loads.
1. Safety 1.2 Important safety instructions Instructions: • Read these instructions. • Keep these instructions. • Heed all warnings. • Follow all instructions. • Clean only with materials or chemicals that are inert, nonabrasive, noncorrosive and non-marking. Consult the manufacturer for further advice should any doubts exist regarding any cleaning procedure. • Do not block ventilation openings. Install in accordance with the manufacturers instructions.
1. Safety 1.3 Important warnings Important warnings: Risk of electric shock: Do not open. To reduce the risk of electric shock, do not remove cover (or back). Remove all power and data cabling before opening the device for service purposes. No user-serviceable parts inside. Refer servicing to qualified service personnel. Maximum and minimum ambient temperature: The maximum ambient temperature for the LED wall is 45°C, the minimum temperature is -20°C.
2. SF-10V tiles 2. SF-10V TILES About this chapter This chapter described the SF-10V, modular outdoor LED tile.
2. SF-10V tiles 2.1 SF-10V tile Tile overview The front and back view of the SF-10V tile. Image 2-1 Packing For safe transportation, the SF-10V tiles are stored in a secure way. every tile have its separate package, Maxium 4 SF-10V packages that inner hold the tile can stand in a big wooden pallet. Image 2-2 The weight 8 SF-10V 1 tile 79.
2. SF-10V tiles 2.2 Stacking SF-10V packages Stacking possibilities for SF-10V packages Image 2-3 WARNING: Only the configurations illustrated above can be used for stacking. Other configurations will damage the SF-10V tiles.
2.
3. Installation requirements 3. INSTALLATION REQUIREMENTS About this chapter This chapter enumerate the mechanical requirements for the SF-10V display, the electrical requirements to power up the SF-10V display and the system requirements to run the control software efficient.
3. Installation requirements 3.1 Mechanical requirements for the SF-10V display Support structure The support structure can be provided and installed by the customer because they vary from system to system. Although, the following must be taken into account and must be precisely calculated on individual basis: 1.
3. Installation requirements WARNING: 90% energy is transferred into heat, which requires a certain amount of airflow at the rear of the SF-10V display. For that sufficient free space should be available behind the display to ensure a good ventilation. The higher the display the more free space is required.
3. Installation requirements 3.2 Electrical requirements for the SF-10V display Power requirements One SF-10V tile requires 220-240 VAC, 50-60 Hz, 5.72 amps at 230 VAC. Note that one SF-10V tile correspond with a display surface of 1,23 m². Power link cables are used to link the power from tile to tile. However, MAXIMUM two (2) tiles, may be connected in parallel. So, one power source cable has to be provided per two (2) tiles.
3. Installation requirements 3.3 System requirements for the Control software Before you begin It is assumed you are familiar with the Windows operating system at your site. The CD-ROM in your package contains a Windows-based installation program. You can install the software from the CD-ROM.
3.
4. System overview 4. SYSTEM OVERVIEW About this chapter This chapter enumerates the fundamental elements of an SF-10V screen display.
4. System overview 4.1 Introduction The fundamental elements of an SF-10V screen display system are: • SF-10V tiles. • Control PC. • LED Image Processor. • Power box. • Control software.
4. System overview LED-wall Sources Video Processor Tile 1 TCP/IP Tile 2 Control PC Power box Tile 3 Image 4-2 If the LED Image Processor is DX–700 and DX-100 use the TCP/IP connection with the control PC.
4. System overview 4.2 SF-10V tile Introduction SF-10V tile The SF-10V series is designed for ultra-large outdoor LED display installations. The SF-10V tile can overlay video and data sources in their native quality. A unique video processing feature enables the creation of a visual resolution quasi double the physical resolution defined by the cluster of LED’s spread on the surface of the display. The SF-10V tile is an IP65 rating in front of side and an IP43 rating in back of side.
4. System overview Image 4-4 Power link cable of 1,5 meter (R9850241).
4. System overview Image 4-5 Dummy power plug (R9850280). Data cables used between SF-10V tiles To meet the demands of each SF-10V application Barco offers several lengths of data cables to link data from tile to tile. Note that the data output port of the last SF-10V tile in the data chain has to be sealed with a dummy data plug.
4. System overview Image 4-6 Data linking cable of 1,5 meter (R9850210).
4. System overview Image 4-7 Dummy data plug (R9850270).
4. System overview 4.3 Power boxes General To ensure safe and reliable operation of the SF-10V display, a suitable system for AC power distribution must be used. Though 3 rd. party solutions may be used, several sizes and types of power distributions are available from Barco. For smaller system the “Mono Phase Power Box” can be used, medium sized system may use on of several custom power box solutions. Image 4-8 Mono phase power box. Image 4-9 Custom power box.
4. System overview 4.4 Video Processor General The Video processor processes (image processing, conversion and conditioning) all source signals for digital distribution to every tile as well as providing a user interface for complete system setup monitoring and control. The video processor can be accessed directly or via the control software (e.g. DTS). This software is designed as a user interface to be used in conjunction with the Video processor and display.
4. System overview CAUTION: Refer to the manual(s) of the used video processor for more information about installation and usage guidelines. D320 The D320L is a video processing device, designed to drive as well Barco LED walls as large screen projectors, monitors, plasma screens, ... etc. The D320L is capable of handling all standard output formats like SVGA, XGA, SXGA and UXGA on an analog RGBHV and digital DVI output. The D320L digitizer allows you to control up to 4 sources on one display.
4. System overview 4.5 Control software General The control software is designed as a graphic user interface (GUI) and can be used to control and configure the digitizer as well as the Barco LED wall via a PC (e.g. Director toolset). Minimum required software version: 2.04 Image 4-14 Control software “Director toolset”. Remote management software (RMS) The RMS-1 software is designed to configure, manage, and monitor Barco digital signage LED display systems.
4. System overview 4.6 Fiberlink system General If the distance between the digitizer and the LED-wall exceeds 5 meters, a fiber optic connection must be used to ensure signal integrity and system reliability. Barco offers two complete system solutions including transmitter, fiber and receiver. The choice of system depends on the length of cable required. Image 4-16 “Fiberlink 2” transmitter and receiver.
4.
5. Physical installation 5. PHYSICAL INSTALLATION About this chapter The setup process below describes roughly the installation stages to follow to install a SF-10V display. Several stages refer to one or more detailed and illustrated procedures which are also described in this installation manual. WARNING: Safety first. Fence off the installation area before starting to install your SF-10V display.
5. Physical installation 5.1 Installation of the support structure What has to be done? The complete support structure has to be assembled and installed in its final position. Screen supporting/securing structures vary from system to system. Consult Barco for advise on professional rigging organizations. SF-10V mounting plates. Barco provides mounting plates for the SF-10V tiles which can be used to clamping the tiles to the support structure. A B Image 5-1 A Middle mounting plate.
5. Physical installation 5.2 Mounting the SF-10V tile Necessary tools • 17 mm open-end wrench. • 17 mm box-end wrench. • 14 mm long allen key. • Scaffold or Z-lift. Necessary parts • SF-10V tiles • Four M10x90 bolts per tile (DIN931 hex cap bolts and partially thread - steel zinc plated). Reference A. • Four M10 plain washer per tile (DIN433 - steel zinc plated). Reference B. What has to be done? The SF-10V tiles have to be mounted onto the support structure.
5. Physical installation 3 2 5 10 6 4 7 9 1 Image 5-3 1. Adjust block 2. Hoist point. 3. Hoist point. 4. Adjust block 5. Insert nuts for 6 Handle 7. Insert nuts for 8. Handle 9. Insert nuts for 10. Insert nuts for 8 4 fixing tile fixing tile fixing tile fixing tile 2. Insert the M10 plain washer (Reference B) into the bolt (Reference A) 3. Insert the bolts into the corresponding holes of the mounting plates and let the mounting plate attache to the support structure.
5. Physical installation B Image 5-5 A 4X 4. Place a prevailing torque for the bolt (reference A) with the washer (reference B ) on each insert nuts of tiles. Do not fasten yet. 5. Level out the SF-10V tile. Use the adjust block in the bottom of tile for the height alignment; Tip: For maximum adjustment space in horizontal direction place the hex cap bolts of the every first SF-10V tile that is placed on the mounting plate in the middle of the corresponding slots. 6. Fasten the SF-10V tile.
5. Physical installation Example of SF-10V tile mounting 1 2 3 4 5 6 Image 5-6 How to get the height alignment between tiles Open the back door, using the long allen key rotate the socket head screw that located the bottom of tile as illustrated. If the allen key clockwise rotate the adjust block will go up, if rotate counter-clockwise the adjust block will go down.
5. Physical installation A B Adjust block screw. Long allen key(14mm) About cabling of Data cable between tiles. Considering the position of the data in/out sockets in SF-10Vtiles and dataI cable length, the cabling ways illustrated as follows are the only 2 possible ways.
5.
6. Dimensions 6. DIMENSIONS About this chapter This chapter contains drawings of the SF-10V tiles and its package, with the most important dimensions.
6. Dimensions 6.1 SF-10V tile Dimensions of the SF-10V tile 1280 mm 188mm 960 mm 910 mm 480 mm 223.
6. Dimensions 6.
6. Dimensions 6.3 SF-10V package Dimensions of the SF-10V tile package containing 4 tiles.
7. Specification 7.
7.
7. Specification 7.1 Specifications of theSF-10V tile Specifications of the SF-10V tile Pixel Pitch 20mm LED configuration 2R, 1G, 1B Pixel Density (real mode) 2,500 px/m² Pixel Density (virtual mode) 10,000 px/m² LED density 10,000 LEDs/m² Pixel per module HxV (real mode) 64x48 Pixel per module HxV (virtual mode) 128x96 Contrast ratio 2,000:1 Minimum Brightness 6,840 NIT Typical Brightness 7,200–9,800 NIT Color Processing 14 bit/color Colors 4.
7.
8. Order info 8. ORDER INFO About this chapter This chapter contains the order numbers of several important SF-10V peripherals. Overview • Order info • Spare part and service kits Consult the secured partner zone on WWW.My barco.com for an updated list with order numbers of the available SF-10V products.
8. Order info 8.1 Order info List with order numbers for SF-10V products 48 Order info Description R9004843B1 BME SF-10V 1TL BOX R9852560 BME P SLITE HOIST KIT R9852350 BME P SLITE RAIL KIT 896 R9850241 Power link cable of 1.5 meter. R9850250 Power link cable of 4.5 meter. R9850260 Power link cable of 9 meter. R9850280 Five dummy power plugs (for power output sockets) R9850210 Data link cable of 1.
8.
8. Order info 8.2 Spare part and service kits General Barco provides several kits for servicing SF-10V tiles. Below you find an order list of existing spare part and service kits. In the future new kits can be added to this list. Contact Barco to get an updated list.
9. Environmental information 9.
9. Environmental information 9.1 Disposal information Disposal Information Waste Electrical and Electronic Equipment This symbol on the product indicates that, under the European Directive 2002/96/EC governing waste from electrical and electronic equipment, this product must not be disposed of with other municipal waste. Please dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment.
9. Environmental information 9.2 Rohs compliance Turkey RoHS compliance Türkiye Cumhuriyeti: EEE Yönetmeliğine Uygundur.
9. Environmental information O: Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is below the limit requirement in SJ/T11363-2006. X : 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要求. X : Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this part is above the limit requirement in SJ/T11363 2006.
