How-To Guide

ManualsBrandsBarntools ManualsComputers & Accessories4G Gateway (US Version EC25-AF, LORA915MHZ)

Summary of content (31 pages)

PAGE 1
Directory Special statement................................................... 2 FCC Statement....................................................... 2 Gateway Instructions................................................ 3 The crates...................................................... 3 The interface is introduced..................................... 3 Install SIM card (optional)..................................... 4 Preparation before installation............................. 5 Installation steps.......
PAGE 2
How is the Q2 gateway paired with the sensor?.................. 26 After Q3 device is installed, how to bind the device on APP?错误！未定义书签。 In Q4 binding device, there is no such coded device prompt. How to solve this problem?............................................ 27 Q5 APP, power offline, how to solve?........................... 28 How to deal with the occurrence of sensor data in Q6 APP?...... 29 Q7 sensor how to replace the battery?..........................
PAGE 3
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. RF Exposure Statement The distance between user and products should be no less than 20cm.
PAGE 4
The interface is introduced The user can observe the flashing frequency of the indicator light to know the running status of the device. Indicator light color Running light green Paired indicator light red Indicator light flashing frequency destroy One second on and one second off Three seconds bright and three seconds dark On for 0.
PAGE 5
To install THE SIM card, be sure to cut off the power supply of the gateway and confirm that the device is in the state of shutdown.
PAGE 6
wiring  It is only operated by professionals. Unauthorized personnel are strictly prohibited to open it without permission.  When wiring, be sure to disconnect the power supply of the gateway and confirm that the equipment is in the state of shutdown. Step 1: Remove the six fixing screws on the gateway top cover and open the gateway top cover.
PAGE 7
The gateway contains the battery, please use it for the first time or after a long period of idle before use, first connect the mains charging for 15 minutes, then start using. Step 1: Install the antenna and connect the power supply as follows. Installation and fixation It is recommended that the gateway be installed in the workroom or in the distribution room and the equipment be secured by 4 expansion screws.  Do not flush with water, and do not open it without authorization.
PAGE 8
 The bottom of the antenna has magnets that can attach to metal objects.Please keep the head of the antenna away from the metal as far as possible and avoid shielding around, and keep a distance of more than 30cm between the two antennas. Temperature sensor Suitable for indoor temperature 1-5 and outdoor temperature sensor.  Be sure to use the battery as required or risk fire, explosion or combustion!  Only the same type of battery can be used when replacing the battery.
PAGE 9
approval The interface is introduced Understand the running status of the equipment by the flashing frequency of the indicator light.
PAGE 10
The second step is pairing the sensor with the gateway The sensor and gateway are on. Press and hold the red pairing button on the right side of the sensor and gateway at the same time. Hold the button for 10 seconds until the red pairing indicator of the two devices is on and the pairing is successful. Step 3 Sensor and gateway communication check Press the sensor pairing button and the green running indicator flashes once to indicate that the sensor is running normally.
PAGE 11
indicator flashes again, indicating that the sensor and gateway communication is normal. Notes:     Do not flush the sensor with water. To prevent condensation, remove the sensor after Posting and keep it properly. It is recommended that the sensor be disinfected by shining an ultraviolet lamp or wiping the surface of the device with alcohol. In order to avoid the injury of livestock and poultry to the equipment, it is recommended to install the sensor on the livestock and poultry back more than 20cm.
PAGE 12
The crates When opening the outer packing box, please check the appearance of the equipment for any obvious damage and confirm the list of items. The name of the The accessories number of The sensor 1 Certificate of 1 piece approval The interface is introduced Understand the running status of the equipment by the flashing frequency of the indicator light.
PAGE 13
light Begin to use The first step is to turn on the device According to the following diagram, turn on the power switch and the green indicator flashes once, and the boot is completed. The second step is pairing the sensor with the gateway The sensor and gateway are on. Press and hold the red pairing button on the right side of the sensor and gateway at the same time. Hold the button for 10 seconds until the red pairing indicator of the two devices is on and the pairing is successful.
PAGE 14
Step 3 Sensor and gateway communication check Press the sensor pairing button and the green running indicator flashes once to indicate that the sensor is running normally.Immediately after the red pair indicator flashes again, indicating that the sensor and gateway communication is normal.
PAGE 15
    Do not flush the sensor with water. To prevent condensation, remove the sensor after Posting and keep it properly. It is recommended that the sensor be disinfected by shining an ultraviolet lamp or wiping the surface of the device with alcohol. In order to avoid the injury of livestock and poultry to the equipment, it is recommended to install the sensor on the livestock and poultry back more than 20cm.
PAGE 16
Understand the running status of the equipment by the flashing frequency of the indicator light.
PAGE 17
The second step is pairing the sensor with the gateway The sensor and gateway are on. Press and hold the red pairing button on the right side of the sensor and gateway at the same time. Hold the button for 10 seconds until the red pairing indicator of the two devices is on and the pairing is successful. Step 3 Sensor and gateway communication check Press the sensor pairing button and the green running indicator flashes once to indicate that the sensor is running normally.
PAGE 18
Notes:     Do not flush the sensor with water. To prevent condensation, remove the sensor after Posting and keep it properly. It is recommended that the sensor be disinfected by shining an ultraviolet lamp or wiping the surface of the device with alcohol. In order to avoid the injury of livestock and poultry to the equipment, it is recommended to install the sensor on the livestock and poultry back more than 20cm. Gas sensor Suitable for carbon dioxide, ammonia and other gas sensors.
PAGE 19
The crates When opening the outer packing box, please check the appearance of the equipment for any obvious damage and confirm the list of items. The name of the accessories The number of The sensor 1 Certificate of approval 1 piece DC waterproof joint 1 The interface is introduced Understand the running status of the equipment by the flashing frequency of the indicator light.
PAGE 20
How to use The first step is to turn on the device The device supports 12V-24V power supply. Connect the device to the power adapter or the internal 12V interface of the gateway: According to the following diagram, turn on the power switch and the green indicator flashes once, and the boot is completed.
PAGE 21
The second step is pairing the sensor with the gateway The sensor and gateway are on. Press and hold the red pairing button on the right side of the sensor and gateway at the same time. Hold the button for 10 seconds until the red pairing indicator of the two devices is on and the pairing is successful. Step 3 Sensor and gateway communication check Press the sensor pairing button and the green running indicator flashes once to indicate that the sensor is running normally.
PAGE 22
Notes:     Do not flush the sensor with water. To prevent condensation, remove the sensor after Posting and keep it properly. It is recommended that the sensor be disinfected by shining an ultraviolet lamp or wiping the surface of the device with alcohol. In order to avoid the injury of livestock and poultry to the equipment, it is recommended to install the sensor on the livestock and poultry back more than 20cm.
PAGE 23
The crates When opening the outer packing box, please check the appearance of the equipment for any obvious damage and confirm the list of items. The name of the The accessories number of The sensor 1 4 core quick connector 1 How to use The first step is equipment wiring Refer to the figure below. Connect to the gateway by a 4-core cable sensor.The gateway opens and the sensor starts working.
PAGE 24
The second step is to check the sensor data through the mobile APP Notes:     Do not flush the sensor with water. To prevent condensation, remove the sensor after Posting and keep it properly. It is recommended that the sensor be disinfected by shining an ultraviolet lamp or wiping the surface of the device with alcohol. In order to avoid the injury of livestock and poultry to the equipment, it is recommended to install the sensor on the livestock and poultry back more than 20cm.
PAGE 25
Host gateway installation  The gateway shall be installed in the control room of the chicken house. The installation position must be more than 1.5 meters away from the controller in the operation room.  The ground terminals in the gateway must be reliably grounded;  The gateway USES municipal power supply. It is suggested to share the power with the farm controller to facilitate the monitoring of the power supply status of the controller.
PAGE 26
 The light sensor is recommended to be installed in the middle of the henhouse.The installation position is located between the two lighting fixtures in the shed lighting.In addition, the installation position must be far away from ventilation Windows, doors and other light-transmitting parts to avoid sudden changes in lighting data that may cause alarm notification.
PAGE 27
Solutions:  Open the gateway and sensor power switches. Wait 2 minutes after the gateway is turned on, and 30 seconds after the gateway is turned on.  At the same time, press and hold the gateway and sensor pairing button until both sides enter the constant light, indicating successful pairing. In Q3 binding device, there is no such coded device prompt. How to solve this problem? Solutions:  Observe whether the gateway operation indicator is flashing.
PAGE 28
 Check the antenna connector for looseness.  Observe the flashing status of the working indicator light; If the working indicator flashes once a second, please check the installation position of 4G antenna.Considering the structure of the farm house, it is recommended that the 4G antenna be extended outside.  Restart the device and observe the working indicator light after 2 minutes.The flicker frequency is once for 3 seconds, which means that the device is normal. You can try to bind again.
PAGE 29
 Observe whether the gateway operation indicator is flashing.If it does not flicker, contact an electrician to check the power supply at the gateway.  Indicator light flashes, indicating that the gateway power supply is normal.  Check the SIM card for traffic.  Check whether the antenna connector is loose:  Restart the gateway and observe the working indicator light after 2 minutes.
PAGE 30
 Press the sensor pair to see if the indicator light is on.Not bright means the sensor, power supply is normal.  Contact customer service to deal with it. Q6 sensor how to replace the battery? Solution: Please complete battery replacement according to the following operation manual.  Be sure to use the battery as required or risk fire, explosion or combustion!  Only the same type of battery can be used when replacing the battery.
PAGE 31
The above Suggestions are for reference only, users can adjust according to their own situation. Does the Q8 gateway have an indicator light to observe the running state of the device? Solution: During the startup process of the gateway, there is an indicator light inside the gateway, indicating the running state of the device.