User guide

TEST A (NON) REGISTERED PIN CODE
1. Test Factory Default PIN code 1234
- Close safe door and lock by turning the Knob (H) counter-
clockwise
- To begin the testing process, enter PIN code 1234, press
and release Enter Button (F)
- Door should NOT open; three short beeps will be heard
indicating PIN entry was incorrect
- If Factory Default PIN code 1234 opens the safe door, PIN
code registration was unsuccessful; and safe remains in
Factory Default PIN code mode
IMPORTANT: If registration was unsuccessful repeat steps
under PIN CODE REGISTRATION, and test Factory Default
PIN code
2. Test Registered PIN code
- Close safe door and lock by turning the Knob (H) counter-
clockwise
- To begin the testing process, enter new registered PIN code,
press and release Enter Button (F)
- Door should OPEN, one long beep will be heard indicating
PIN entry was correct, turn the Knob (H) clockwise to open
the safe
- PIN code registration was successful
CHANGE PIN CODE
1. Press and HOLD number “1” key until the green Indicator
Light (E) turns on, release button
- Enter current PIN code, press Enter Button (F), one long
beep will be heard
- Enter new PIN code (four to eight digits), press Enter Button
(F), two short beeps will be heard
- Re-enter new PIN code, press Enter Button (F), one long
beep will be heard
- PIN code has been changed
2. If you hear three short beeps with red/green Indicator Lights
(E) flashing, it indicates the new PIN code registration was
unsuccessful, repeat steps under CHANGE PIN CODE
3. Continue with TEST A (NON) REGISTERED PIN CODE
CLOSE/OPEN SAFE DOOR
CLOSE: Close the safe door and turn the Knob (H) counter-
clockwise to lock the safe
OPEN WITH FINGERPRINT:
- Press and release Enter Button (F)
- Place a registered finger on the Fingerprint Scanner (D)
- One long beep will be heard and the green Indicator Light
(E) turns on
- Turn the Knob (H) clockwise to open the safe
OPEN WITH PIN CODE:
- Enter PIN code, press Enter Button (F)
- One long beep will be heard and the green Indicator Light
(E) turns on
- Turn the Knob (H) clockwise to open the safe
DOOR OPEN ALARM
The door alarm is activated ONLY when the safe door is left
open and the Bolts (C) are retracted
1. Within 1 minute, the green Indicator Light (E) will start
flashing, followed by one beep
- It will beep every 3-5 seconds
- Close the safe door, and turn the Knob (H) counter-
clockwise to cease the alarm
2. With the safe door open and the Bolts (C) extended, no
Indicator Lights (E) or beeps will be heard
LOW BATTERY WARNING
1. When the door is closed and the Indicator Light (E) displays
red, this indicates batteries are low. Replace batteries
immediately
2. Use Emergency Key to open safe
- To expose the Emergency Key Access, remove Logo Plate
(I) screws with tool provided
- Insert Emergency Key into key access, push and turn
counter-clockwise
- Turn the Knob (H) clockwise to open
3. Replace batteries
- Remove Battery Compartment (B) cover and all
4 AA batteries
- Insert 4 new AA batteries and restore Battery
Compartment (B) cover
Note: All registered fingerprints and PIN code remain stored
DELETE STORED FINGERPRINTS AND PIN CODE /
RESET TO FACTORY DEFAULT MODE
1. Open the safe door
- Press and HOLD the Initialization Button (A)
- The green Indicator Light (E) will flash approximately fifteen
times, followed by one long beep
- RELEASE Initialization Button (A)
2. If the green Indicator Light (E) did not flash and one long
beep was not heard, repeat step 1
3. All fingerprints and the PIN code stored in the safe have
been deleted
Note: The safe is in Factory Default mode. NO fingerprint can
open the safe. Only the Emergency Key or the Factory Default
PIN code 1234 can open the safe. To add a fingerprint refer to
steps in "FINGERPRINT REGISTRATION".
CARE AND MAINTENANCE
- To maximize the security and performance of the safe, keep
Fingerprint Scanner (D) clean; use a dry cloth to remove any
smudges or prints off the Fingerprint Scanner after each use
- Test registered fingerprints and PIN code every 6 months
- Keep liquids away from the control panel. Spills on the control
panel will cause damage and possibly electric shock
- Secure safe in a proper area to prevent from falling and
causing damage or injury
- DO NOT disassemble the product. For all repairs, contact
BARSKA Customer Service
- DO NOT use chemicals or cleaning agents to clean the safe
MOUNTING INSTRUCTIONS
The safe may be mounted to a wall or
floor. Be aware of the load bearing.
Failure to do so can result in personal
injury and/or damage to property. Use
appropriate tools when performing
work and always use eye protection
Wall Mounting
Do not mount the safe without anchoring to the wall
- Find the studs in the wall, at your desired location. Most studs
are 16 inches or 24 inches apart
- Check the wall for concealed wires or pipes
- Measure the location of the pre-set drill holes; mark their exact
position onto the wall ensuring that the studs or anything else
behind will not interfere
- Drill the appropriate size holes for the anchors you are using
- Carefully press the anchor into the holes at this time
- Mount the safe by running screws from inside of the safe and
securing to anchors; ensure the safe is mounted securely
Floor Mounting
- Use proper drill tools depending on the type of floor you are
mounting the safe (wood, tile, or concrete)
- Measure the location of the pre-set drill holes; mark their exact
position onto the floor
- Drill the appropriate size holes for the anchors you are using
- Carefully press the anchor into the holes at this time
- Mount the safe by running screws from inside of the safe and
securing to anchors; ensure the safe is mounted securely
* Actual model may vary
Mounting Holes