09248
INSTRUCTION MANUAL FOR DISHWASHERS UK CONTENTS CHAP 1 PREFACE ................................................................................................................... 2 CHAP 2 INSTALLATION .......................................................................................................... 2 UNPACKING ...................................................................................................................... 2 POSITIONING .......................................................
INSTRUCTION MANUAL FOR DISHWASHERS UK Chap 1 PREFACE This manual contains important safety warnings relating to installation, use and maintenance. Failure to observe the instructions in the enclosed documentation may compromise the safety of the appliance and immediately voids the warranty.
INSTRUCTION MANUAL FOR DISHWASHERS UK 2.2 Positioning • • • • • • Check that there are no objects or materials in the installation area which may be damaged by the steam emitted by the appliance during operation, or if there are, make sure they are properly protected.
INSTRUCTION MANUAL FOR DISHWASHERS UK 2.4 Water circuit hookup The appliance must be connected to its water supply with a flexible hose. A shut off valve (cock) must be installed between the water supply line and the appliance's solenoid valve. The cock must be close to the appliance. • • • The water supply, temperature and pressure must be compatible with the ratings on the machine's nameplate.
INSTRUCTION MANUAL FOR DISHWASHERS UK Chap 3 RISKS AND IMPORTANT WARNINGS • • • • • • • • • • • • • • • • • • • • • • This appliance is intended solely for the use for which has been designed. Any other use is improper and hazardous. The specialised technician responsible for installing the appliance must instruct the user on its operation and any attendant safety measures, including practical demonstrations.
INSTRUCTION MANUAL FOR DISHWASHERS UK Chap 4 USING THE MACHINE 4.1 Key and symbols Referring to Fig.1: 1 ON/OFF LED AND BUTTON 2 PROGRAMME SELECTION BUTTON 5 CYCLE LED 3 START BUTTON 6 STATE LED 7 AUTOMATIC START LED (hood only) 4a WASHING TEMPERATURE DISPLAY 4b RINSE TEMPERATURE DISPLAY Short washes Drain cycle Medium wash Resin regeneration Long wash Continuous wash 4.2 Switching the dishwasher on Referring to Fig.
INSTRUCTION MANUAL FOR DISHWASHERS 4.4 • • • • • • • • • • • UK Cycle selection and start-up 4.4.1 Under-counter dishwashers Press the PROGRAMME SELECTION (2) button repeatedly to select a wash cycle that is suitable for the dishes to be washed; the cycle LED lights up to indicate the cycle chosen (Fig. 4). To run the programme, press START (3); the CYCLE LED (5) corresponding to the chosen wash cycle starts to flash. When the cycle is completed, it stays on, fixed.
INSTRUCTION MANUAL FOR DISHWASHERS UK 4.8 Turning the dishwasher off • Press ON/OFF (1), on the DISPLAY (4) the central segments will light up, indicating that the machine is powered. 4.9 Resin regeneration (*optional) On machines with an internal softener, when the regeneration cycle led lights up red (Fig. 11) you need to run a regeneration cycle to restore proper function of the internal softener. Proceed as follows: • • • • • • • • • • Empty and clean the dishwasher.
INSTRUCTION MANUAL FOR DISHWASHERS UK Chap 5 MAINTENANCE 5.1 General rules Before doing any maintenance, completely drain out all water, shut off the power supply and close the water supply cock. Do not use water under pressure - it can damage the electrical equipment. Only wash the body panelling when it is cold, using only product specifically designed for steel. If there is a risk of ice forming, drain the water from the boiler and wash pump. 5.
UK INSTRUCTION MANUAL FOR DISHWASHERS Chap 6 SELF DIAGNOSTICS The machine is equipped with a self-diagnosis system that registers and warns of a number of malfunctions. Fault Description and possible remedies No rinsing. The rinsing cycle was not completed correctly. Make sure that the rinsing nozzles are clean. No drainage. The water was not drained or drained incorrectly. Check that the drain pipe is not bent or crushed and that the siphon and filters are not blocked.
INSTRUCTION MANUAL FOR DISHWASHERS UK Chap 7 SETTINGS The following settings should only be configured by a qualified technician. The parameters listed below can be set during installation of afterwards, accessing the settings menu as follows: • Machine in standby with door open. • Press buttons 2 and 3 together (cycle selection and START) for 5 seconds and enter the key CH 12 (buttons 2 and 3 to change the parameter, 1 to confirm).
INSTRUCTION MANUAL FOR DISHWASHERS UK 7.1 Number of cycles to regenerate resins The number of cycles between one resin regeneration and the next depends on the hardness of the local water, and should be set in accordance with the table shown. Set the parameter dH in the settings menu as described in the paragraph: dH °F No. Cycles dH °F No. Cycles dH °F No. Cycles dH °F No.