INSTALLATION INSTRUCTIONS UNIT No. 3600 FRAMELESS PIVOT SHOWER DOOR QCI0020 Rev. 3 Page 1 of 8 1-800 NE INSTA ED LLAT HELP ION ? Call ASCO -45-B (452Mon 2726 8:00 day - Frida ) A.M. y Easte - 4:30 P.M .
MAINTENANCE: Two primary materials are used to manufacture your new Basco enclosure: tempered glass and anodized aluminum. To assure a long lasting finish on the enclosure, wipe it down with a towel after each use. Never use a scouring agent to clean the aluminum. For occasional, more concentrated cleaning efforts, we find that Lysol Bathroom Cleaner works extremely well. Be sure that any over spray falling on the aluminum frame is rinsed thoroughly and dried.
600 Parts List A. B. C. D. E. F. G. H. 1 Curb 1 Roll of Tape (double-stick) 1 Pivot Jamb Seal Vinyl 1 Pivot Jamb 2 Pivot Brackets 3 #6 x 3/8” Truss Head Screws 2 #8 x 1/8” Allen Set Screws 1 Allen Wrench (5/64”) QCI0020 Rev. 0 J. K. L. M. N. P. R. S. 6 Plastic Wall Anchors 3 #8 x 2” Truss Head Screws 1 Glazed Door Panel 1 Bottom Rail 2 #10 x 7/16” Set Screws 2 Pivot Blocks 2 Nylon Bushings 1 Strike Jamb (w/ Magnet) Page 3 of 8 T. U. V. W. X. Y. AA. BB.
The Basco 3600 Frameless Pivot Shower Door is completely reversible and may be installed pivotright or pivot-left. Refer to the illustration to determine the correct position for your installation. For maximum waterproofing, the pivot jamb should always be opposite the shower head. These instructions depict a pivot-left installation. CAUTION: For safety, the door must always open outward. 2 Note: The 3600 unit may be installed without using the sloped curb [A] provided.
4 Cut the clear pivot jamb seal vinyl [C] 3/4” shorter than the pivot jamb [D]. Slide the jamb seal vinyl into the slot in the pivot jamb. Lubricating the vinyl with a small amount of soapy water will help installation. Slide one of the pivot brackets [E] into the bottom of the pivot jamb. Lock it in place with a #6 x 3/8” truss head screw [F] and a #8-32 x 1/8” set screw [G] (a 5/64” Allen wrench [H] is provided). NOTE: Set screws [F] are pre-installed.
7 Thread the two #10-24 x 7/16” square head set screws [N] into the tapped holes in the pivot blocks [P]. Slide the pivot blocks into the top and bottom rails of the glass door panel [L] with the stainless steel pins toward the pivot side of the door (see details). Measure the distance from wall to wall directly above the curb (Dim. “A”). Deduct 3 ¾” from this amount and position the pivot pins this exact distance (Dim “B”) from the strike edge of the glass.
10 Slide the door handle [U] with magnet onto the strike edge of the door panel [L]. Close the door and slide the handle up or down until the two magnetic strips are aligned. Use a pencil or masking tape the mark the location of the handle on the door. Slip the door handle vinyl [V] onto the door between the marks and carefully drive the door handle on the door panel (USING RUBBER OR PLASTIC MALLET). Spraying glass cleaner or water onto the vinyl and handle will make the assembly easier.
13 Press the four rail end caps [AA] into the ends of the top and bottom door rails. A small dab of clear silicone will hold caps in place. Peel the backing from the BASCO decal [BB] and apply it to the pivot jamb as shown in the detail. NOTE: Do not use a metal hammer to install the end caps. 14 Neatly caulk the inside perimeter of the shower curb and the pivot and strike jambs. NOTE: The caulking should be allowed to cure for twenty-four hours before using your new shower enclosure.