INSTALLATION INSTRUCTIONS 3/8” FRAMELESS BYPASS SLIDING SHOWER ENCLOSURE QCI-5017 QCI5017 Rev.
INSTALLATION NOTES: Unpack your unit carefully and inspect for freight damage. Lay out and identify all parts using the instruction sheet as a reference. Before discarding the carton, check to see that no small hardware parts have fallen to the bottom of the box. If any parts are damaged or missing, refer to the descriptions noted in the instructions when contacting your dealer for replacements. Handle the glass panel(s) carefully and protect the edges.
/8” FRAMELESS BYPASS SLIDER PARTS LIST G F A ITEM QTY DESRIPTION A 2 WALL JAMB B BOTTOM TRACK SC624 1 AND VINYL SCV190 C 6 WALL PLUG D 6 #8 X 2" SCREW SCR15 E 4 BUMPER SC4347 F 2 T-LOCK SC4339 G 4 HEADER SC623 H 4 HANGER SC1615 J M 2 GLASS PANEL TOWEL BAR 2 ASSEMBLY HEAVY DUTY 4 ROLLER V 1 BOTTOM GUIDE SC4047 W 2 GUIDE SCREW K H PART NUMBER LA0622 SC4106 —- K SEE PAGE 6 SC4082 SCR24 J H—SC1615 EXPLODED VIEW J ITEM QTY DESRIPTION L 1 HANGER BRACKET M N 1 1 ROLLER #8
1 This framess bypass sliding enclosure is supplied with custom fit Wall Jambs [A]. The jambs are notched one end to fit over the bottom track. For maximum waterproofing, position the inner panel to close to wall where the shower head is located. 2 Measure the wall-to-wall opening along the center of the threshold at the bottom. Cut the Bottom Track (W/ Vinyl Silencer) [B] 1/16” short of that dimension. Position the bottom track in the center of the threshold with the raised edge to the exterior.
Alternative Method: SIL ICO 4 NE Before replacing the track, force a slight downward bow into it. This will ensure that the track fits tight to the threshold in the middle. Run 2 beads of silicone inside the pnecil marks on the threshold. Place the tub track in position over the silicone, lining it up with the pencil marks on the threshold from the previous step. Run a bead of silicone on both flat surfaces on the bottom of the track.
This enclosure is equipped with molded nylon T-Locks [F] for safety. When properly installed, the header is locked in the wall jambs and cannot be accidently removed. Measure the wall-to-wall opening at the top of the wall jambs. Cut the header 1/16” short of that dimension. Check for fit. TIP: Use a miter box to ensure a straight cut Slide the T-Locks into the header. Set the header down onto the wall jamb with the T-Lock fitting into the space behind the wall jamb.
8 From the outside of the shower, lift the inner panel into place with the rollers (and textured side of glass) facing you. Lower it into the shower and then lift it into the header. Be sure the bracket fins and rollers are above the track groove. Carefully lower the panel until the rollers are seated into the groove. Slide the panel to one side and repeat the steps, lifting the outer panel into place. Check for alignment along the bottom and sides of each panel and adjust the rollers as necessary.
11 Neatly silicone each end of the tub track where it fits into the wall jambs as well as the seam between the wall and the wall jamb and the curb and threshold on the inside of the shower. r. Optional: Silicone between the walls and wall jambs, and the curb and threshold on the outside of the shower. NOTE: DO NOT USE the shower until the silicone is completely cured. Check the tube of silicone for the manufacturer recommended cure time. (typically 24 - 48 hours) QCI5017 Rev.
12 ANTI-JUMP, Installation HEADER ANTI-JUMP Note: Illustrations may not match your specific model, but installation procedure Step - 1 is the same. Place one Anti-Jump on each Bracket Hanger: two per panel: four total. BRACKET HANGER HEADER ANTI-JUMP Step - 2 ANTI-JUMP BRACKET HANGER HEADER ANTI-JUMP Step - 3 HEADER BRACKET HANGER BRACKET HANGER If the Anti-Jump does not stay in the place or if it is difficult to insert, snap off the "roller side leg" leaving one remaining leg. QCI5017 REV.
