Unit No. 160QNS Deluxe Pivot Framed Door Neo Angle Shower Enclosure QCI0012 REV.
MAINTENANCE: Two primary materials are used to manufacture your new Basco enclosure: tempered glass and anodized aluminum. To assure a long lasting finish on the enclosure, wipe it down with a towel after each use. Never use a scouring agent to clean the aluminum. For occasional, more concentrated cleaning efforts, we find that Maintain AquaGlideXP Spray Cleaner helps minimize water stains and oxidation.
160 Quick-N-Stall Parts List K. L. M. N. P. R. S. T. V. A. 3 Curb Sectons B. 4 135 Anchor Plates C. 30 #8 x 1/4” Truss Head Screws D. 3 Header Sections E. 2 Wall Jambs F. 6 Plastic Wall Anchors G. 6 #8 x 1 1/2” Truss Head Screws H. 2 Pre-Glazed Side Panels J. 2 135 Posts 2 1 1 1 2 1 2 1 1 Clear Vinyl Jamb Seals Glazed Door Panel Pivot Jamb Strike Jamb (Magnetic) Snap-in Fillers Drip Rail Drip Plugs Tapered Drip Vinyl Roll Double Stick Taped W. X. Y. AA. BB. CC. DD. EE. 2 1 2 1 1 1 2 1 #10 x 7/16” Sq.
1 The BASCO 160 Quick-N-Stall Shower Enclosure is completely reversible and may be installed pivot-left or pivot-right. For maximum waterproofing, the pivot jamb should be opposite the shower head. Using the diagram, determine the correct position for the door in your particular Quick-N-Stall installation. This instruction sheet depicts a pivot-right installation. CAUTION: For safety reasons, the door panel must always open outward.
4 Place the two wall jambs [E] into the ends of the curb assembly [A]. Plumb the jambs and mark the hole locations on the wall. Masking tape may be used to hold the curb in place during this operation. Remove all parts and drill the walls for mounting hardware. WALL JAMB For tile or marble walls, drill six 3/16” diameter holes and insert the plastic wall anchors [F]. Attachments to fiberglass or acrylic units can be made in two ways.
7 MEASURE AT TOP OF JAMBS AND POSTS HEADER ASSEMBLY Using a 3/16” drill bit, drill the interior face of the header assembly on both ends as shown. These holes may be predrilled from the factory. 3/16” 1/4” IN DIA. 3/8” TE RIO R 8 Press the header assembly [D] over the wall jambs [E], the 135° posts [J] and the pre-glazed panels. Check the posts for plumb. Adjust as required by varying the overlap of the header over the wall jambs.
(%!$%2 !33%-",9 6QDS WKH ILOOHUV >3@ LQWR WKH FXUE DVVHPEO\ >$@ DQG KHDGHU DVVHPEO\ >'@ EHWZHHQ WKH GRRU MDPEV ZLWK WKH 5$,6(' /,3 72 7+( (;7(5,25 DQG WKH SLYRW KROHV WRZDUG WKH SLYRW MDPE >0@ &HQWHU WKH FXUE ILOOHU LQ WKH FXUE EHWZHHQ WKH SLYRW DQG VWULNH MDPE >1@ XVH PDVNLQJ WDSH WR KROG LQ SRVLWLRQ 127( 7KH VQDS LQ ILOOHUV VKRXOG EH H[DFWO\ ´ ORQJHU WKDQ WKH GRRU SDQHO ZLGWK &),,%23 0)6/4 *!-" (/,% &/2 0)6/4 "53().' %84%2)/2 3.!0 ).
13 HEADER Insert the two nylon pivot bushings [Y] into the pivot holes in the head and curb fillers [P]. Lift the door panel [L] and insert the top pivot pin into the pivot bushing in the header filler. Hold the door vertical and insert the bottom pivot pin into the pivot bushing in the curb filler. It may be necessary to remove the header retaining screws and raise the header slightly to install the door.
16 (2) HANDLE SCREWS Attach the interior door handle [BB] and the exterior door handle [CC] to the door panel [L] with two #6-32 x 1 1/4” round head screws [DD]. Close the door and check the clearance with the strike jamb [N]. If necessary, loosen the set screws [W] on the top and bottom slide bars and adjust the door panel to align the strike magnets. When the door panel is properly aligned, tighten the set screws securely.