INSTALLATION INSTRUCTIONS Neo Angle DELUXE FRAMED CONTINUOUS HINGE SHOWER ENCLOSURE QCI0237 Page 1 of 10
INSTALLATION NOTES: Unpack your unit carefully and inspect for freight damage. Lay out and identify all parts using the instruction sheet as a reference. Before discarding the carton, check to see that no small hardware parts have fallen to the bottom of the box. If any parts are damaged or missing, refer to the descriptions noted in the instructions when contacting your dealer for replacements. Handle the glass panel(s) carefully and protect the edges.
Parts List A. Curb Assembly (w/ weep holes) (1) B. #8 x 1/4” Truss Head Screw (14) C. Header Assembly (2) D. Wall Jamb (2) E. Plastic Wall Anchor (6) F. #8 x 1 1/2” Truss Head Screw (6) G. Setting Block (4) H. Return Glass Panel (2) I. Corner Post (2) J. Strike Jamb w/ magnet (1) K. Door Panel Assembly (1) K1. Hinge Jamb QUICK ’N S TALL L. Snap-in Filler (2) M. Drip Rail (1) N. Double Sided Tape (1) O. Tapered Drip Vinyl (1) P. #6 x 3/8” Screw (1) Q. Drip Plug (1) R. Interior Door Handle (1) S.
1 The Framed Continuous Hinge Shower door panel is completely reversible and may be installed hinge right or hinge left. For maximum waterproofing, the door should hinge off of the panel opposite the shower head wall. (see illustration) Careful as to not follow the illustrations exactly. CAUTION: For safety reasons, the door must always open outward.
4 Place one wall jamb [D] into the curb against the wall. Using a level, plumb the wall jamb and mark the hole locations on the wall with a pencil. Repeat this step for the other wall jamb. Remove all parts and drill the holes. TIP: Tape can be used to temporarily hold the curb in place. WALL WALL JAMB WALL JAMB CURB Tile or marble walls: Drill 3/16” diameter holes into the walls and insert the plastic wall anchors [E]. CURB Fiberglass or acrylic units can be done two different ways.
Place four setting blocks [G] into the curb, flat side up, to support the stationary glass panels (two blocks per panel). Position the blocks so they are centered about 3” from each corner of the glass panels. Set the stationary glass panels [H] into the curb on the setting blocks and slide into the wall jamb approximately 1/2“. A piece of tape positioned 1/2” from the vertical edge will help placement.
9 Slide the strike jamb [J] over one of the corner posts. Be sure that the magnet is facing the exterior. Use a piece of tape to temporarily hold it in place. Orient the door to the opening (either hinge right or hinge left). Grab the door from the inside (the open side of the hinge jamb should be away from you). FILLERS EXTERIOR Carefully lift the door [K] into the opening and slide the hinge jamb [K1] over the other corner post.
11 Clean the bottom door rail and the drip rail [M] thoroughly to ensure proper adhesion. Unroll the double stick tape [N] and carefully apply it to the flat back side of the drip rail. (DO NOT peel the tape backing yet) DOOR RAIL DRIP RAIL ALIGN (HINGE SIDE ONLY) TAPERED VINYL Insert the tapered drip vinyl [O] with the short side of the vinyl on the hinge side of the rail.
13 Attach the interior door handle [R] and exterior door handle [S] to the door panel with the two #6-32 x 1 1/4” round head screws [T]. DOOR STRIKE RAIL #6-32 x 1 1/4” HANDLE SCREWS Close the door and check the clearance with the strike jamb. Loosen and adjust if necessary.
16 Cut the eight (8) pieces of the horizontal vinyl [V] 1/2” longer than the horizontal opening. Cut both ends of the vinyl with a back mitre so that they sit tight against the face of the vertical vinyl. (see illustration) VINYL REMOVE HORIZONTAL OPENING HEADER Starting at the top on the exterior, place the vinyl against the glass (open side against glass) and press into the header at both corners. Continue pressing vinyl into the header from both ends working toward the middle.
