INSTALLATION INSTRUCTIONS FRAMELESS FIXED PANEL SLIDER QCI-5150 QCI5150 Rev 0 Page 1
FRAMELESS FIXED PANEL SLIDER PARTS LIST ITEM NUMBER PART NUMBER 1 SC893 2 SC938 3 SC938 4 SC892 5 SCV912 6 SCV353 7 SC4700 8 SC4640 9 SC4800-01 10 SC4800-02 11 SC4610 12 SC4710 13 SC4910 14** SC4295 15** SC4296 16** SC4106 18** SCR09SV 20** SCV924/SCV925 DESCRIPTION HEADER TUBE HORIZONTAL U-CHANNEL VERTICAL U-CHANNEL SNAP IN FILLER DRIP VINYL DOOR TO PANEL VINYL WALL MOUNT HEADER BRACKET PANEL CLAMP WITH ANTI-JUMP ROLLER ASSEMBLY WITH STOPPER ROLLER ASSEMBLY PANEL GUIDE DOOR CATCH 18" PULL HANDLE 1/8" BUMP
FRAMELESS FIXED PANEL SLIDER QCI5150 Rev 0 Page 3 Certified 6/6/2016
Tools: To install your New Shower Enclosure, you may need the following: Drill Pencil Hack Saw 1/8” & 3/16” Drill Bit Low Tack Tape Caulk Gun Center Punch Tape Measure Clear Silicone Caulk Files 4’ & 6’ Levels Suction Cups #2 Phillips Screwdriver Safety Notes: This unit is best installed by two people. Handle the glass panels carefully and protect the edges.
1 If a continuous unit centerline does not exist from the original measuring process, it will be necessary to create one. Lightly mark a continuous unit centerline on the threshold. Next, mark a continuous unit centerline on each wall, starting where the threshold centerline meets the wall. Use a level to ensure the wall centerline is plumb and straight. The wall centerlines should be a minimum of the unit height from the threshold.
3 Verify that the U-channels is cut [2] to the appropriate size. This piece of U-channel will be equal to the opening width. Next drill three 3/16” diameter holes in the center of U-channel [2] (centerline groove provided for convenience), two holes approximately 4”from each end and one in the middle. Place the U-channel in its correct position with the u-channel centerline over the threshold centerline as marked in step one. With a pencil carefully mark each hole position on the threshold centerline.
5 Verify that the U-channel [3] is cut properly using the below formulas: U-channel Height = Unit Height - 2 3/4” or U-channel Height = Panel Glass Height - 9/16“ Note: If out of level conditions exist be sure to use the longer U-channel on the appropriate side (see illustration). Next, drill three 3/16” diameter holes in the center of U-channel (centerline groove provided for convenience); one hole 4” from each end and one hole in the middle. Place the U-channel over the all centerline marked in step one.
7 Disassemble two Wall Mount Header Brackets [7] by loosening the set screws. Screw the inner part of the Header Bracket [7] into the wall with the supplied socket countersunk head screw. REMOVE AND DISCARD THE INCLUDED WALL PLUG 8 Check the size of the Header [1]. It should be equal to the opening size minus 1 1/2”(+/- 1/8” tolerance).
Place 1/8” setting blocks [20] into the U-channel as shown or approximately every 18”. DO NOT place setting blocks over screw heads, but set them close to ensure that the screw heads are below the setting blocks. Using suction cups set, the Stationary Glass Panel into the U-channels on the appropriate side. Use different sizes of setting blocks to make exposed edges of the glass level and plumb.** Exposed edges MUST be level and plumb before moving to next step.
Remove the Anti-Jump from the clamp [8]. Loosen the Clamp screw but DONOT remove it. Slide the Clamp [8] over the glass panel and the Header [1] with the screw on the inside of the shower. Set a distance between the exposed glass edge and the Clamp [8] equal to 1/4” then tighten the screw. 11 Measure the width of the Door Panel. Place a mark on the threshold measuring the same distance from the open wall (See illustration).
12 Take the Roller with Stopper Pin [9] and set the roller cam shaft by loosening the set screw with the 4mm Allen wrench and rotate the cam shaft to set the adjustment hole to horizontal then retighten the set screw. Do the same steps with the Roller [10]. Remove mount bolts and washers before mounting the Roller Assemblies [9/10] to the Door Panel. Note: The Rollers [9/10] have +/-1/8” height adjustment.
15 Carefully hang the Door Panel with Rollers [9/10] on the Header [1]. Make sure the Door Panel is lined up inside the Guide [11]. Then, if necessary adjust the Door Panel so the top of the glass is flush with the Stationary Panel by loosening the set screw located on the top of the Roller Assembly with 4mm Allen wrench and rotating the cam shaft.
16 Reinstall the Anti-jumper on the Clamp [8] which was removed from the Clamp in step 10. 17 Install the Vinyl Seal [6] or the Bumpers [14/15] Vinyl Seal: Cut the Vinyl to size equal to the Door Panel height minus 1/2”. Place the Vinyl onto the wall side of the door panel with the lip facing inside the shower. Bumpers: Locate the self adhesive bumpers 1/2” from the top and bottom edges of the door panel where it meets the wall. Thoroughly clean with alcohol swabs and dry the wall.
18 Install the Pull Handle [13] or Knob [13] onto the door as shown. 19 Place the Bottom Catch [12] onto the bottom of the Door Panel approximately 1/4” from the edge of the door. Completely close the door and adjust location of the Bottom Stopper (see illustrations). Mark its location on the glass (a small peace of tape works best). Remove the Bottom Catch and apply a small amount of silicone to the inner surfaces of the Catch. Place the Catch back onto the glass at its marked location.
21 On the interior face of the Side Panel, place a strip of low tack tape on the glass about 1/8” to 3/16” away from edge of the u-channel both vertically and horizontally. Run a small bead of silicone along this edge. Finally on the interior, run a bead of silicone between the u-channel and the threshold and also between the u-channel and the wall. After completing, remove the tape before silicone sets. NOTE: DO NOT USE the shower until the silicone is completely cured.
